Toshiba MMY-MAP0806HT8P-E Installation Manual page 80

CODE No.
SET DATA
SETTING
UNIT No.
R.C. No.
TEMP. ON / OFF
1 TIMER SET
TIME
FILTER
RESET TEST SET CL
6
2
3
(Execute it while the units are stopped.)
You can check indoor unit addresses and positions of
the indoor units in a single refrigerant line.
When an outdoor unit is selected, the indoor unit
numbers of the refrigerant line of the selected unit are
indicated one after another and the fan and louvers of
the indicated indoor units are activated.
1
Push and hold the TIME and
at the same time for more than 4 seconds.
At first, the line 1 and CODE No.
(Address Change) are indicated on the
LCD display. (Select an outdoor unit.)
2
Push the (left side of the button)
and buttons repeatedly to select a
system address.
3
Push the button to confirm the system
address selection.
The address of an indoor unit connected to the
•
selected refrigerant line is indicated on the LCD
display and its fan and louvers are activated.
4
Push the button (left side of the
button). Each time you push the button,
the indoor unit numbers of the selected
refrigerant line are indicated one after
another.
• Only the fan and louvers of the indicated indoor
unit are activated.
¿ To select another system address
5
Push the CL button to return to step
2
After returning to step , select another system
•
address and check the indoor unit addresses of
the line.
6
Push the button to finish the procedure.
157-EN
1117101201-3 EN.indd 79 1117101201-3 EN.indd 79
Changing the indoor unit
address using a remote
controller
To change an indoor unit address using a
wired remote controller.
q The method to change the address of an
individual indoor unit (the indoor unit is
4 paired with a wired remote controller one-to-
one), or an indoor unit in a group.
(The method is available when the addresses
5
have already been set automatically.)
CODE No.
SET DATA SETTING
UNIT No.
R.C. No.
TEMP. ON / OFF
3
5 TIMER SET
buttons
TIME
FILTER
8 RESET TEST SET CL
Finish
1 2, 6, 7
(Execute it while the units are stopped.)
1
Push and hold the , , and
at the same time for more than 4 seconds.
(If 2 or more indoor units are controlled in a
group, the first indicated UNIT No. is that of the
head unit.)
2
Push the button (left side of the
button) repeatedly to select an indoor unit
number to change if 2 or more units are
controlled in a group. (The fan and louvers
of the selected indoor unit are activated.)
(The fan of the selected indoor unit is turned on.)
3
Push the TEMP. / buttons
repeatedly to select for CODE No..
4
Push the TIME / buttons repeatedly
2
.
to change the value indicated in the SET
DATA section to that you want.
5
Push the button.
– 79 –
6
Push the button (left side of the
button) repeatedly to select another indoor
UNIT No. to change.
4 6
Repeat steps to to change the indoor unit
addresses so as to make each of them unique.
7
Push the button (left side of the
button) to check the changed addresses.
8
If the addresses have been changed
correctly, push the
procedure.
4
buttons
q To change all the indoor unit addresses
using an arbitrary wired remote controller.
(The method is available when the addresses
have already been set automatically.)
(When communication wirings of 2 or more
refrigerant lines are interconnected for
central control)
NOTE
button to finish the
You can change the addresses of indoor units in
each refrigerant line using an arbitrary wired remote
controller.
* Enter the address check/change mode and change
the addresses.
SET DATA SETTING
TEMP.
TIMER SET
1
TIME
FILTER
RESET TEST SET CL
3
Cancels the line selection
If no number appears on UNIT No., no outdoor unit
exists on the line. Push
2
line following step .
(Execute it while the units are stopped.)
1
Push and hold the TIME
at the same time for more than 4 seconds.
At first, the line 1 and CODE No.
(Address Change) are indicated on the
LCD display.
2
Push (left side of the button)
and buttons repeatedly to select a
system address.
CODE No.
UNIT No.
R.C. No.
ON / OFF
2
button and select another
and buttons
158-EN
8/8/2559 BE 3:49 PM 8/8/2559 BE 3:49 PM