Advertisement
Set up
1
Approximate time: 10 minutes
Note: Leave any cables that are already connected to the Wi-Fi gateway as they are.
For best results, connect only the
devices/adapters depicted below.
Phone ports
Note: Leave any
cables already in
these ports as
they are.
Yellow
Ethernet ports
Power port
Wi-Fi Gateway—back panel
a
Connect the new yellow Ethernet cable from an open/available Wi-Fi Gateway Local Ethernet port to the
computer Ethernet port.
B
Connect the gray phone cord from the Wi-Fi Gateway Lines 1 & 2 port to your phone. If you are using a
cordless phone, make sure the base station is plugged into an electrical outlet.
Power Up
2
Important: You will temporarily lose your at&t U-verse®
tV service and your tV/DVR connection during this step.
Attach your battery backup unit:
•
Power down your Wi-Fi Gateway by unplugging the power
adapter from the wall and the Wi-Fi Gateway. You will no
longer need this power supply.
•
Connect the battery backup unit by plugging it into an
electrical outlet. Then plug the round connector into the
Power port on the Wi-Fi Gateway .
Switch the power to On. You should see a solid green
Power light to indicate a successful power connection.
See the "Having trouble?" and "Specific issues" sections on the
Questions?
back of this guide for tips and answers to common questions.
Phone or cordless
base station
B
a
Yellow
Ethernet cable
PC Ethernet port
Electrical outlet
Approximate time: 10 minutes
Before
After
Check your Internet connection:
•
On the Wi-Fi Gateway, make sure the indicator lights for Broadband and Service
turn solid green and that the indicator light for Local Ethernet is blinking green.
If the Broadband and Service lights do not turn solid green or continue to blink
after 10 minutes, see
Having trouble?
During this time, do not unplug the power adapter.
this can damage the Wi-Fi Gateway and interrupt
your tV service.
Registration & Activation
3
Approximate time: 20 minutes
Note: You must complete both activation steps in order to use your Internet and Voice services.
Important: You will have a dial tone after completing step
emergency and toll-free calls until you activate your Voice service in step
Open your Internet browser (e.g., Internet
a
Explorer, Safari, etc.):
•
The online registration process will start
automatically to help you activate your Internet
and Voice services.
•
If the registration process does not start
automatically:
1. Turn off security or firewall software, or give
permission to "allow the network connection" if
prompted by your browser, in order to connect
to the AT&T network.
2. Enter att.net/uverse into your address bar.
•
Continue your online registration using the
4-digit passcode you created when you placed
your order—it was mailed to you separately for
your reference.
Go Wi-Fi
4
Write down your Wi-Fi Network Name (SSID) and Wi-Fi Password (Wireless Network Key)
to configure a Wi-Fi device. This information is on the side of your Wi-Fi gateway. The
Network Name consists of "2WIRE" plus the last three digits of the Wi-Fi gateway's serial
number. Be sure to record this information in the form to the right.
Now configure your Wi-Fi network:
•
Go to your computer's Wireless Network
Settings and refresh the network list.
•
Select your Wi-Fi Network Name (SSID) from
the Wi-Fi list. You may need to scroll through
ON
the list to find your Wi-Fi Network Name.
OF F
•
Enter the 10-digit Wi-Fi Password (WPA)
in the password field to connect to
your network.
Stay connected on the go!
High Speed Internet service, so you can access the Internet at thousands of AT&T Wi-Fi Hot
Spots across the country . Visit attwifi.com to learn more.
Local Ethernet
Wireless
Phone 1
Phone 2
on the back of this guide.
Broadband
Note: If you're using an Ethernet cable
Service
for your connection, the Local Ethernet
light should blink. When you're connected
wirelessly, the Wireless light will blink.
3600HGV
2
, but will only be able to make
3
B
.
To activate your Voice
B
service to make calls:
Call 1.877.377.0016 from
the phone you set up in
Step
1 D
the voice instructions to
complete the activation.
Upon successful activation, you will
hear the following: "Your telephone
number
XXX.XXX.XXXX
successfully activated."
SN:
For Advanced Configuration: http://192.168.1.254
(optional)
System Password:
Approximate time: 10 minutes
Mac Address:
Wireless Network Key:
SSID: 2WIREXXX
Wireless Network Key: XXXXXXXXXX
For help: att.com/support
Wi-Fi Network Name (SSID)
2
W
I
R
E
10-digit Wi-Fi Password
AT&T Wi-Fi Basic is included with your AT&T U-verse
Local Ethernet
Blinking green
Wireless
Phone 1
Phone 2
Solid green
Broadband
Service
Solid green
3600HGV
(required)
, and follow
has been
Advertisement
