1. Manuals
  2. Brands
  3. Banner Manuals
  4. Accessories
  5. L-GAGE LM Series
  6. Quick start manual

Banner L-GAGE LM Series Quick Start Manual

Laser sensor
Hide thumbs Also See for L-GAGE LM Series:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
L-GAGE
LM Series Laser Sensor
®
Quick Start Guide
Laser displacement sensor that supports IO-Link communication with analog and discrete (switched) outputs.
This guide is designed to help you set up and install the L-GAGE LM Analog/Discrete Laser Sensor. For complete information on
programming, performance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at
www.bannerengineering.com
industry standards and practices.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or
death. This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized
sensor output condition.
Features and Indicators
1
2
3
Laser Description and Safety Information
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure. Do not attempt to disassemble this sensor for repair. A defective unit
must be returned to the manufacturer.
Class 2 Laser Models
CAUTION: Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid placing any
mirror-like object in the beam. Never use a mirror as a retroreflective target.
For Safe Laser Use - Class 2 Lasers
Reference IEC 60825-1:2007, Section 8.2.
Original Document
205811 Rev. B
. Search for p/n 205812 to view the manual. Use of this document assumes familiarity with pertinent
Three LED indicators provide ongoing indication of the sensing status.
1. Analog Output LED Indicator
Solid Amber = Displayed distance is within the taught analog output window
Off = Displayed distance is outside the taught analog output window
2. Power LED Indicator
Solid Green = Normal operation, power On and laser On
Flashing Green (1 Hz) = Power On and laser Off (laser enable mode)
3. Discrete Output LED Indicator
Solid Amber = Discrete Output is On
Off = Discrete Output is Off
•
Do not stare at the laser.
•
Do not point the laser at a person's eye.
•
Mount open laser beam paths either above or below eye level, where practical.
•
Terminate the beam emitted by the laser product at the end of its useful path.
27 August 2018
205811

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the L-GAGE LM Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Banner L-GAGE LM Series

Summary of Contents for Banner L-GAGE LM Series

  • Page 1 L-GAGE LM Series Laser Sensor ® Quick Start Guide Laser displacement sensor that supports IO-Link communication with analog and discrete (switched) outputs. This guide is designed to help you set up and install the L-GAGE LM Analog/Discrete Laser Sensor. For complete information on programming, performance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com .

  • Page 2: Installation Instructions

    ® L-GAGE LM Series Laser Sensor Class 2 Lasers LASER LIGHT Class 2 lasers are lasers that emit visible radiation in the wavelength range from 400 nm to DO NOT STARE INTO BEAM 700 nm, where eye protection is normally afforded by aversion responses, including the CLASS 2 LASER PRODUCT blink reflex.

  • Page 3: Mount The Device

    ® L-GAGE LM Series Laser Sensor Correct Incorrect Correct Incorrect Figure 6. Orientation for a height difference Figure 7. Orientation for a color or luster difference Figure 8. Orientation for a highly reflective target Applying tilt to sensor may improve performance on reflective targets. The direction and magnitude of the tilt depends on the application, but a 15°...

  • Page 4: Sensor Menu

    ® L-GAGE LM Series Laser Sensor from Run Mode Press > 4 sec. Access Access Sensor Menu RSD1 Menu Figure 9. Accessing the Menus Remote Display Buttons and the LM Use the RSD1 buttons Down, Up, Enter, and Escape to view or change RSD1 settings and information and to program a connected sensor.

  • Page 5: Sensor Menu (Menu)

    ® L-GAGE LM Series Laser Sensor Quick Menu The sensor includes a Quick Menu with easy access to view and change the analog and discrete output switch points. Access the Quick Menu by pressing Down or Up from Run mode. When in the Quick Menu, the current distance measurement displays on the first line and the menu name and the analog value alternate on the second line of the display.
  • Page 6 ® L-GAGE LM Series Laser Sensor Sensor Menu Full Map From Run mode, press Enter to enter the top-level menu system (A_OUT, D_OUT, INPUT, MEASURE, etc). Top Menu Sub-Menus Top Menu Sub-Menus Enter MENU A_OUT A_OUT Tch2Pt Tch2Pt Tch4mA Tch4mA 50.00mm MENU INPUT Mode INPUT Type...

  • Page 7: Specifications

    ® L-GAGE LM Series Laser Sensor Specifications Supply Voltage (Vcc) Sensing Beam 10 V dc to 30 V dc Visible red, 655 nm Power and Current Consumption, exclusive of load Sensing Range Normal Run Mode: 1.5 W, Current consumption < 62 mA at 24 V dc 50 mm to 150 mm Supply Protection Circuitry Delay at Power Up...
  • Page 8 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

Table of Contents