Table of Contents
Advertisement
Quick Links
HS-5200/5000
®
Half Pentium
•Half Size All-in-one with VGA CRT-LCD Interface•
•WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI•
•PISA/ISA Bus Industrial Single Board Computer•
HS-5200P/5000P
Half Pentium
•Half Size All-in-one •
•WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI•
•PISA/ISA Bus Industrial Single Board Computer•
TM
MMX
L/VGA I.S.B.
®
TM
MMX
I.S.B.
Advertisement
Table of Contents
Related Manuals for BOSER Technology HS-5200
Summary of Contents for BOSER Technology HS-5200
- Page 1 HS-5200/5000 ® Half Pentium L/VGA I.S.B. •Half Size All-in-one with VGA CRT-LCD Interface• •WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI• •PISA/ISA Bus Industrial Single Board Computer• HS-5200P/5000P ® Half Pentium I.S.B. •Half Size All-in-one • •WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI• •PISA/ISA Bus Industrial Single Board Computer•...
- Page 2 Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. Award is a registered trademark of Award Software, Inc. ISB is a registered trademark of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
ETTING THE 2.8 CMOS D ................14 LEAR 2.9 S DRAM................15 YSTEM EMORY 2.10 W ................15 ATCH IMER 2.11 VGA C ( HS-5200, HS-5000 ).......17 ONTROLLER ONLY A 2.12 D ............18 DDRESS ETTING 2.13 CPU T ..............18 EMPERATURE LARM 2.14 O -I/O S ............19... - Page 4 3.8 PS/2 M -DIN C ...........26 OUSE ONNECTOR 3.9 VGA C ( HS-5200, HS-5000 ) ........27 ONNECTORS ONLY 3.10 IR C ..................27 ONNECTOR 3.11 E ..............28 XTRA OWER ONNECTOR 3.12 USB P ..............28 ORTS ONNECTOR 3.13 F ( HS-5200, HS-5000 ) ....29...
-
Page 5: General Information
Industrial Single Board CPU Card. The descriptions herein are subject to HS-5200. The HS-5200P, which is based on HS-5200 but without VGA CRT-LCD, supports. The HS-5000 is based on HS-5200 but supports with ISA bus which without PCI interface at slot. The HS-5000P, which is based on HS-5000 but without VGA CRT-LCD supports. -
Page 6: Major Features
One enhanced bi-directional parallel port. Supports SPP/EPP/ECP. On board keyboard and PS/2 Mouse connector. On board SMC 37C669 super I/O. On board 32 bit PCI-BUS SVGA/ Panel controller. ( HS-5200/5000, HS-5000 only ) "DiskOnChip™" Socket Supported Memory Size up to 72 MB. -
Page 7: Specifications
1.2 Specifications ® CPU: Intel MMX™/Pentium 75~233MHz, AMD k5, k6, k6-2 350MHz, Cyrix 6x86,M2 300MHz. Bus interface: PISA bus ( HS-5200, HS-5200P ) ISA bus ( HS-5000, HS-5000P ) Chipset: SiS 5571 Data bus: 64-bit Processing ability: 64-bit Flat panel / CRT SVGA Controller: CHIP 65550 (HIQV32) Chipset with 1 MB memory support to color and monochrome Single Drive (SS) and Dual Drive (DD) STN, TFT &... -
Page 8: Delivery Package
Power supply voltage: +5V (4.75 to 5.25V), +12V / -12V power supply. Max. Power requirement: +5V @6A, +12V/-12V @20mA. Operating temperature: 0-55°C (CPU need cooler). Board size: HS-5200, HS-5200P 7.3"(L) x 5" (W) (185mm x 127mm). HS-5000, HS-5000P 7.3"(L) x 4.8" (W) (185mm x 122mm). 1.3 Delivery Package... -
Page 9: Hardware Installation
Chapter-2 Hardware Installation This chapter provides the information on how to install the hardware. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, watchdog timer, and the DiskOnChip address selection. 2.1 Caution of Static Electricity The CPU Card has been well package with an anti-static bag in protect its sensitive computer components and circuitry from the damage of... -
Page 10: Caution On Unpacking And Before Installation
2.2 Caution on Unpacking and Before Installation First of all, please follow with all necessary steps of section 2.1 in protection the CPU Card from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps: 1. -
Page 11: Hs-5200/5000'S Layout
2.3 HS-5200/5000’s Layout Default Setting：JP12 1-2 ON for HS-5000 JP12 1-2, 7-8 ON for HS-5200... -
Page 12: Quick Listing Of Jumpers
USB1 CONNECTOR CN8: PARALLEL PORT CN9: 5P KEYBOARD CONNECTOR CN10: FDD CONNECTOR CN11: INTERNAL VGA 10-PIN CONNECTOR ( HS-5200, HS-5000 only ) CN12: IR CONNECTOR CN13: 8P POWER CONNECTOR CN14: EXTERNAL VGA CONNECTOR (DB15) ( HS-5200, HS-5000 only ) CN15:... -
Page 13: Jumper Setting Description
2.6 Jumper Setting Description A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is OFF as a open circuit with a plastic cap inserted over one or no pin(s) between pins. The below figure 2.2 shows the examples of different jumper pin-set setting as ON or OFF in this manual. -
Page 14: Setting The Cpu
2.7 Setting the CPU All CPU Card provides all possibility in jumper setting for wide using all types of CPU with JP3, JP4, JP5, JP16, JP22, JP23 and JP24 setting in following. The JP1 sets the multi-times ratio of the CPU’s specification. Please reference to the following table for all type CPU in used. - Page 15 Correspond to different type CPU, it is request to set JP12 for match the CPU's Vcore operating voltage. Here shows at below of the proper jumper settings for their respective Vcore at range 2.0V to 3.5V. Voltage HS-5200 HS-5000 2.0V ALL OFF 2.1V...
-
Page 16: Cmos Data Clear
The JP22, 23, 24 used to setting the system PLL clock rate for meet with the best feature of I/O interface performance. Please set the clock rate at a necessary operating condition. An over specification setting will cause the system malfunction or un-stateable. PLL Clock setting PLL Clock JP22 JP23 JP24... -
Page 17: System Memory Dram
2.9 System Memory DRAM All CPU Card provides a wide range on-board DRAM memory by two pieces SIMM sockets (Bank0 & Bank1) to accept 1 MB, 2MB, 4MB, 8MB, 16MB, 32MB or 64MB. The SIMMs (Single In-Line Memory Modules) RAM request the access time should be 70 n-second or faster. - Page 18 JP17 : WDT Time - Out Period PERIOD *1 sec 2 sec 10 sec 20 sec 110 sec 220 sec The Watch-dog timer is disabled after the system Power-On. The watch-dog timer can be enabled by a Enable cycle with reading the control port (443H), a Refresh cycle with reading the control port (443H) and a Disable cycle by reading the Watch-dog timer disable control port (043H).
-
Page 19: Vga Controller ( Hs-5200, Hs-5000 Only )
; disable the watch-dog timer AL,DX ; get back AX, DX 2.11 VGA Controller ( HS-5200, HS-5000 only ) The C&T 655xx family supports a wide variety of monochrome and color Single-Panel, Single-Drive (SS) and Dual-Panel, Dual Drive (DD) standard and high-res passive STN and active matrix TFT/MIN LCD, and EL panels. -
Page 20: Diskonchip Address Setting
2.12 DiskOnChip Address Setting All CPU Card provides a U10 socket for install the DiskOnChip module. A JP15 may select the starting memory address of the DiskOnChip (D.O.C.) for avoid the mapping area with any other memory devices. If you have another extra memory devices in the system with the same memory, neither the CPU Card nor the extra memory devices will function normally. -
Page 21: On Board Multi-I/O Setting
JP25 DESCRIPTION Enable Disable *) : default setting 2.14 On Board Multi-I/O Setting All CPU Card provides a JP19 for enable or disable the on-board multi-I/O chipset when application of CPU temperature alarm. An Enable means that the CPU Card using the on-board multi-I/O chipset. - Page 22 JP10 : Cache RAM Mode Selection JP10 Address *OFF...
-
Page 23: Connection
Chapter-3 Connection This chapter gives all necessary information of the peripheral's connections, switches and indicators. 3.1 The Floppy Disk Drive Connector A standard 34-pin header daisy-chain driver connector provides as CN10 with following pin assignment. Total two FDD drivers may connect. -
Page 24: Pci E-Ide Drive Connector
3.2 PCI E-IDE Drive Connector Two standard 40-pin header daisy-chain driver connectors provide as CN3 & CN4 with following pin assignment. Total four IDE (Integrated Device Electronics) drivers may connect. CN3(IDE 1) : Primary IDE Connector CN4(IDE 2) : Secondary IDE Connector CN3/CN4 : IDE Interface Connector PIN NO. - Page 25 CN8 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 ACKNOWLEDGE BUSY PAPER EMPTY PRINTER SELECT AUTO FORM FEED ERROR# INITIALIZE PRINTER SELECT LN# GROUND GROUND GROUND...
-
Page 26: Serial Ports Connectors
3.4 Serial Ports Connectors All CPU Card offers two high speed NS16C550 compatible UARTs with Read/Receive 16 byte FIFO serial ports with one DB-9 external connector, and one internal 10-pin header connector. CN16 : Serial Port DB-9 Connector (ACE0) PIN NO. DESCRIPTION DATA CARRIER DETECT (DCD) -
Page 27: Keyboard Connectors
3.5 Keyboard Connectors All CPU Card offers two possibilities for keyboard connections to external PS/2 type keyboard at CN17, or an internal 5-pin header at CN9. CN9 : 5-pin Header Keyboard Connector PIN NO. DESCRIPTION KEYBOARD CLOCK KEYBOARD DATA GROUND CN17 : 6-pin Mini-DIN Keyboard Connector PIN NO. -
Page 28: External Speaker
JP6 : RESET BUTTON PIN NO. DESCRIPTION EXTERNAL RESET GROUND JP8 : IDE LED connector PIN NO. DESCRIPTION HDD ACTIVE# 3.7 External Speaker All CPU Card has an on-board buzzer. And it also provides the JP7 in allows user to connecting to the external speaker. JP7 : Speaker Connector PIN NO. -
Page 29: Vga Connectors ( Hs-5200, Hs-5000 Only )
3.9 VGA Connectors ( HS-5200, HS-5000 only ) The CPU Card provides two possible VGA connections. One standard DB-15 external VGA connector as following CN14 pin information. Another internal 10-pin header as following CN11 pin information. CN14 : 15-pin DB-15 Female VGA connector PIN NO. -
Page 30: Extra Power Connector
CN12 : 5-PIN IR CONNECTOR PIN NO. DESCRIPTION IRRX GROUND IRTX 3.11 Extra Power Connector All CPU Card provides an 8-pin extra DC power connector CN13 for internal power connection at a single board application. Please refer to the following table for detail pin information. CN13 : 8P Extra Power Connector PIN NO. -
Page 31: Flat-Panel Connector ( Hs-5200, Hs-5000 Only )
3.13 Flat-Panel Connector ( HS-5200, HS-5000 only ) The CPU Card provides a 44-pin 2.0 mm pitch header connector (CN2) for Flat-Panel connection. Please reference to the following pin-assignment for correct connection to flate panel module. +12V +12V FPVee SHFCLK... -
Page 32: Award Bios Setup
The Main Menu will be displayed at this time. Be notes that only HS-5200 and HS-5200P provides with slot extension PCI bus and ISA bus functions. And the HS-5000 and HS-5000P provides with ISA bus function only. The relative setup on PCI in the BIOS may not cause any activity to HS-5000 and HS-5000P. -
Page 33: Main Menu
4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter> to enter the sub-menu. -
Page 34: Standard Cmos Setup
4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode. -
Page 35: Bios Features Setup
4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. -
Page 36: Chipset Features Setup
4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 37: Integrated Peripherals
4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. -
Page 38: Power Management Setup
4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use.