Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BOSER Technology Industrial Single Board Computer HS-6038
Summary of Contents for BOSER Technology Industrial Single Board Computer HS-6038
- Page 1 HS-6038 Socket 370 133MHz FSB Industrial Single Board Computer •Full-size•All-in-One•CompactFlash• •133MHz FSB•CRT•Dual LAN•Audio• •ATA/33/66/100•RS-232/422/485•PC/104• •IrDA•USB•DOC•WDT•H/W Monitor• •PICMG Bus Industrial Single Board Computer•...
- Page 2 Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s).
-
Page 3: Table Of Contents
Chapter 1 General Description…………………...1 1.1 Major Features ... 2 1.2 Specifications ... 3 1.3 Board Dimensions... 4 Chapter 2 Unpacking……………………………..5 2.1 Opening the Delivery Package... 5 2.2 Inspection... 5 Chapter 3 Hardware Installation………………...7 3.1 Before Installation ... 7 3.2 Board Layout ... 8 3.3 Jumper List ... - Page 4 Chapter 4 AMI BIOS Setup……………………..27 4.1 Starting Setup ... 27 4.2 Using Setup... 28 4.3 Main Menu ... 29 4.4 Standard CMOS Setup ... 30 4.5 Advanced CMOS Setup ... 31 4.6 Advanced Chipset Setup ... 32 4.7 Power Management Setup ... 33 4.8 PCI / Plug and Play Setup...
-
Page 5: Safety Instructions
Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. -
Page 7: Chapter 1 General Description
Chapter 1 General Description ® The HS-6038 is a 133MHz FSB Intel 82815/82801BA chipset-based board designed for PICMG Bus Celeron™/Coppermine™/Tualatin™ 800MHz~1.2GHz CPU compatibility. These features combine and make the HS-6038 an ideal all-in-one industrial single board computer. Additional features include an enhanced I/O with CompactFlash, VGA, dual LAN, audio, and two COM interfaces. -
Page 8: Major Features
Additional onboard connectors include an advanced USB and IrDA ports providing faster data transmission, and a dual RJ-45 connector for 10/100 Based Ethernet use. To ensure the reliability in an unmanned or standalone system Watchdog Timer (WDT) onboard HS-6038 is designed with pure hardware that does not need the arithmetical functions of a real-time clock chip. -
Page 9: Specifications
Specifications CPU: Socket 370 for Intel Celeron/Coppermine/Tualatin 800MHz ~1.2GHz CPU Bus Interface: PICMG Bus Memory: Two DIMM sockets supporting up to 512MB ® Chipset: Intel 82815/82801BA I/O Chipset: Winbond W83627 CompactFlash: One, IDE interface adapter (optional) VGA: Intel 82815 supporting CRT display up to 1280 x 1024 at 16 colors ®... -
Page 10: Board Dimensions
Board Dimensions... -
Page 11: Unpacking
Opening the Delivery Package The HS-6038 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. - Page 12 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately.
-
Page 13: Chapter 3 Hardware Installation
Hardware Installation This chapter provides the information on how to install the hardware using the HS-6038. This chapter also contains information related to jumper settings of switch, watchdog timer, and the DiskOnChip address selection etc. Before Installation After confirming your package contents, you are now ready to install your hardware. -
Page 14: Board Layout
Board Layout... -
Page 15: Jumper List
Jumper List Jumper Definition Host Bus Clock Rate Select: 133MHz FSB Clear CMOS: Normal Operation LAN2 Enabled/Disabled Select: Enabled WDT Active Type Setting: System Reset DiskOnChip Address Select: 0D000H~ 0D1FFH JP8 / JP9 / COM 2 Use RS-232 or RS-422/485 Select: JP11 / JP12 RS-232 Connector List... -
Page 16: Configuring The Cpu
Connector PC1 / PC2 PC/104 Bus 64-pin/40-pin Connectors USB1 External USB Connector USB2/USB3 Internal USB Connectors RT1/RT2 Power Sensing Connectors VGA1 15-pin VGA Connector Configuring the CPU JP2 is used to set the Host Bus Clock Rate. The setting of internal Host Bus Clock Rate is for defining the operating clock base rate of the internal bus of core logic. -
Page 17: Ide Drive Connector
CN9: I C Bus Connector Description SMBDATA SMBCLK IDE Drive Connector IDE1/IDE2 are standard 40-pin connector daisy-chain driver connectors serving the PCI E-IDE drive provisions onboard the HS-6038. A maximum of four IDE drives can be connected to the HS-6038 via IDE1/IDE2. IDE1/IDE2: Primary/Secondary IDE Connectors Description RESET... -
Page 18: Floppy Disk Drive Connector
Floppy Disk Drive Connector The HS-6038 uses a standard 34-pin header connector, FDC1, for floppy disk drive connection. A total of two floppy drives may be connected to FDC1 at any given time. FDC1: Floppy Connector Description 3.10 Serial Port Connectors The HS-6038 offers one NS16C550 compatible UARTs with Read/Receive 16-byte FIFO serial ports. -
Page 19: Parallel Connector
CN12: RS-422/485 Connector (5x2 header) Descriptio PIN Description RTS+ CTS- JP8/JP9/JP11/JP12: COM2 Use RS-232 or RS-422/485 Select Options Settings RS-232 (default) Short 2-3 RS-422/485 Short 1-2 3.11 Parallel Connector LPT1 is a standard 26-pin flat cable connector designed to accommodate parallel port connection onboard the HS-6038. LPT1: Parallel Connector Description Strobe... -
Page 20: Ethernet Connector
3.12 Ethernet Connector The HS-6038 provides one dual RJ-45 10/100 Based LAN interface connectors. Please refer to the following table for their identical pin assignments. LAN1: Dual RJ-45 Connector PIN Description PIN Description 1TX+ 1RX+ 1R/C GND 1R/C GND 2TX+ 2RX+ 2R/C GND 2R/C GND... -
Page 21: Usb Connector
3.14 USB Connector The HS-6038 provides one 4-pin external USB connector at location USB1, and two 8-pin connectors at locations USB2 and USB3. USB1: External USB Connector Description BD0- BD0+ USB2: Internal USB Connector Description BD0- BD0+ USB3: Internal USB Connector Description BD02- BD02+... -
Page 22: Power And Fan Connectors
3.16 Power and Fan Connectors The HS-6038 provides one 5-pin ATX Power On connector at CN10, one 2-pin ATX Power ON switch at CN6, and a single 3-pin FAN out connector at CN8. CN10: 5-pin ATX Power In Connector PIN Description PS_ON VCC13 5Vsb... -
Page 23: Keyboard/Mouse Connectors
CN8 onboard HS-6038 is a 3-pin fan power output connector. CN8: Fan Power In Connector Description +12V FAN In 1 3.17 Keyboard/Mouse Connectors The HS-6038 offers two possibilities for keyboard connection. The connections are via KB1 for an external PS/2 type keyboard/mouse or via CN3 for an internal 5-pin cable converter to an AT keyboard. -
Page 24: External Speaker
CN1 and CN7 are the Keylock and Reset Button connectors onboard. CN1: Keylock Connector PIN Description Keylock CN7: 2-pin Reset Button Connector Description H/W Reset 3.19 External Speaker Aside from the buzzer at location BZ1 onboard, the HS-6038 also offers a connector (CN2) for an external speaker connection. The table below lists the pin assignments of CN2. -
Page 25: Audio Connectors
3.21 Audio Connectors The HS-6038 has an onboard AC97 3D audio interface. The following tables list the pin assignments of the CD-ROM Analog Input, the Line In and the MIC In/Audio Out connectors. CD1: CD-ROM Analog Input Connector Description CD IN_R CD REF CD REF CD IN_L... -
Page 26: Watchdog Timer
3.23 Watchdog Timer Once the Enable cycle is active, a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the period preset of WDT, it will assume that the program operation is abnormal. A System Reset signal is to re-start when such error happens. -
Page 27: Compactflash Connector
DX, 2EH AL, AAH DX, AL * User can also use AL, 00H’s defined time for reset purposes, e.g.00H for Disable, 01H = 1sec, 02H = 2sec…..FFH = 255sec 3.24 CompactFlash Connector The HS-6038 also offers an optional CompactFlash connector which is IDE interface located at the solder side of the board. -
Page 28: Pc/104 Connectors
Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. Refer to the diagram on the following page for the traditional way of inserting the card. 3.25 PC/104 Connectors The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. - Page 29 PC2: PC/104 Bus 40-pin Connector Description PIN Description MEMCS16* IOSC16* IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 DACK0* DRQ0 DACK5* DRQ5 DACK6* DRQ6 DACK7* DRQ7 MASTER* Connector diagram rotated 90 degrees clockwise from SBHE* original position LA23 LA22 LA21 LA20 LA19 LA18 LA17 MEMR* MEMW*...
- Page 30 PC1: PC/104 Bus 64-pin Connector Description PIN Description IOCHECK* IOCHRDY SA19 SA18 SA17 SA16 SA15 SA14 SA13 SA12 SA11 SA10 Connector diagram rotated 90 degrees clockwise from RESETDRV original position IRQ9 DRQ2 -12V +12V SMEMW* SMEMR* IOW* IOR* DACK3* DRQ3 DACK1* DRQ1 REFRESH*...
-
Page 31: Diskonchip Address Setting
3.26 DiskOnChip Address Setting The DiskOnChip function allows the system to boot or operate without a FDD or a HDD. DiskOnChip modules may be formatted as drive C. With DiskOnChip, user may also execute DOS commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY, DISKCOMP, etc. The U31 location onboard the HS-6038 is the DiskOnChip... - Page 32 Pin 1 Location 4. The installation is now complete and your module is now ready for use. NOTE: If you encounter difficulty installing your DiskOnChip please consult a qualified technician or engineer to perform the installation. 3.26.2 Removing DiskOnChip Modules When removing a DiskOnChip...
-
Page 33: Chapter 4 Ami Bios Setup
The HS-6038 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 34: Using Setup
Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> keys to change entries, press <F1> for help and press <Esc> to quit. The following table provides more details about how to navigate in the Setup program using the keyboard. -
Page 35: Main Menu
Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>... -
Page 36: Standard Cmos Setup
Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. -
Page 37: Advanced Cmos Setup
Advanced CMOS Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. AMIBIOS SETUP – STANDARD CMOS SETUP (C)2001 American Megatrends, Inc. All Rights Reserved Quick Boot Pri Master ARMD Emulated as Pri Slave ARMD Emulated as... -
Page 38: Advanced Chipset Setup
Advanced Chipset Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 39: Power Management Setup
Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. AMIBIOS SETUP – POWER MANAGEMENT SETUP (C)2001 American Megatrends, Inc. -
Page 40: Pci / Plug And Play Setup
PCI / Plug and Play Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 41: Peripheral Setup
Peripheral Setup The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. -
Page 42: Hardware Monitor Setup
4.10 Hardware Monitor Setup AMIBIOS SETUP – HARDWARE MONITOR SETUP (C)2001 American Megatrends, Inc. All Rights Reserved CPU Temperature Detected by CPU Temperature System Temperature Power Temperature CPU Fan Speed Chassis Fan Speed Power Fan Speed CPU VID Vcore + 5.000V +12.000V -12.000V - 5.000V... -
Page 43: Auto-Detect Hard Disks
4.11 Auto-Detect Hard Disks This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. Up to four IDE drives can be detected, with parameters for each appearing in sequence inside a box. To accept the displayed entries, press the “Y”... -
Page 44: Change Supervisor/User Password
4.12 Change Supervisor/User Password AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52 (C)2001 American Megatrends, Inc. All Rights Reserved HS-6038LV VER:1.1. Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Enter new supervisor password: _ Change Supervisor Password Auto Configuration with Optimal Settings Optimal Configuration with Fail Safe Settings Save Settings and Exit... -
Page 45: Auto Configuration With Optimal Settings
When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. -
Page 46: Optimal Configuration With Fail Safe Settings
4.14 Optimal Configuration with Fail Safe Settings When you press <Enter> on this item you get a confirmation dialog box with a message similar to the figure below. This option allows you to load/restore the default values to your system configuration, optimizing and enabling all high performance features. -
Page 47: Save Settings And Exit
4.15 Save Settings and Exit Pressing <Enter> on this item asks for confirmation: AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52 (C)2001 American Megatrends, Inc. All Rights Reserved HS-6038LV VER:1.1. Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Save current settings and exit (Y/N) ? Y Change Supervisor Password Auto Configuration with Optimal Settings... -
Page 48: Exit Without Saving
4.16 Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup without storing and having any change in CMOS. The previous selections remain in effect. This exits the Setup utility and restarts your computer. -
Page 49: Chapter 5 Software Utilities
This chapter contains the detailed information of IDE, VGA, LAN and Audio driver installation procedures. The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA, LAN and Audio drivers. The following sections describe the installation procedures of each driver based on Win 95/98, Win 2000 and Win NT operating systems. - Page 50 Click on the INTEL_ICH2 button to continue. When the IDE \ INTEL_ICH2 box appears on your screen, click on the INTEL_R&HIPSET_SOFTWARE_INS to install the IDE plug and play information files into your system.
- Page 51 Immediately after clicking the IDE button in Step 1, the program launches the InstallShield Wizard that will assist you in the installation process. Click on the Next > button to proceed. The Intel OEM Software License Agreement dialog box then appears on the screen.
- Page 52 When the Readme Information dialog box pops up, just click on the Next button to proceed. Once the InstallShield Wizard finishes updating your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot.
- Page 53 5.1.2 Installing Intel Security Driver Following Steps 1 ~ 3 of the Intel 815 chipset software (from the preceding section), click on the INTEL_SECURITY_ DRIVER button. When the dialog box below appears, make sure you close all other Windows applications then click on the Next > button to proceed.
- Page 54 When the Release Notes box pops up on the screen, read through any important information listed before clicking the Next > button. Setup will then prompt you to specify the path where you would like the Security driver installed. Select the Next > button after you have made your path/installation choice.
-
Page 55: Vga Driver Installation
Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to reboot. Only after your computer boots will the new settings take effect. - Page 56 2. When the VGA main utility window is displayed. Select INTEL_815 to continue. 3. The INTEL_815 window shows up next. Select WIN9X to invoke the corresponding installation program.
- Page 57 4. The program launches an introduction screen of what graphics driver it will install. Close all other running Windows applications then click on the Next > button to proceed. 5. Immediately after clicking on the Next > button, the Intel OEM Software License Agreement pops up on the screen.
- Page 58 6. The VGA driver utility program starts copying files needed by your Win98 to invoke the VGA capabilities. Once finishes, the system will prompt you to restart your computer. Tick on the Yes, I want to restart my computer now followed by a click on the Finish button to complete the installation.
- Page 59 2. The program launches the InstallShield Wizard for Intel 810/810E/815/815E/815EM chipset graphics. Close all other running Windows applications then click on the Next > button. 3. Immediately after clicking the Next > button, the Intel OEM Software License Agreement pops up on the screen. Choose Yes. 4.
- Page 60 5.2.3 Win NT4.0 1. Follow steps 1 and 2 from the Win9x installation procedure. When the INTEL_815 window shows up, select NT40 to invoke the installation program to your Win 2000 OS. 2. The program launches an introduction screen of the graphics it will install.
-
Page 61: Lan Driver Installation
LAN Driver Installation 5.3.1 Win 95/98 Right click on My Computer icon then scroll to the Properties item from the pop-up menu. Select Device Manager from the top menu bar. A list of all devices installed appears, scroll down to the Other devices and then select on PCI Ethernet Controller. - Page 62 Once the PCI Ethernet Controller Properties screen pops up on the screen, click on the Update Driver … button to launch the Update Device Driver Wizard screen. The succeeding screen then lets you choose whether to search for a better driver for the LAN or display the available list of drivers. Select Search for a better driver than the one your device is using now followed by a click on the Next >...
- Page 63 The wizard program will then require you to specify the location of the driver file. Tick on the Specify a location: and type or select the path where the driver files exist (c:\i82562). Click on the Next > button to proceed.
- Page 64 The program now starts copying the file(s) needed by your Win98. When the program fails to seek for 8255xDel.exe file from your specified location, it will prompt you to specify the path where the Intel Pro Adapter exists. With the Utility CD Disk on your CD drive, key in d:\win98_se\setup\win98 on the blank space below Copy files from: then press the OK button.
- Page 65 When the program finishes updating and copying files for the Intel Pro/100VE Network Connection, click on the Finish button to proceed. For the new hardware settings to take effect and to complete the installation process, you must restart your computer when the System Settings Change window below pops up.
- Page 66 5.3.2 Win 2000 Right click on My Computer icon and then scroll to the Properties item from the pop-up menu.
- Page 67 When the System Properties window pops up on the screen, click on the Device Manager button. A list of all devices installed appears, scroll down to the Other devices and then right click on Ethernet Controller to select the Properties button. Refer to the following screen shot for a clearer explanation of this step.
- Page 68 Once the Ethernet Controller Properties screen pops on the screen, click on the Update Driver … button to launch up the Update Device Driver Wizard screen. Once the Upgrade Device Driver Wizard screen pops up on the screen, click Update Driver … to launch the Win 2000 driver installation program.
- Page 69 6. The wizard will then inform you the unknown device it detected from the system. Since the Win2000 driver list does not include Intel chip driver onboard HS-6038, tick Search for a better driver than the one your device is using now followed by a click on the Next >...
- Page 70 8. The wizard program will then require you to insert the manufacturer disk at your specified location (entered at the Copy manufacturer’s files from: space) of the driver file. With your Utility CD disk inserted in the drive, type d:lan\i82562 then click on the OK button to proceed.
- Page 71 10. When the program finishes updating and copying files for the Intel Pro/100VE Network Connection, click Finish to proceed. 11. For the new hardware settings to take effect and to complete the installation process, you must restart your computer when the System Settings Change window below pops up.
- Page 72 The Network Configuration dialog box then appears, notifying the user that there is no Windows NT Networking available. Click on the Yes button to start the installation process. The Network Setup Wizard will then ask you to identify the network connection of your computer. Select Wired to the network and click on the Next >...
- Page 73 The succeeding screen then indicated that the wizard will initially search for Network Adapter from the available list of drivers. Select on Start Search. When it is done searching for available network drivers, the wizard will show a list and allow you to locate and choose the appropriate Network Adapter.
- Page 74 The wizard program will then require you to insert the manufacturer disk and specify the location of the driver file (i.e., c:\i82562). Click on the OK button to proceed. The Select OEM Option then appears, prompting you to select the software supported by the network hardware device you will install.
- Page 75 The wizard program now displays on the screen that it has detected the Intel() PRO Adapter. Click on the Next > button to continue installing. The wizard program now prompts you to specify the networking protocols used on your network structure. Tick on the TCP/IP Protocol and click on the Next >...
- Page 76 10. The next screen will allow you to customize the Network Services the wizard program intends to install. Tick services as needed and then click on the Next > button to continue. 11. The Network Setup Wizard then prompts you that it is ready to install the network components based on your selection.
- Page 77 12. The Network Setup Wizard will then need to copy the drive file(s). Specify the path of your device driver(s) (i.e., d:\i386) and click the Continue button. 13. Choose the default entry, No, when the following screen pops up on the screen.
- Page 78 14. If you need to disable network bindings on the network services installed, select the service and then click on the Disable button. Otherwise, proceed by clicking on the Next > button. 15. Select which member (Workgroup or Domain) you belong to. Click on the Next >...
- Page 79 16. The wizard program then informs you that Networking is now installed on your system. You must restart your computer to make the setting changes take effect. Click on the Finish button to close the wizard program. 17. When the following dialog box pops up on your screen, click on the Yes button to restart your computer and make the setting changes take effect.
-
Page 80: Audio Driver Installation
Audio Driver Installation 5.4.1 Win 95/98 After loading the Utility CD-ROM, the program automatically runs the utility. Press Enter to proceed installing. When the main utilities window pops up on the screen, select SOUND&AC7. The succeeding screen will then show you the SOUND&AC97 main menu. - Page 81 Select the language you intend to use for the installation. The default is English. After making your choice, press on the OK button to proceed. Once the InstallShield Wizard completes the operation and update of your AC’97 driver, it will ask you to remove disks from their drives, and prompt you to restart your system.
- Page 82 5.4.2 Win 2000 Following steps 1 and 2 of the Win95/98 AC97 installation, select WIN2K button when the ALC100 dialog box appears on the screen. Select the language you intend to use for the installation. The default is English. After making your choice, press on the OK button to proceed.
- Page 83 Once the InstallShield Wizard completes the operation and update of your AC’97 driver, it will ask you to remove any disks from their drives, and prompt you to restart your system. Tick on the Yes, I want to restart my computer now. Afterwards, click on the Finish button to complete the installation process.
- Page 84 5.4.3 Win NT Following steps 1 and 2 of the Win95/98 OR step 1 of Win 2000 AC97 installation, select WINNT button when the ALC100 dialog box appears on the screen. Select the language you intend to use for the installation. The default is English.
- Page 85 Once the InstallShield Wizard completes the operation and update of your AC’97 driver, it will ask you to remove any disks from their drives, and prompt you to restart your system. Tick on the Yes, I want to restart my computer now. Afterwards, click on the Finish button to complete the installation process.
- Page 86 This page intentionally left blank.