Sony VENICE MPC-3610 Operating Instructions Manual page 41

000 41
3. Camera Operations: Menu Operations
Monitoring category
Default values are shown underlined and in
[Notes]
ˎ The unit supports independent configuration of Info and Frame Line for each system. The display information for the A and ˎ
B output images is configured using the Monitoring menu (page 52).
ˎ Info and Frame Line may not be displayed depending on the Output Format setting. In this case, "–" is displayed and the ˎ
setting cannot be changed.
Item Settings
VF Info A/B/Off
Frame Line A/B/Off
SDI 1/2 Output The available settings vary
Format according to the imager
mode, project frame rate, and
SxS recording format settings.
Info –
Frame Line A/B/Off
SDI 3/4 Output The available settings vary
Format depending on the SDI 1/2
[Note]
setting.
Depending on the
Output Format setting Info A/B/Off
of SDI 1/2, the Output
Format, Info, Frame
Frame Line A/B/Off
Line settings of SDI
3/4 may be blank and
cannot be changed.
Monitor Output The available settings vary
Format depending on the SDI 1/2
setting.
Info A/B/Off
Frame Line A/B/Off
HDMI Output The available settings vary
Format depending on the SDI 1/2
setting.
bold text.
Description
Selects the information to display
superimposed on the viewfinder image.
Selects the frame lines to display
superimposed on the viewfinder image.
Selects the SDI 1/2 output format.
Information display is not superimposed
on the SDI 1/2 output.
Selects the frame lines to display
superimposed on the SDI 1/2 output.
[Note]
Frame lines are only superimposed if the
output format is 4K/QFHD.
Selects the SDI 3/4 output format.
Selects the information to display
superimposed on the SDI 3/4 output.
Selects the frame lines to display
superimposed on the SDI 3/4 output.
Selects the Monitor output format.
Selects the information to display
superimposed on the Monitor output.
Selects the frame lines to display
superimposed on the Monitor output.
Selects the HDMI output format.
Item
Moni. Details
(ITEM key 6)
1) For details about formats available for selection, see "SDI OUT Connector Output Formats" (page 76).
2) For details about formats available for selection, see "MONITOR OUT Connector/HDMI OUT Connector Output Formats"
(page 79).
Audio category
Default values are shown underlined and in
Item Settings
1)
Source Switch LINE / AES/EBU / MIC
CH-1 Audio Level Auto/Manual
–99 to
CH-2 Audio Level Auto/Manual
–99 to
1) MIC Reference –60dB/–50dB/–40dB
Monitor CH When Monitor Output CH Pair
is set to CH-1/CH-2
CH-1/CH-2, CH-1, CH-2
When Monitor Output CH Pair
is set to CH-3/CH-4
CH-3/CH-4, CH-3, CH-4
0
Monitor Level to 99
2)
CH1 Level Meter –
CH2 Level Meter –
CH3 Level Meter –
CH4 Level Meter –
Audio Details
(ITEM key 6)
2)
Settings Description
Displays the contents of the Monitoring
menu (page 52) in the full menu.
bold text.
Description
Displays the position of the AUDIO IN switch
(page 8) that sets the CH1 and CH2 input
source.
The audio recording level is adjusted
±0 to +99 automatically when set to Auto.
The audio recording level is adjusted manually
when set to Manual.
The audio recording level is adjusted
±0 to +99 automatically when set to Auto.
The audio recording level is adjusted manually
when set to Manual.
Selects the reference input level of the
microphone.
Selects the audio channel that is output to the
headphones and speaker.
Adjusts the monitor audio level.
Displays the CH1 level meter.
Displays the CH2 level meter.
Displays the CH3 level meter.
Displays the CH4 level meter.
Displays the contents of the Audio menu
(page 55) in the full menu.