Advertisement
EN
Installation manual for control panel for automations with two 230 V~ motors with built-in radio.
F1
Power supply
DITEC S.p.A.
Via Mons. Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY
Tel. +39 02 963911 - Fax +39 02 9650314
www.ditec.it - ditec@ditecva.com
RF
L N
U W V
X Z Y
230V~
230V~
Motor 1 Motor 2
E2
PRG
ANT
SIG
JR1
COM
BIXMR2
B
ON
OFF
1 2 3 4 5 6
ON
OFF
TR
R1
TC TM
15 13 12 11 0 1 1 5 6 8 9
IP1935EN
rev. 2010-07-19
GOL4
A
1 2 3 4
IN
11
12
SA
POWER
Advertisement
Related Manuals for DITEC E2J
Summary of Contents for DITEC E2J
- Page 1 15 13 12 11 0 1 1 5 6 8 9 POWER 230V~ 230V~ Motor 1 Motor 2 Power supply DITEC S.p.A. Via Mons. Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY Tel. +39 02 963911 - Fax +39 02 9650314 www.ditec.it - ditec@ditecva.com...
-
Page 2: Table Of Contents
INDEX Subject Page eneral safet precautions EC declaration of conformit Technical data 3.1 Applications Connection of power suppl Commands Outputs and accessories Adjustments Radio receiver operation Start-up 10. Troubleshootin 11. Example application for ates with one swin in door win 12. - Page 3 GENERAL SAFETY PRECAUTIONS This installation manual is intended for professionall competent personnel onl . The installation, the power connections and the settin s must be completed in conformit with or in Methods and with the re ulations in force. Before installin the product, carefull read the instructions. Bad installation could be ha ardous. The pac a in materials (plastic, pol st rene, etc.) should not be discarded in the environment or left within reach of children, as these are a potential source of ha ard.
-
Page 4: Ec Declaration Of Conformit
Degree of protection Memorizable radio codes 433,92 MH Radio frequency NOTE: the given operating and performance features can only be guaranteed with the use of DITEC accessories and safety devices. 3.1 Applications CONNECTION OF POWER SUPPLY Fix the control panel permanentl . Pass the cables alon from the lower side of the container. -
Page 5: Commands
COMMANDS Command Function Description N.O. STEP-BY-STEP With DIP1A=OFF and TC MA , the closin of the contact acti- WITH AUTOMATIC vates openin or closin operations in the followin se uence: CLOSING open-stop-close-open. NOTE: the stop is not permanent but lasts for a duration set by TC. -
Page 6: Outputs And Accessories
OUTPUTS AND ACCESSORIES Output Value - Accessories Description Accessories power supply. Power suppl output for external ac- cessories, includin automation status lamp. 24 V= / 0,5 A Open automation lamp. Onl with the 0-11 limit switch (N.C.) con- 24 V= / 3 W nected and DIP3B=OFF the li ht switches off when the automation is closed. -
Page 7: Adjustments
ADJUSTMENTS Description Step-b -step. Openin . DIP1A Command 1-5 operation. NOTE: it also sets operating mode of the plugin cards connected on AUX. 100% DIP2A Restore automatic closing time. Open. Closed. DIP3A Automation status at power on. Indicates how the control panel considers NOTE: with limit switches NOTE: if the automatic clo- automation when powered up. - Page 8 Trimmer Description Power adjustment. Adjusts the volta e supplied to the motor. Setting motor 1 (M1) closing delay time. From 0 to 30 s. When closin , motor 1 (M1) arrives after a dela set with trimmer TR relative to motor 2 (M2).
-
Page 9: Radio Receiver Operation
RADIO RECEIVER OPERATION The control panel is e uipped with a radio receiver with a fre uenc of 433.92 MH . The antenna consists of a 173 mm lon ri id wire. It is possible to increase the ran e of the radio b connectin the external antenna of the ashin li hts, or b installin the tuned antenna (BIXAL). -
Page 10: Troubleshootin
10. TROUBLESHOOTING Problem Possible causes Remedy The automation does not No power. Chec that the control panel is powe- open or close. (POWER led off). red correctl . Short circuited accessories. Disconnect all accessories from termi- (POWER led off). nals 0-1 (volta e must be 24 V=) and reconnect one at a time. - Page 11 11. EXAMPLE APPLICATION FOR GATES WITH ONE SWINGING DOOR WING DIP3B=OFF 1 2 3 4 5 6 R1<MAX When the control panel is used in applications with TM<MAX one swin in door win , one of the followin operatin 1 2 3 4 R1 TM modes ma be selected: (Fig.
- Page 12 (Fig. 11.4) Door wing stops against mechanical stops and inverts in the event of obstacle detection. Set an operatin time of 2-3 s lon er than the ef- DIP3B=OFF fective time ta en b the door win (TM MAX) and 1 2 3 4 5 6 position the proximit limit switches 2-3 s ahead of R1<MAX...
- Page 13 12. EXAMPLE APPLICATION FOR GATES WITH TWO SWINGING DOOR WINGS TR>3 s R1<MAX TM<MAX R1 TM When the control panel is used in applications with two overlappin swin in door win s, one of the followin 15 13 12 11 0 1 1 5 6 8 9 operatin modes ma be selected: (Fig.
- Page 14 (Fig. 12.4) Door wings stop against mechanical stops and invert in the event of obstacle detection. Set an operatin time 2-3 s reater than the effective TR>3 s time ta en b the door win s (TM MAX) and connect R1<MAX TM<MAX the closin proximit switch N.O.
-
Page 15: Hold-To-Run Function Mode
13. HOLD-TO-RUN FUNCTION MODE DIP5B=OFF 1 2 3 4 5 6 NOTE: to use the control panel in hold-to-run NOTE: to use the control panel in hold-to-run R1<MAX DIP1A=ON TM=MAX mode, disconnect terminal 9. mode, disconnect terminal 9. 1 2 3 4 In this case, the openin command (1-5) and the closin R1 TM command (1-6) operate onl if ept pressed, if released... - Page 16 DITEC ESPAÑA ARENYS DE MAR Tel. +34 937958399 Fax +34 937959026 www.ditecespana.com DITEC FRANCE MASSY Tel. +33 1 64532860 Fax +33 1 64532861 www.ditecfrance.com DITEC GOLD PORTA ERMESINDE-PORTUGAL Tel. +351 22 9773520 Fax +351 22 9773528/38 www. oldporta.com DITEC SVIZZERA BALERNA Tel.
Need help?
Do you have a question about the E2J and is the answer not in the manual?
Questions and answers