Page 1
• FEET-ADJ-UNV-2430# **PATENT PENDING** MAX Load 265 lbs (120 KG) Equally Divided MAX Load 175 lbs (80 KG) Per Column CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! FLEXRISE2 = Manual-ESI-1510-01-160328vA (A4) Reduce.Reuse.Recycle...
Page 2
IMPORTANT INFORMATION Always make sure all screws are tightened before use of the frame for desk. Duty cycle of the frame for desk is 10%, max. 2 minutes operating / min. 18 minutes stop. Maximum load of the frame for desk is 265 lbs (120 kg), equally divided. Ensure the loading on each column is less than 175 lbs (80 kg).
TROUBLE SHOOTING GUIDE ISSUE INSPECT SOLUTIONS Connect plug to main power supply to make sure the Is the power cable connected voltage is ok. to the main power supply with correct voltage? If not then try to connect another device (ex lamp) to check.
HANDSET PROGRAMMING SET UP SYNCHRONIZATION (KY0 and KY4) 1. Once you have fully assembled your desk. It needs to be synchronized at the lowest position. 2. Ensure there are not obstructions for the desk to move vertically 3. Press and hold the “UP and DOWN” arrow buttons at the same time. 4.
PARTS LIST Ships in Box 2 Qty: 2 Qty: 2 Qty: 1 Qty: 1 Qty: 1 Qty: 1 Machine Screw Cable Management Clip M6 x 10mm Qty: 1 Qty: 4 Qty: 8 Machine Screw Wood Screws Wood Screws M10 x 20mm M5 x 18mm M4 x 25mm Qty: 8...
Page 6
STEP 2 – CROSS BAR WIDTH 64 in 54 in 44 in 34 in 44 in 54 in 64 in 34 in to 64 in 19.5 in to 23.5 in...
Page 7
STEP 1-3 – CROSS BAR and END SUPPORT BARS Unscrew Side Leveling Screws with Allen Wrench (P) to Expand Cross Bar and Tighten once Adjusted to Correct Width STEP 1 STEP 3 STEP 2 Unscrew Bottom Cross Bar Machine Screws and Adjust to Length STEP 3 Unscrew End Support Machine Screws and Extend from...
Page 8
STEP 4-5 – LEG COLUMN STEP 4 Secure with Machine Screws on Cross Bar with Allen Wrench (N) Secure Leg Column (B) with STEP 5 Machine Screws (I) using Allen Wrench (O)
Page 9
STEP 6-7 – FEET LENGTH STEP 6 Remove Adjustable Plate for 22 in (559 mm) Length STEP 9 Remove Machine Screws and Secure After Adjusting Length STEP 7 STEP 9 Adjust Leveling Pads 22 in (559 mm) 28 in (711 mm)
STEP 12-14 – CONTROL UN IT OPTION 1 or OPTION 2 STEP 12 and Secure with Machine Screws (M) STEP 14 Secure with Wood Screws (K) x 2 pcs OPTION 1 RIGHT SIDE OPTION 2 LEFT SIDE STEP 13 Insert Control Box (C) to Control Box Bracket (G) Work Surface...
Page 14
STEP 15 – HANDSET Work Surface Do Not Over Tighten Install Handset (D) onto STEP 15 Work Surface with Wood Screws (L)
Page 15
STEP 16-17 – CONTROL BOX WIRES / CABLE MANAGMENT STEP 17 Route Wires to Cable Management Clips Pre-Installed STEP 16 Plug in all Wires to Control Box (C) Make Sure All Connections are STEP 17 Secure Route Wires to Cable Management Clips...
Page 16
NEED HELP? PLEASE CONTACT Phone: 1-800-833-3746 Email: customerservice@esiergo.com Web: www.esiergo.com ESI Ergonomic Solutions...