Advertisement
7. Shutdown mode
This mode shuts down your heating system.
Turn the selector dial to
.
Room
temperature
Configuration menu
access button
(press and hold for
5 seconds)
8. Set-point Temperature Setting
Turn the selector dial to
.
Adjustment of the Comfort
set-point temperature (from 5
to 30°C in increments of 0.5°C)
Confirm switch to Setback
temperature setting
Adjustment of the Setback
set-point temperature (from 5 to
30°C)
Confirm
To exit this mode, turn the
selector dial.
10. Programming
4. Check your program
Press the
button repeatedly to check the accuracy
of the Comfort and Setback periods you created.
Time slot
consulted
Program
Verification of the
profile
different
periods
Press OK to check the next day.
To exit the mode, turn the selector dial to another
mode.
COMMENTS: Depending on the configuration made
during installation, programming can be weekly or
daily. Likewise, this programming may be done in
increments of one hour, 30 minutes, or 15 minutes.
To change these settings, refer to the installation
section of these instructions, or contact our customer
service department or your installer.
9. Setting the time
Turn the selector dial to
.
The days flash.
Press + or - to change the day, then press OK
to confirm and continue on to the next setting.
Minutes
Days
(1: Monday...
7: Sunday)
Hours
Repeat the operations to set the hours and minutes.
To leave the "setting the time" mode, turn the selector
dial.
11. Information button
i i
In AUTO mode, pressing the
button gives you the
temperature of the room or the set-point temperature
according to the installation configuration.
If your thermostat displays the temperature of the room
or
Set-point temperature display
Return to normal display
(automatic after 2 minutes)
10. Programming
Turn the selector dial to PROG.
The default program is a Comfort period from 6:00
to 23:00.
1. Create your program
Programming starts on day 1 at midnight.
Press the
or
buttons to create different Setback
or Comfort periods.
Comfort period
Day
adjustment
Setback period
adjustment
1st time slot
2. Confirm and copy the program
Press and hold the OK button for 3 seconds to
confirm the program you created and copy it to the
next day.
OR
3. Confirm the program
Press the OK button to confirm and continue on
to the next day to program it separately.
12. Replacing batteries
(version TYBOX 710-713)
Battery level symbol
When the battery level symbol
appears, you have around
1 month to change the batteries
(two 1.5 V alkaline batteries,
LR03 or AAA).
Replace the batteries,
2
making sure they are
1
Separate the thermostat
the right way round
from its
support
3
4
Lock the thermostat
Position the thermostat
on its base
The following precautions must be respected:
- Ensure that the +/- polarities are correctly placed
when the battery is fitted into the unit.
- Do not dispose of used batteries in unauthorized
places (you should respect the environment by
taking the batteries to a suitable collection site).
- Do not recharge the batteries.
- You have approximately 30 seconds to change
the batteries before the time is reset to zero
(if this happens, reset the date and time).
E.g. Comfort from 6:00 to 8:00 and from 17:00 to 23:00
0h
6h
8h
17h
23h
0h
Press and hold
Press and hold
until you reach 06:00
until you reach 23:00
Press and hold
Press and hold
until you reach 08:00
until you reach 00:00
Press and hold
Copy and confirm
until you reach 17:00
or simply confirm
13. Troubleshooting
Nothing is displayed on the room unit screen.
There is no power supply or batteries.
Check your circuit breaker or your batteries
The unit is in time setting mode.
There was a mains disruption that lasted more than 2 hours.
Set the time. All other settings have remained unchanged.
When setting the time,there is no option to set the day.
You are in daily programming.
To switch to weekly programming, refer to the installation
section of these instructions, or contact your installer or our
customer service department.
When creating a program,the
and
symbols do
not appear on the screen.
Changing programs is not allowed.
Refer to the installation section of these instructions, or
contact your installer or our customer service department.
The temperature displayed does not match the
temperature measured in the room (thermometer).
Refer to the installation section of these instructions or
contact your installer or our customer service department.
The programs cannot be modified and set-point
temperature adjustment is limited (Comfort:16 to 22°C,
Setback:13 to 19°C, Frost Protection:5 to 11°C)
Refer to the installation section of these instructions or
contact your installer or our customer service department.
Your heating system is in Frost-Protection mode.
The thermostat is in
,
, PROG o
position.
Advertisement
