DELTA DORE RADIO TYBOX User Manual

User guide

RADIO TYBOX
Wireless programmable thermostat
1-zone pack or 2-zone pack
DELTA DORE - Bonnemain
35270 COMBOURG - FRANCE
E-mail: deltadore@deltadore.com
Device compliant with the requirements of directives:
R&TTE 1999/5/CE
Because of changes in standards and equipment, the characteristics
given in the text and the illustrations in this document are not binding
unless confirmed by Delta Dore.
Absence mode
This mode lets you place your home under Frost
Protection if you need to leave for several days.
Turn the knob to .
Adjustment of the number of days (1 to 365)
E.g. For a departure on 1 March and a return
on 16 March, program 15 days of absence.
Automatic operation will resume on
16 March at midnight.
Confirm
Set-point temperature setting (from 5 to 15°C)
Confirm and start the calendar countdown.
Return to AUTO mode at
the end of the countdown
To make changes to the current absence mode,
press OK once more.
Warnings
• Carefully read these instructions prior to use.
• Do not attempt to repair the unit yourself;
an after-sales service is available.
Override
In automatic mode, override is used to switch from
Comfort to Economy mode (or conversely) until the
next program change.
E.g. It is 15:30 and you would like to switch to Comfort
mode before the set time (17:00).
00:00 6:00 8:00 15:30 17:00 23:00
Current day programming
Press the override button
Override
currently active
To cancel the current override, At 17:00, the program will
press the button once more. return to its usual program.
Off Mode
This mode shuts down your heating system.
Turn the knob to .
Room
temperature
Programming
Turn the knob to PROG .
The default program is a Comfort period from
6:00 to 23:00.
1. Creating your program
Programming starts on day 1 at midnight.
Press the or buttons to create different Economy
or Comfort periods.
Day
Comfort period
adjustment
Economy period
adjustment
1st time
slot
2. Confirming and copying the program
Press and hold the OK button for 3 seconds to confirm
the program you created and copy it to the next day.
OR
3. Confirming the program
Press the OK button to confirm and continue on to the
next day to program it separately.
Presentation
This manual is for the RADIO TYBOX transmitter.
1-zone pack (1 transmitter)
2-zone pack (2 transmitters)
This thermostat lets you program your heating system
to Comfort or Economy mode.
Selector
knob position
Off mode
Absence mode
Timer mode
Automatic mode
Timer mode
This mode is used to choose a set-point temperature
for a given amount of time. Turn the knob to
Adjustment of the duration from 15 minutes
to 72 hours (in increments of 15 minutes)
Confirm
00:00
Set-point temperature setting (from 5 to 30°C)
Confirm
To make changes to the current timer mode,
press OK once more.
To cancel the current timer mode, turn the knob.
Set-point temperature setting
Turn the knob to .
Comfort set-point temperature setting
(from 5 to 30°C in increments of 0.5°C)
Confirm
Go on to temperature setting
Economy
Adjustment of the Economy temperature
setting (from 5 to 30°C)
Confirm
To exit this mode, turn the knob.
Depending on the system configuration (menu 1-08),
"conf" may be displayed for the
temperature.
This set-point temperature cannot be modified.
If this is the case, the Comfort set-point temperature
can be adjusted on your heat emitter (convector, panel
heater, thermostatically controlled valve, etc.).
E.g. Comfort from 6:00 to 8:00 and from 17:00 to 23:00
00:00 6:00 8:00 17:00
Press and hold
until you reach 06:00
Press and hold
until you reach 08:00
Press and hold
until you reach 17:00
Automatic mode
AUTO.
Turn the knob to
Your thermostat will function according to the program.
Current day
Heating
Modification
demand mode
buttons
Current day
programming
Display in automatic mode
Selector
knob
NOTE: Depending on the configuration during
installation, your unit will continuously display the
set-point temperature or the room temperature.
To change these settings, refer to the "installation
Continuous mode
guide", or contact our customer service department
Time setting or your installer.
Programming
Set-point temperature
adjustment
Continuous mode
This mode is used to choose a set-point temperature
that remains constant.
.
Turn the knob to .
Set-point
temperature
To exit this mode, turn the knob.
Return to AUTO mode at
the end of the countdown
Time setting
Turn the knob to .
The days flash.
Press + or - to change the day, then press OK to
confirm and continue on to the next setting.
Days
(1 : Monday ...
7 : Sunday)
Hours
Repeat the operations to set the hours and minutes.
To leave the "time setting" mode, turn the knob.
NOTE: If the unit is configured for a daily program,
set-point
the days setting is not offered.
Checking your program
23:00 00:00
Press the button repeatedly to check the accuracy
of the Comfort and Economy periods you created.
Time slot
consulted
Program
Press and hold
profile
until you reach 23:00
Press OK to check the next day.
Exiting the programming mode
NOTE: Depending on the configuration made during
Press and hold
installation, programming can be weekly or daily.
until you reach 00:00
Likewise, this programming may be done in increments
of one hour, 30 minutes, or 15 minutes. To change these
settings, refer to the "installation guide", or contact our
customer service department or your installer.
Turn the knob to another mode.
Copy and confirm
or confirm
Time Current mode
Override
Room
temperature
Information
button
Choice of set-point
temperature (from 5 to 30°C)
Confirm
Modification of the set-point
temperature
Minutes
Verification
of the different
or periods