Page 1
OPERATING MANUAL Model Number GBE104v2.2 10.4 inch Digital Photo Frame...
Page 2
Quick Start Guide GBEDIGITAL model number GBE104v2.2 This page gives you basic information for setting up your digital photo frame and showing pictures. For more detailed instructions and safety instructions, see the Operating Manual booklet included with your digital photo frame.
Table of Contents DISCLOSURES..................................4 IMPORTANT SAFETY INSTRUCTIONS..........................6 TECHNICAL SPECIFICATIONS ............................7 BOX CONTENTS ..................................7 THE DIGITAL PHOTO FRAME............................8 THE REMOTE..................................9 GETTING STARTED................................10 .........................10 ETTING UP YOUR DIGITAL PHOTO FRAME ........................10 NSERTING AND EMOVING EDIA ARDS ’ ......................11 NSTALLING OR HANGING THE EMOTE ATTERY BASIC OPERATIONS ................................11...
GBEDIGITAL reserves the right to make changes and/or improvements to the products and programs described in these Operating instructions at any time without notice. GBEDIGITAL and its distributors or agents assume no responsibility for errors or omissions in these Operating Instructions, and do not make any commitment to update the information contained herein.
Page 5
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important Safety Instructions Warning: Warning: To reduce the risk of fire, electric To reduce risk of electric shock, do shock or product damage, do not not open the digital frame case and expose the digital frame to rain, do not remove screws from the frame moisture, dripping or splashing of case.
The Digital Photo Frame Figure 1 – Front View Figure 2 – Rear View Wall Mount Holes Receiver Sensor Back Stand Figure 3 Figure 3 – Side View 1 SLAVE: (Mini USB 5-Pin port) – connects to PC in order to send or receive files from the digital photo frame’s internal memory.
Figure 5 1. A/V OUT 2. EARPHONE The Remote The diagram below shows the digital photo frame’s remote, with control buttons. The battery type is Lithium 3V (CR2025). Remote Symbols • LEFT, RIGHT, UP DOWN buttons, respectively: • Play/Pause button: •...
Getting Started Setting up your digital photo frame 1. Remove the contents from the box. 2. Review the Safety Instructions on page 5. 3. Remove the protective plastic sheeting from the LCD screen. 4. Install the Back Stand by placing it on the aperture and turning it clockwise. View diagram below for more information.
• Do not force cards into the slot. If the card does not slide easily into the slot, make sure that you are inserting the card into the correct slot and make sure the card is facing the correct direction. •...
4. Select the file you would like to display by using the UP or DOWN arrow buttons and press ENTER. (There may be several subfolders. You may have to press the ENTER key more than once to get to your picture files). 5.
Combo - (Displaying images and music simultaneously) 1. Go to the main menu by pressing the MENU button on your remote until the main menu appears. 2. Use the LEFT or RIGHT arrow button until the COMBO option is selected on your screen and press ENTER.
2. Use the LEFT or RIGHT arrow button until the TEXT option is selected on your screen and press ENTER. 3. On the next screen, you will have an option between internal Memory and your memory card drive. Using the LEFT or RIGHT arrow buttons from your remote, select the drive you would like to use and press the ENTER button.
Language Settings: • Press ENTER to highlight then make your selection using the UP or DOWN arrows then, confirm your selection by pressing ENTER. Press the LEFT to go back to the menu. Slideshow Settings: • Press ENTER to highlight the section then make your selection using the UP DOWN arrows.
Color Settings: Press ENTER to highlight the section then use the UP or DOWN arrow to navigate the sections. Using LEFT or RIGHT arrow buttons will change your settings on highlighted section. Factory Reset: • Press ENTER to highlight the section then press the ENTER key on your remote to reset.
NOTE: Depending on the image size and resolution, it may take up to 12 seconds for each thumbnail to appear. For optimal performance, use the recommended resolution of 800 x 600 pixels. HOST Mode – (Using your digital photo frame with an external USB card reader) 1.
AUDIO OUT / VIDEO OUT - Mode You can connect your digital frame to an external device (i.e., TV) to display your media from your digital photo frame. 1. With the digital frame switched off, use the AV cables included with your device. Plug the cables into the A/V OUT jacks located on the bottom edge of the digital frame.
6. Using your mouse- right click “New” then choose a “Folder”; while folder is highlighted you might want to rename your newly created folder. “New Folder” to “John’s Birthday”. You can create more than one folder at this time. 7. To add files, you can drag the desired picture files from your computer onto the Photo Frame internal memory drive folder.
Delete) 7. Choosing 2 option from the menu using DOWN arrow key and using ENTER key will paste your music file into internal memory or specific folder previously created. IMPORTANT NOTE: Once you complete copying your files you must RESTART your digital photo frame.
Troubleshooting Digital frame does not power on • Make sure the power is securely connected to the digital frame and to a working electrical outlet. • Check that the power switch on the side of your panel is switched ON. Remote does not work •...
I can not rotate an image the way I want to • The remote’s ROTATE button alternates between rotating the images horizontally and vertically. To return an image to its original position, you will have to click the ROTATE button four times to cycle through to the original orientation. •...
Page 23
A: Send an email to: support@gbedigital.com Need help? Call our customer support line at (877) 595-2040 or email us cs@gbedigital.com. Operators are available between 9 a.m. and 5 p.m. CST, Monday through Friday. Calls received after office hours will be returned the...
If the product does not work properly due to defect in materials or workmanship, GBEDIGITAL (collectively refereed to as “the warrantor”) will, for the period of one year from the date of purchase (“Limited Warranty Period”), at its option either (a) repair it, or (b) replace it with a new or refurbished product.
Page 25
Limited Warranty period, you may contact your dealer or service center. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the address listed for the warrantor. For more information: WWW.GBEDIGITAL.COM General Questions: info@gbedigital.com Customer service: cs@gbedigital.com Product Support: support@gbedigital.com...