Connecting to a TV that has no Audio
/Video Input Jacks
•
You can connect your camcorder to a TV through a VCR.
1. Connect the camcorder to your VCR with the Audio/Video cable.
•
The yellow jack: Video
•
The white jack: Audio(L) - mono
•
The red jack: Audio(R)
2. Connect a TV to the VCR.
3. Set the Select switch to TAPE.
(SC-D383/D385 only)
4. Press the MODE button to set
Player (
).
5. Turn on both the TV and VCR.
•
Set the input selector on the
VCR to line.
•
Select the channel reserved
for your VCR on the TV set.
6. Play the tape.
Playback the tape
1. Connect a power source.
2. Insert the tape you wish to play back.
3. Set the Select switch to TAPE. (SC-D383/D385 only)
4. Press the MODE button to set Player (
5. Move the Joystick (/) left or right, fi nd the fi rst position you wish
to play back.
6. Press the Joystick.
•
The images you recorded will appear on the TV after a few
seconds.
•
If a tape reaches its end while being played back, the tape will
rewind automatically.
7. To stop the playback, move down the Joystick (
•
The playback mode (SP/LP) is selected automatically.
•
If only a mono audio input is available on the TV set, use the
audio cable with the white jack (Audio L).
69_ English
VCR
TV
Signal flow
Antenna
).
.
▼)
連接到沒有聲訊 / 視訊輸入插孔的電視機
•
您可以透過 VCR 將您的攝錄放影機連接到電視機。
1. 使用聲訊 / 視訊線將攝錄放影機連接到您的 VCR。
•
黃色插孔:視訊
•
白色插孔:Audio(L)(聲訊(左) )- 單聲道
•
紅色插孔:Audio(R)(聲訊(右) )
Camcorder
AV
DV
AV Jack
MODE
POWER
CHG
Audio/Video
Cable
播放錄影帶
1. 連接電源
2. 放入您要播放的錄影帶。
3. 將選擇開關設定為 TAPE。 (僅適用於 SC-D383/D385)
4. 按下 MODE 按鈕以設定 Player (
5. 向左或向右移動 Joystick (/) 尋找您要播放的首個位置。
6. 按下 Joystick。
•
您所錄製的影像會在數秒後出現在電視機上。
•
若錄影帶在播放時播到帶子結束、錄影帶將自動回轉。
7. 若要停止播放、可向下移動 Joystick (
•
將會自動選擇播放模式 (SP/LP)。
•
若電視機上只有一個單聲道聲訊輸入可以使用、請將聲訊纜
線用於白色插孔(Audio L(聲訊左) ) 。
2. 將電視機連接到 VCR。
2.
3. 將選擇開關設定為 TAPE。
3.
(僅適用於 SC-D383/D385)
4. 按下 MODE 按鈕以設定 Player
4.
(
).
5. 打開電視機和 VCR。
5.
•
將 VCR 上的輸入選擇器設定為
「線」 。
•
在電視機上選擇為您的 VCR
所保留的頻道。
6. 播放錄影帶。
6.
).
▼ )
.
臺灣 _69