Electrical Safety; General Power Tool Safety Warnings - Ozito ECS-2040U Original Instruction

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of fire, electric shock, personal
injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The manufacturer cannot accept any liability for damage or accidents which arise due to a failure to
follow these instructions and the safety information.
Before you connect the equipment to the mains supply make sure that the data on the rating plate
are identical to the mains data.
This tool is double insulated therefore no earth wire is required.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING!
"Read all safety warnings, instructions, illustrations and specifications provided
with this power tool." Failure to follow the warnings and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
b.
gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
2. Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
a.
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on invites accidents.
SPECIAL SAFETY INSTRUCTIONS FOR CHAINSAWS
• When the chainsaw is running make sure that you keep all parts of your body away from the chainsaw.
Before starting up the chainsaw make sure that it is not touching anything. When you are working with a
chainsaw, a single moment of carelessness is all it takes for clothing or parts of your body to get caught by the
chainsaw.
• Always hold the chainsaw securely with your right hand on the rear handle and your left hand on
the front handle. Holding the chainsaw with your hands in other positions increases the risk of injury and is
therefore not allowed
• Hold the appliance only by the insulated handles when carrying out work during which the cutting tool
could strike concealed power cables or its own cable. Contact with a live cable will also make the metal
parts of the appliance live and will cause an electric shock.
• Wear safety goggles and ear protection. Other safety equipment for the head, hands, legs and feet is
recommended. Correct protective clothing reduces the risk of injury caused by catapulted chips or in the event
of accidental contact with the chainsaw.
• Never use the chainsaw up a tree. You risk injuring yourself if you use the chainsaw up a tree.
• Always maintain a steady standing position and only use the chainsaw when you are standing on a
solid, safe and flat surface. Slippery or unsafe surfaces in combination with a ladder can cause you to lose
your balance and control over the chainsaw.
• When cutting through a branch which is under tension, take into account how it will spring back once
the cut has been made. Once the tension in the wood fibres is released, the tensioned branch could hit the
operator and/or seize control of the chainsaw.
• Take special care when cutting undergrowth and young trees. The thin material can become caught in the
saw chain and whip back towards you or make you lose your balance.
• Carry the chainsaw by the front handle with the chainsaw switched off and the chain facing away from
the body. Always fit the protective cover when transporting the chainsaw or putting it into storage.
Careful handling of the chainsaw reduces the likelihood of accidental contact with the saw chain while it is
running.
• Follow the instructions for lubrication, chain tension and replacement of accessories. A chain which is
not properly tensioned or lubricated can either break or increase the risk of kickback.
• Keep the handles dry, clean and free from oil and grease. Greasy or oily handles are slippery and will result
in loss of control.
• Only use the chainsaw to cut wood. The chain must only be used to perform the work for which it is
intended. For example: Never use the chainsaw to cut plastic or brickwork or building materials which
are not made of wood. Use of the chainsaw for non-intended or non-approved work can create dangerous
situations.
Causes of ways to avoid recoil
Recoil can occur if the tip of the chain bar touches an item or if the wood bends and jams the saw chain in the
cut.
In many cases contact with the bar tip can result in an unexpected reaction aimed backwards in which the chain
bar is catapulted upwards towards the operator. Jamming the saw chain on the top of the chain bar can catapult
the bar towards the operator at high speed.
The power supply for this product should be protected by a residual current device (rated at 30mA
or less). A residual current device reduces the risk of electric shock.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order
to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible electrical
insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect
the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged
or defective. When using an extension lead on a reel, always unwind the lead completely. Use of
an extension lead not suitable for the power input of the tool or which is damaged or defective may
result in a risk of fire and electric shock.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these
g.
are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
d.
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
f.
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Any of these reactions can result in you losing control over the saw and possibly suffering serious injuries. You
should therefore not rely totally on the safety equipment fitted to the chainsaw. When using a chainsaw you
should take various precautions to enable you to work without suffering accidents or injuries.
Recoil is the result of incorrect or wrong use of the electric tool. It can be prevented by suitable precautions, as
described below:
• Hold the saw firmly with both hands, with fingers and thumbs gripped around the handles. Steady
yourself with your body and arms in a position in which you can control the kickback forces. Provided
appropriate measures are taken, an operator should be capable of controlling the kickback forces. Never let go
of the chain saw.
• Avoid abnormal working postures. Never cut above shoulder height. This prevents accidental contact with
the tip of the rail and offers better control over the chainsaw in unexpected situations.
• Always use the correct replacement rails and saw chains recommended by the manufacturer. The use of
incorrect replacement rails or saw chains may result in breakage of the chain and/or kickback.
• Follow the manufacturer's instructions for sharpening and maintaining the saw chain. The risk of
kickback is increased if the depth limiter is set too low.
More important information:
• Use an earth-leakage circuit breaker with a trip current of 30 mA or less.
• Position the power cable such that it cannot be caught by branches or the like during sawing.
• We recommend that first-time users should at least practice cutting roundwood (logs) on a sawing trestle or
similar.
Residual risks
Even if you use this electric power tool in accordance to instructions, certain residual risks cannot be
eliminated. The following hazards may arise in connection with the equipment's construction and layout:
• Cut injuries if no safety clothing is used.
• Lung damage if no suitable protective dust mask is applied.
• Damage to hearing if no suitable ear protection is applied.
• Health damage caused by hand-arm vibrations if the equipment is used over a longer period or is not properly
guided and maintained.
Warning! The electric power tool generates an electromagnetic field during operation. Under certain
circumstances this field may actively or passively impede medical implants. To reduce the risk of serious or
fatal injuries, we recommend persons with medical implants to consult their doctor and the manufacturer of the
medical implant prior to using the equipment.
Do not lose this safety information.