Table of Contents
Advertisement
FastMig
MR 200, MR 300
Operating manual
Bruksanvisning
Gebrauchsanweisung
Manual de instrucciones
Käyttöohje
Manuel d'utilisation
Manuale d'uso
Gebruiksaanwijzing
Brugsanvisning
Instrukcja obsługi
Manual de utilização
Инструкции по эксплуатации
Bruksanvisning
操作手册
EN
DA
DE
ES
FI
FR
IT
NL
NO
PL
PT
RU
SV
ZH
Advertisement
Table of Contents
Related Manuals for Kemppi FastMig MR 200
Summary of Contents for Kemppi FastMig MR 200
- Page 1 FastMig MR 200, MR 300 Operating manual Bruksanvisning Gebrauchsanweisung Manual de instrucciones Käyttöohje Manuel d’utilisation Manuale d’uso Gebruiksaanwijzing Brugsanvisning Instrukcja obsługi Manual de utilização Инструкции по эксплуатации Bruksanvisning 操作手册...
- Page 3 OPERATING MANUAL English...
-
Page 4: Table Of Contents
..................FastMig MR 200, MR 300... -
Page 5: Preface
This operating manual contains important information on the use, maintenance and safety of your Kemppi product. The technical specifications of the equipment can be found at the end of the manual. -
Page 6: Use
FastMig MR 200 and MR 300 panels are supposed to be used only with synergic power sources FastMig M 320, 420 or 520. MR 200 panel can be mounted to MXF 63 (200 mm wire spool) wire feeder and MR 300 panel to MXF 65 and 67 (300 mm wire spool) wire feeders. -
Page 7: Functions Of Mr 200 And Mr 300 Panel
Adjustment of SETUP parameters 11. Manual control/remote control unit selection With MR 200 and MR 300 panels 'Wire Inch' and 'Gas Test' buttons should be used from the NOTE! inside of the wire feed unit. © Kemppi Oy / 1515... -
Page 8: Mr 200 And Mr 300 Operations
MIG gun has been connected to the equipment. When liquid cooling is selected, the liquid cooling unit will start up in connection with the next equipment start-up. The selection can also be made through the SETUP function. FastMig MR 200, MR 300... - Page 9 Remote control unit is connected to the device by pressing button 11. The wire feed speed and welding voltage setting operations are performed via remote control. In this case, potentiometers 9 and 10 (control knobs) of the panel are disconnected. © Kemppi Oy / 1515...
-
Page 10: Panel Mr 200 And Mr 300 Setup Parameters
The remaining time for the WiseDemo licence **’’ , OFF (readable value only). 3-h = max. 3 hours left 2-h = max. 2 hours left **’ = ** minutes left **’’ = ** seconds left OFF = Demo period has expired. FastMig MR 200, MR 300... - Page 11 Control panel reset function. OFF = No reset Restore Factory PAn = Settings will be restored, but OFF, PAn, ALL Settings memory channels remain unchanged ALL = All settings will be restored to factory values © Kemppi Oy / 1515...
-
Page 12: Fastmig Error Codes
Gas is unconnected to the wire feeder. Gas has been ran out, gas hose is leaking or there is no pressure enough in the gas web. Connect the gas to the wire feeder, check gas hose and the pressure of the gas web. FastMig MR 200, MR 300... -
Page 13: Disposal
The owner of the equipment is obliged to deliver a decommissioned unit to a regional collection centre, per the instructions of local authorities or a Kemppi representative. By applying this European Directive you will improve the environment and human health. - Page 14 Tel. +61 2 9605 9500 sales.india@kemppi.com DK-2740 SKOVLUNDE Telefax +61 2 9605 5999 DANMARK info.au@kemppi.com KEMPPI WELDING SOLUTIONS SDN BHD Tel +45 4494 1677 No 12A, Jalan TP5A, OOO KEMPPI Telefax +45 4494 1536 Taman Perindustrian UEP, Polkovaya str. 1, Building 6 sales.dk@kemppi.com...