Installation - BOMANN EBKI 961 Instruction Manual

Hide thumbs Also See for EBKI 961:

Instruction manual (32 pages)

Table Of Contents

Table of Contents

Enlarged version

Installation

WARNING:

The installation and the connection to the main power

and the connection to the main power

may only be performed by an authorized specialist.

CAUTION: : : :

CAUTION

• The worktop, the cabinet, veneers

, the cabinet, veneers, plastic coat-

ings, used adhesives etc. must be sufficient

adhesives etc. must be sufficient heat-

resistant.

• The appliance must be installed so that heat can

must be installed so that heat can

be dissipated. The ventilation openings (D) and

sipated. The ventilation openings (D) and

(E) must not be blocked.

• The distance between the hob and an extractor

hood must be at least as large as specified in the

instructions of the extractor hood!

• Below the cutout must remain a minimum di

Below the cutout must remain a minimum dis-

tance. In this area are not allowed heat

tance. In this area are not allowed heat-sensitive

objects (cabinet, drawer, etc.). Possibly existing

sidewalls or drawer boxes must be sawed accor

walls or drawer boxes must be sawed accord-

ingly or removed.

• Keep safety distances; sufficient air circulation

Keep safety distances; sufficient air circulation

must be ensured:

Preparing the worktop for installation of the hob

CAUTION:

Before cutting secure the outer cutout edge with wide

adhesive tape to avoid traces of jigsaw on the wor

adhesive tape to avoid traces of jigsaw on the work-

top.

• The worktop must have a thickness between

The worktop must have a thickness between

28 mm and 40 mm, it must be leveled horizontally

and are sealed to the wall side against overflow-

and are sealed to the wall side against

ing liquids or moisture.

hob and an extractor

A A A A

760 mm

B B B B

50 mm

C C C C

20 mm

D D D D

Air intake

E E E E

Air outlet (5 mm)

• The hob must be completely surrounded by min.

50 mm work surface.

• The cut surfaces (cutout edges) must be sealed

The cut surfaces (cutout edges) must be sealed

with special varnish, silicone rubber or cast raisin

in order to prevent swelling caused by humidity.

Clean and dry the worktop in the cutout area

and dry the worktop in the cutout area

•

thoroughly.

Worktop cutout

Prepare the cutout of the worktop according to the

dimensional drawing.

Dimensions in mm

L L L L

W W W W

H H H H

590

520

S S S S Seal below the hob

Installing the hob

• First check the factory fitted hob seal at the hob

First check the factory fitted hob seal at the hob

frame to the integrity and the proper fit.

• Affix the brackets (1) to the

Affix the brackets (1) to the provided drillings (2)

of the hob with the screws (3).

with the screws (3).

• Put the hob with the connecting cable first and

Put the hob with the connecting cable first and

with the control panel to the front into the pr

with the control panel to the front into the pre-

pared cutout.

• Make sure that the distances to the cutting are

Make sure that the distances to the cutting are

equal on all four sides and that the seal is resting

on the worktop.

completely surrounded by min.

D D D D

A A A A

B B B B

560

490

1 1 1 1

Bracket

2 2 2 2

Drilling

3 3 3 3

Screw

A A A A

Worktop

B B B B

Hob bottom

1 1 1 1

Bracket

3 3 3 3

Screw

X X X X

Table of Contents

Installation - BOMANN EBKI 961 Instruction Manual

Installation

Related Manuals for BOMANN EBKI 961

Related Content for BOMANN EBKI 961

Table of Contents