Table of Contents
Advertisement
Do not use harsh abrasive cleaners or sharp metal objects for cleaning the glass
Do not use harsh abrasive cleaners or sharp metal objects for cleaning the glass
Do not use harsh abrasive cleaners or sharp metal objects for cleaning the glass
•
surface. The glass can be scratched or destroved.
The glass can be scratched or destroved.
• Do not try to repair the appliance on your own. Always contact an authorized
Do not try to repair the appliance on your own. Always contact an authorized
Do not try to repair the appliance on your own. Always contact an authorized
technician. If the supply cord is damaged, it must be replaced by the manufactu
technician. If the supply cord is dam
er, its service agent or similarly qualified persons in order to avoid a hazard.
er, its service agent or similarly qualified persons in order to avoid a hazard.
er, its service agent or similarly qualified persons in order to avoid a hazard.
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
Unpacking the Appliance
• Remove the appliance from its packaging.
Remove the appliance from its packaging.
• Remove all packaging material, such as foils, filler
Remove all packaging material, such as foils, filler
and cardboard packaging.
• To prevent hazards, check the appliance for any
To prevent hazards, check the appliance for any
transport damage.
• In case of damage, do not put the appliance into
In case of damage, do not put the appliance into
operation. Contact your distributor.
operation. Contact your distributor.
NOTE: : : :
NOTE
NOTE
NOTE
Production residue or dust may have collected on the
Production residue or dust may have collected on the
appliance. We recommend cleaning the appliance
according to chapter "Cleaning".
Appliance Equipment
Appliance Equipment
Appliance Equipment
Appliance Equipment
Appliance Equipment
Appliance Equipment
Appliance Equipment
Appliance Equipment
Hob arrangement
Hob arrangement
Hob arrangement
Hob arrangement
NOTE
NOTE: : : :
NOTE
NOTE
The listed power settings can vary depending on the
power settings can vary depending on the
material and/or size of the cookware.
material and/or size of the cookware.
Delivery scope
De
De
De
livery scope
livery scope
livery scope
installation material:
4 x mounting bracket, 4 x fixing
screw
ning the appliance
1 1 1 1 Control panel
Control panel
2 2 2 2 Ø180 mm / 2000 W
180 mm / 2000 W
3 3 3 3 Ø160 mm / 1500 W
160 mm / 1500 W
4 4 4 4 Ø180 mm / 2000 W
180 mm / 2000 W
5 5 5 5 Ø160 mm / 1500 W
160 mm / 1500 W
bracket, 4 x fixing
aged, it must be replaced by the manufactur-
WARNING:
WARNING:
WARNING:
WARNING:
The installation and the connection to the main power
may only be performed by an authorized specialist.
may only be performed by an authorized specialist.
CAUTION
CAUTION
CAUTION
CAUTION: : : :
• The worktop, the cabinet, veneers
ings, used adhesives etc. must be sufficient
adhesives etc. must be sufficient heat-
resistant.
• The appliance must be installed so that heat can
be dissipated. Air inlet (D) and air outlet (E) must
not be blocked.
• The appliance conforms to the heat insulation
The appliance conforms to the heat insulation
class Y, i.e. only one side of the appliance may be
class Y, i.e. only one side of the appliance may be
installed near higher kitchen furniture or walls.
installed near higher kitchen furniture or walls.
• The distance between the hob and an extractor
The distance between the hob and an extractor
hood must be at least as large as specified in the
hood must be at least as large as specified in the
instructions of the extractor hood!
instructions of the extractor hood!
• Below the cutout must remain a minimum di
tance (B). In this area are not allowed heat-
tance (B). In this area are not allowed heat
sensitive objects (cabinet, drawer, etc.). Possibly
sensitive objects (cabinet, drawer, etc.). Possibly
existing sidewalls or drawer boxes must be sawed
existing sidewalls or drawer boxes must be sawed
accordingly or removed.
• Keep safety distances; sufficient air circulation
must be ensured:
5
Installation
Installation
Installation
Installation
Installation
Installation
Installation
Installation
and the connection to the main power
cabinet, veneers, plastic coat-
must be installed so that heat can
Air inlet (D) and air outlet (E) must
t remain a minimum dis-
; sufficient air circulation
A A A A
600 – 750 mm
B B B B
50 mm
C C C C
20 mm
D D D D
Air inlet
E E E E
Air outlet
Advertisement
Table of Contents
