Page 1
Smart EVB G2 User Guide Smart LTE Module Series Rev. Smart_EVB_G2_User_Guide_V1.1 Date: 2018-06-05 Status: Released www.quectel.com...
Page 2
QUECTEL OFFERS THE INFORMATION AS A SERVICE TO ITS CUSTOMERS. THE INFORMATION PROVIDED IS BASED UPON CUSTOMERS’ REQUIREMENTS. QUECTEL MAKES EVERY EFFORT TO ENSURE THE QUALITY OF THE INFORMATION IT MAKES AVAILABLE. QUECTEL DOES NOT MAKE ANY WARRANTY AS TO THE INFORMATION CONTAINED HEREIN, AND DOES NOT ACCEPT ANY LIABILITY FOR ANY INJURY, LOSS OR DAMAGE OF ANY KIND INCURRED BY USE OF OR RELIANCE UPON THE INFORMATION.
Smart LTE Module Series Smart EVB G2 User Guide About the Document History Revision Date Author Description 2017-09-19 Vae LIU Initial Updated the description of (U)SIM Interfaces in Table 1. Updated the description of camera interface. Added the reserved MIPI+SPI/I2S Interface.
Key Features ..........................10 2.2. Interface Overviews ........................12 2.3. Top and Bottom Views of Smart EVB G2 ................. 15 2.4. Smart EVB G2 Kit Accessories ....................16 Smart EVB G2 Kit Accessories Assembly ..................19 Interface Applications ........................20 4.1.
Page 5
Smart LTE Module Series Smart EVB G2 User Guide Operation Procedures Illustration ....................52 5.1. Power ON Smart Modules ......................52 5.2. Communication Via USB or UART Interface ................53 5.2.1. Communication via USB Interface ................. 53 5.2.2. Communication via UART Interface ................54 5.3.
Page 6
Smart EVB G2 User Guide Table Index TABLE 1: KEY FEATURES ..........................10 TABLE 2: INTERFACES OF SMART EVB G2 ....................13 TABLE 3: ACCESSORIES LIST ........................17 TABLE 4: PIN DEFINITION OF BATTERY INTERFACE .................. 22 TABLE 5: DESCRIPTION OF POWER SUPPLY SWITCHES ................24 TABLE 6: PIN DEFINITION OF B2B CONNECTORS..................
Page 7
FIGURE 5: SMART EVB G2 KIT ACCESSORIES .................... 17 FIGURE 6: SMART EVB G2 KIT ACCESSORIES ASSEMBLY ................ 19 FIGURE 7: SIMPLIFIED POWER SUPPLY BLOCK DIAGRAM OF SMART EVB G2 ........21 FIGURE 8: 5V DC POWER JACK ........................21 FIGURE 9: POWER PLUG DESIGN .........................
Smart LTE Module Series Smart EVB G2 User Guide Introduction This document describes the evaluation board (Smart EVB G2) for Quectel Smart module SC60. The smart evaluation board is an assistant tool to develop and test Quectel SC60 modules. Smart_EVB_G2_User_Guide...
SC60 module. Manufacturers of the cellular terminal should send the following safety information to users and operating personnel, and incorporate these guidelines into all manuals supplied with the product. If not so, Quectel assumes no liability for customers’ failure to comply with these precautions.
Smart LTE Module Series Smart EVB G2 User Guide General Overview Quectel supplies Smart EVB G2 for designers to develop applications based on Quectel SC60 module. This EVB can test basic functionalities of the module. 2.1. Key Features The following table describes the detailed features of Smart EVB G2.
Page 12
Smart LTE Module Series Smart EVB G2 User Guide One mono loudspeaker differential amplifier output Support USIM/SIM cards: 1.8V and 2.95V (U)SIM Interfaces Support dual SIM dual standby Two UART interfaces: UART Interfaces Main UART for data transmission and AT command communication ...
Smart LTE Module Series Smart EVB G2 User Guide SPEAKER EARPHONE BATTERY PACK Figure 2: Smart EVB G2 Interface Overview (Bottom) Table 2: Interfaces of Smart EVB G2 Interface Reference Number Description J0201 The power jack on the EVB. Typical power supply: +5.0V...
Page 15
D0502 indicates the charge status of the module D0503* D0503* indicates the operation status of the module TE-A J0101, J0102 Connectors for connecting Smart TE-A and Smart EVB G2 J0401 Rear camera connector, support 16M CMOS sensor Cameras J0402 Front camera connector, support 8M CMOS sensor Flashlight LED1 for testing module’s flashlight interfaces...
Ambient light sensor and proximity sensor Coin Cell BAT0201 Coin cell battery for RTC power supply MIPI+SPI/I2S J0902 Reserved NOTE “*” means under development. 2.3. Top and Bottom Views of Smart EVB G2 Figure 3: Smart EVB G2 Top View Smart_EVB_G2_User_Guide 15 / 59...
Smart EVB G2 User Guide Figure 4: Smart EVB G2 Bottom View 2.4. Smart EVB G2 Kit Accessories All accessories of the Smart EVB G2 kit are listed as below. Please contact the supplier if there is something missing. Smart_EVB_G2_User_Guide 16 / 59...
USB Type-C cable Bolts and coupling nuts Wi-Fi/BT antenna RF cables Main antennas GNSS antenna 5V DC adapter Figure 5: Smart EVB G2 Kit Accessories Table 3: Accessories List Items Description Quantity USB to RS232 converter cable Cables USB Type-C cable...
Page 19
Including USB 2.0 to RS232 driver, USB driver, etc. Battery Li-polymer battery Adapter 5.0V DC power supply Others Bolts and coupling nuts for fixing Smart EVB G2 4 for each NOTE The main antenna can also be used for diversity reception. Smart_EVB_G2_User_Guide 18 / 59...
4.1. Power Supply Interfaces (J0201/J0202) The Smart EVB G2 can be powered by an external 5.0V DC power adapter. Connect the DC power adapter to the power jack (J0201) and then the step-down converter (DC-to-DC converter), which is used to regulate the 5.0V DC power supply voltage to 4.2V for powering up the module.
Figure 8: 5V DC Power Jack Before connecting the power supply, customers have to select a proper +5V DC power adapter to supply power for the Smart EVB G2, and the power plug design of the adapter is shown as below. Inner contact...
Smart LTE Module Series Smart EVB G2 User Guide 4.1.2. Battery Interface The following figure shows a reference circuit design for battery interface. Figure 10: Reference Design for Battery Interface The following figure shows the pin assignment of battery interface, and the following table shows the pin definition of battery connector.
Smart LTE Module Series Smart EVB G2 User Guide Power input pins. 5, 6 VBAT Connect to the positive pole of the battery. Figure 12: Battery Assembly 4.1.3. Switches for Power Supply The switches for power supply are shown in following figure. S0201 is used to switch between DC power supply and battery power supply.
Smart LTE Module Series Smart EVB G2 User Guide Table 5: Description of Power Supply Switches Switch No. Description S0201 Used to select DC power supply or battery power supply S0202 Used to switch on/off the power supply 4.2. Smart TE-A Interface The Smart TE-A interface supports SC60 module, and includes two B2B connectors named J0101 and J0102, respectively.
Smart LTE Module Series Smart EVB G2 User Guide Figure 15: Sketch Map of Smart TE-A (Top View) The following table describes the pin definition of the two B2B connectors J0101 and J0102. Table 6: Pin Definition of B2B Connectors Pin No.
LCM Interfaces 4.3.1. Main LCM Interface The Smart EVB G2 provides two LCM interfaces and can be equipped with two LCD modules for dual display function. Currently the Smart EVB G2 provides two 5-inch 1280 × 720 HD resolution liquid crystal displays for customers to test.
Smart LTE Module Series Smart EVB G2 User Guide 4.3.2. Secondary LCM Interface The following figure shows a reference circuit design for secondary LCM interface of the Smart EVB G2. LDO17_2V 85 LDO6_1V8 J0801 LCM1_LED+ LEDA LCM1_LED- LEDK LPTE LCD1_TE...
Figure 18: Pin Assignments of LCM Interfaces 4.3.3. Backlight Driver for Secondary LCM Interface The Smart EVB G2 uses a PWM dimming step-up LED driver for the WLED backlighting of secondary LCM interface. The following figure shows a reference circuit design for the backlight driver.
Smart LTE Module Series Smart EVB G2 User Guide 4.4. Touch Panel Interfaces The Smart EVB G2 provides two touch panel interfaces: J0804 and J0802. J0804 is used for the connection between touch panel interfaces of main LCM and EVB. ...
2.8V power supply for touch panel VDD power 4.5. Camera Interfaces Smart EVB G2 provides two camera interfaces (4-lane+2-lane) with rear camera and front camera assembled. The rear camera uses a 16M pixels digital CMOS sensor with auto-focusing function.
Figure 23: Camera Interfaces with Cameras Assembled 4.6. USB Interfaces The Smart EVB G2 provides two USB interfaces: Micro USB interface and Type-C interface. The Type-C interface complies with the USB 3.0/2.0 specifications and supports super speed (5Gbps) on USB 3.0, high speed (480 Mbps) on USB 2.0 and full speed (12 Mbps) modes.
Smart EVB G2 provides three analog audio outputs including one mono loudspeaker, one mono earphone, and one stereo headset. The Smart EVB G2 also provides three analog audio inputs including two single-ended and one differential microphone inputs. One single-ended microphone input is used for headset interface.
Figure 29: Sketch of Audio Plug 4.7.3. Earphone Interface Smart EVB G2 provides one earphone interface and the earphone is soldered onto the Smart EVB G2 via test point J1204. The following figure shows a reference circuit design for earphone interface.
Smart EVB G2 User Guide 4.7.4. Microphone Interfaces Smart EVB G2 provides one single-ended and one differential microphone inputs for microphone interfaces. The single-ended microphone input is for MEMS-Type microphone and the differential microphone input is for ECM-Type microphone. The following figures show a reference circuit design for microphone interfaces and the two microphones.
Smart EVB G2 User Guide 4.8. (U)SIM Interfaces The Smart EVB G2 provides two 6-pin push-push type (U)SIM card (3V or 1.8V) connectors J1001 ( (U)SIM1 card connector) and J1002 ((U)SIM2 card connector). The following figure shows the simplified interface schematic for J1001.
4.9. UART Interfaces Smart EVB G2 provides two UART interfaces: main UART port J1301 and debug UART port J1302. The main UART interface can be used for data transmission and AT command communication. And the debug UART interface is used for debugging.
The schematic and pin assignment of J1302 are the same as J1301’s. 4.10. SD Card Interface Smart EVB G2 provides an SD card interface J1101 for customers to test the module’s SD card interface. The following figure shows the simplified interface schematic for SD card interface on Smart EVB G2. SD_LDO11...
4.11. Flashlights Smart EVB G2 provides two flashlight LEDs D0301 and D0302 for testing the module’s flashlight interfaces which support flash mode and torch mode. The following figures show a reference circuit design for flashlights and their locations on Smart EVB G2.
4.13. Emergency Download Interface Smart EVB G2 provides one emergency download switch USB_BOOT to force the module enter into download mode. Pull up USB_BOOT pin to 1.8V before powering on the module when the function is used. The following figures show a reference circuit design for the emergency download interface and its switch.
Smart EVB G2 User Guide 4.14. Vibrator Smart EVB G2 provides an ERM-type vibrator for customers to test the motor driver interface of Smart modules. The following figures show a reference circuit design and the vibrator on the board. 33pF...
Smart LTE Module Series Smart EVB G2 User Guide Figure 46: Buttons Table 11: Description of Buttons Reference No. Items Description Power key (push button) S0502 PWRKEY Used to turn on/off the module S0503 RESET Reserved S0505 VOL_UP Used to turn the volume up...
Smart LTE Module Series Smart EVB G2 User Guide POWER STATUS CHARGE Figure 47: Status Indication LEDs Table 12: Description of Status Indication LEDs Reference No. Items Description Indicate the power supply status of Smart modules D0501 POWER Bright: VBAT ON...
Smart LTE Module Series Smart EVB G2 User Guide Operation Procedures Illustration This chapter introduces how to use the Smart EVB G2 for testing and evaluating Quectel Smart modules. 5.1. Power ON Smart Modules The following are the procedures for powering on the smart modules.
Power on the module according to the procedures mentioned in Chapter 5.1. Connect Smart EVB G2 and the PC with USB cable through USB interface and then run the USB flash drive on PC to install the USB driver and ADB driver. The USB port numbers can be viewed through the PC’s Device Manager, shown as below.
Smart LTE Module Series Smart EVB G2 User Guide Figure 50: “adb shell” Command NOTES 1. If customers want to use HyperTerminal for testing, then Qualcomm HS-USB Modem 9091 can be used. 2. Please note that the USB port numbers may be different among different modules.
Smart LTE Module Series Smart EVB G2 User Guide Install and then use the QCOM tool provided by Quectel to realize the communication between the smart module and the PC. The following figure shows the QCOM configuration: select correct “COM port”...
Smart LTE Module Series Smart EVB G2 User Guide Figure 53: Firmware Upgrade Steps 5.4. Power OFF Smart Modules There are two methods to power off the module. The steps for the first method are as follows: 1. Press D0501 (PWRKEY) for at least 1s under the power-on state of the module, and then LCD will...
Page 58
Smart LTE Module Series Smart EVB G2 User Guide Figure 54: LCD Menu Display for Powering off Module 2. Choose “Power off” option. 3. The module will be powered off normally. The other method is to press down PWRKEY for at least 8s until the module is shut down completely.
Smart LTE Module Series Smart EVB G2 User Guide Appendix A References Table 13: Related Documents Document name Remark Quectel_SC60_R1.0&R2.0_Hardware_Design SC60 R1.0&R2.0 hardware design Quectel_SC60_R1.0&R2.0_Reference_Design SC60 R1.0&R2.0 reference design Quectel_SC60_R1.1&R2.1_Hardware_Design SC60 R1.1&R2.1 hardware design Quectel_SC60_R1.1&R2.1_Reference_Design SC60 R1.1&R2.1 reference design Quectel_QCOM_User_Guide...
Page 60
Smart LTE Module Series Smart EVB G2 User Guide Pulse Width Modulation UART Universal Asynchronous Receiver & Transmitter Universal Serial Bus (U)SIM (Universal) Subscriber Identity Module WLED White LED Zero Insert Force Smart_EVB_G2_User_Guide 59 / 59...
Need help?
Do you have a question about the Smart EVB G2 and is the answer not in the manual?
Questions and answers