2. INSTALLATION ............................EN-11 2.1 Unpackng ..............................EN-11 2.2 External Connectons ..........................EN-11 2.2.1 Scale Base wth Connector to T51P ....................EN-11 2.2.2 RS232 Interface Cable to T51P......................EN-11 2.2.3 AC Power to T51P ........................EN-11 2.2.4 AC Power to T51XW ........................EN-11 2.2.5 Battery Power to T51P ........................EN-11 2.2.6 Mountng Bracket ...........................EN-12 2.3 Internal Connectons ..........................EN-12 2.3.1 Openng the Housng ........................EN-12 2.3.2 Scale Base Wthout Connector to T51P or T51XW ................EN-12 2.3.3 RS232 Interface Cable to T51XW ......................EN-13 2.3.4 Footswtch to T51P or T51XW ......................EN-13 2.4 T51P Rear Housng Orentaton .........................EN-13 2.5 Mountng Bracket .
Page 4
EN- 5000 Series Indicators TABLE OF CONTENTS (Cont.) 3.4.11 Beeper Sgnal ..........................EN-23 3.4.12 Button Beeper ..........................EN-23 3.4.13 End Setup ............................EN-23 3.5 Readout Menu ............................EN-23 3.5.1 Reset ............................EN-24 3.5.2 Stable Range ..........................EN-24 3.5.3 Flter ............................EN-24 3.5.4 Auto-Zero Trackng ........................EN-24 3.5.5 Backlght .............................EN-25 3.5.6 Auto Off Tmer ..........................EN-25 3.5.7 Gross Indcator ..........................EN-25 3.5.8 End Readout ..........................EN-25 3.6 Mode Menu .
Page 5
5000 Series Indicators EN- TABLE OF CONTENTS (Cont.) 3.9.5 Layout Sub-menu .........................EN-35 3.9.6 Output ............................EN-35 3.9.7 Lst Menu Settngs .........................EN-35 3.9.8 End Prnt1 or End Prnt2 ........................EN-35 3.10 COM1 and COM2 Menus .........................EN-35 3.10.1 Reset ............................EN-36 3.10.2 Baud ............................EN-36 3.10.3 Party ............................EN-36 3.10.4 Stop Bt ............................EN-36 3.10.5 Handshake ..........................EN-36 3.10.6 Address ............................EN-36 3.10.7 Alternate Command Sub-menu .......................EN-37 3.10.8 End COM1 or End COM2 .......................EN-37 3.11 I-O Menu .
Page 6
5.2 Output Format ............................EN-49 5.3 Prntouts ..............................EN-49 6. LEGAL FOR TRADE ...........................EN-51 6.1 Settngs ..............................EN-51 6.2 Verfcaton ..............................EN-51 6.3 Sealng ..............................EN-51 7. MAINTENANCE ............................EN-53 7.1 Model T51P Cleanng ..........................EN-53 7.2 Model T51XW Cleanng ..........................EN-53 7.3 Troubleshootng ............................EN-53 7.4 Servce Informaton ..........................EN-54 8. TECHNICAL DATA .............................EN-55 8.1 Specfcatons ............................EN-55 8.2 Accessores and Optons ...........................EN-56 8.3 Drawngs and Dmensons ........................EN-57...
5000 Series Indicators EN-5 INTRODUCTION Ths manual contans nstallaton, operaton and mantenance nstructons for the T51P and T51XW Indcators. Please read ths manual completely before nstallaton and operaton. Safety Precautions For safe and dependable operaton of ths equpment, please comply wth the followng safety precautons: • Verfy that the nput voltage range prnted on the data label matches the local AC power to be used. • Make sure that the power cord does not pose a potental obstacle or trppng hazard. • Use only approved accessores and perpherals. • Operate the equpment only under ambent condtons specfed n these nstructons. • Dsconnect the equpment from the power supply when cleanng. • Do not operate the equpment n hazardous or unstable envronments. • Do not mmerse the equpment n water or other lquds. • Servce should only be performed by authorzed personnel. • The T51XW s suppled wth a grounded power cable. Use only wth a compatble grounded power outlet 1.1.1 Relay Option Safety Precautions Ths equpment may have an optonal AC or DC Relay Opton board nstalled. Ths opton allows external devces to be controlled by the Indcator. CAUTION: ELECTRICAL SHOCK HAZARD. REMOVE ALL POWER CONNECTIONS TO THE INDICATOR BEFORE SERVICING OR MAKING INTERNAL CONNECTIONS. THE HOUSING SHOULD ONLY BE OPENED BY AUTHORIZED AND QUALIFIED PERSONNEL, SUCH AS AN ELECTRICAL TECHNICIAN.
EN- 5000 Series Indicators Overview of Parts and Controls TABLE 1-1. T51P PARTS. Item Description Data Label Front Housng Control Panel Adjustng Knob (2) Mountng Bracket Securty Screw Data Label Rear Housng Battery Cover Screw (4) Power Receptacle Hole plug for opton Stran relef for alternate load cell connecton Load Cell Connector Hole plug for opton RS232 Connector Fgure 1-1. T51P Indcator.
Page 9
5000 Series Indicators EN- Overview of Parts and Controls (Cont.) TABLE 1-. T51XW PARTS. Item Description Data Label Front Housng Control Panel Adjustng Knob (2) Mountng Bracket Screw (4) Rear housng Data Label Securty Screw Stran relef for opton Stran relef for RS232 Stran relef for opton Stran relef for opton Stran relef for Load Cell Cable Power cord 13 14 Fgure 1-2. T51XW Indcator.
Page 10
EN- 5000 Series Indicators Overview of Parts and Controls (Cont.) Fgure 1-3. Man PC Board. TABLE 1-. MAIN PC BOARD. Item Description Sense Jumper W1 Alternate Load Cell Termnal Block J4 Sense Jumper W2 Securty Swtch SW2 External nput Termnal Block J9 RS232 Termnal Block J7 (T51XW only) Load Cell Connector (T51P only)
Page 11
5000 Series Indicators EN- Overview of Parts and Controls (Cont.) 7 8 9 Fgure 1-4. Controls and Indcators. TABLE 1-. CONTROL PANEL. Designation Designation TARE Menu button UNDER LED Peces symbol ACCEPT LED FUNCTION Mode button OVER LED PRINT Unts button Capacty Label Wndow ON/ZERO Off button Brackets (not used) Ponter symbols (not used) Klogram, gram symbols Brutto, Gross symbols Scale symbol (not used)
EN-10 5000 Series Indicators Control Functions TABLE 1-5. CONTROL FUNCTIONS. Button ON/ZERO PRINT FUNCTION TARE Prmary Functon (Short Press) Turns the Indcator Sends the current value Intates an applcaton Performs a tare to the selected COM mode. operaton. ports f AUTOPRINT s If Indcator s On, sets set to Off. Temporarly dsplays the zero. actve mode’s reference data. In Wegh mode, temporarly dsplays 10x expanded resoluton. Units Mode Menu Secondary Functon (Long Press) Turns the Indcator off. Changes the weghng Allows changng the Enter the User menu.
INSTALLATION Unpacking Unpack the followng tems: • Capacty Label Sheet • T51P or T51XW Indcator • LFT Sealng kt • AC Power Cord (T51P only) • Instructon Manual CD • Mountng Bracket • Warranty Card • Knobs (2) External Connections ..1 Scale Base with Connector to T51P Ohaus bases wth a connector can be attached to the external load cell connector (Fgure 1-1, tem 14). Refer to secton 2.3.2 for bases wthout a connector. To make the connecton, plug the base connector onto the external load cell connector. Then rotate the base connector’s lockng rng clockwse. For connectng bases wth a connector to a T51XW (whch does not have the external connector), a Load Cell Cable Adapter Kt p/n 80500736 s avalable as an accessory. Ths kt connects to the termnal block nsde the T51XW and has an external connector on the other end. .. RS interface Cable to T51P Connection Connect the optonal RS232 cable to the RS232 connector (Fgure 1-1, tem 16). Fgure 2-1. RS232 Pns. .. AC Power to T51P Connect the AC power cord (suppled) to the power receptacle (Fgure 1-1, tem 11), then connect the AC plug to an electrcal outlet.
Page 14
BY AUTHORIZED AND QUALIFIED PERSONNEL, SUCH AS AN ELECTRICAL TECHNICIAN. T51P Remove the four Phllps head screws from the rear housng. Remove the front housng beng careful not to dsturb the nternal connectons. Once all connectons are made, reattach the front housng. T51XW Remove the four hex head screws from the rear housng. Open the housng by carefully pullng the front housng forward. Once all connectons are made, reattach the front housng. The screws should be tghtened to 2.5 N m (20-25 n-lb) torque to ensure a watertght seal. • Connection .. Scale Base Without Connector to T51P or T51XW Bases wthout a connector must be attached to the nternal load cell connector on the man J4-1 +EXE PC board. Pass the load cell cable through the stran relef (Fgure 1-1, tem 13 or Fgure 1-2, J4-2 +SEN tem 13) and attach t to termnal block J4 (Fgure 1-3, tem 2). Tghten the stran relef to J4-3 +SIG mantan a watertght seal. J4-4 J4-5...
5000 Series Indicators EN-1 .. RS Interface Cable to T51XW Connection Pass the optonal RS232 cable through the stran relef (Fgure 1-2, tem 10) and attach t to J7-1 termnal block J7 (Fgure 1-3, tem 6). Tghten the stran relef to mantan a watertght seal. J7-2 J7-3 J7-4 J7-5 .. Footswitch to T51P or T51XW Pass the optonal footswtch cable through the stran relef (Fgure 1-1, tem 15 or Fgure 1-2, tem 11) and attach t to termnal block J9 (Fgure 1-3, tem 5). T51P Rear Housing Orientation The T51P s delvered n the wall mount orentaton wth the connectons extng below the dsplay. The rear housng may be reversed so the connectons ext above the dsplay when the T51P s placed horzontally on a bench. To reverse the rear housng, remove the four Phllps head screws, carefully rotate the housng 180°, and renstall the screws. Fgure 2-3. Wall Mount Confguraton. Fgure 2-4. Bench Top Confguraton. Mounting Bracket Attach the bracket to a wall or table usng fasteners (not suppled) that are approprate for the type of mountng surface. The bracket wll accommodate up to 6 mm (1/4”) dameter screws. Locate the mountng holes as shown n Fgure 2-5. Fgure 2-5 Mountng Bracket Dmensons.
5000 Series Indicators EN-15 Menu Navigation Enter the menu by pressng the TARE Menu button untl MENU s dsplayed. When the button s released, the Legal for Trade status s dsplayed, followed by the frst menu. Press the No or Back button to move to a dfferent menu. Press the Yes button to enter the menu. Once n the menu, press the Yes button to vew the menu tem settng or press the No or Back button to move to the next menu tem. When vewng the settng, press the Yes button to accept the settng, or press the No or Back button to change the settng. Once all settngs have been made, press the Exit button to return to the current applcaton mode. For menu tems wth numerc settngs such as Capacty, the current settng s dsplayed wth all dgts flashng. Press the No button to begn edtng. The frst dgt s dsplayed flashng. Press the No button to ncrement the dgt or press the Yes button to accept the dgt and move to the next dgt. Repeat ths process for all dgts. Press the Yes button when the last dgt has been set. The new settng s dsplayed wth all dgts flashng. Press the Yes button to accept the settng or press the No button to resume edtng. Ths method also apples to settng Checkwegh under and over targets. For End menu tems, pressng the Yes button advances to the next menu, whle pressng the No button returns to the top of the current menu. Calibration Menu When CAL s dsplayed, press the Yes button to accept the Calbraton menu selecton. Press the No button to advance to the desred calbraton menu tem. Zero Perform Three calbraton processes are avalable: Zero Calbraton, Span Calbraton and Span Perform Lnearty Calbraton. Default settngs are bold.
EN-1 5000 Series Indicators ..1 Zero Calibration Zero calbraton uses one calbraton pont. The zero calbraton pont s establshed wth no weght on the scale. Use ths calbraton method to adjust for a dfferent pre-load wthout affectng the span or lnearty calbraton. When ZErO s dsplayed, press the Yes button to ntate Zero Calbraton. The dsplay flashes 0 and the calbraton unt. Press the Yes button to establsh the zero pont. The dsplay shows --C-- whle the zero pont s establshed. When zero calbraton s completed, the dsplay shows dONE. Then the scale exts to the actve weghng mode and dsplays the actual weght value. .. Span Calibration Span Calbraton uses two ponts to adjust the scale. The span calbraton pont s establshed wth a calbraton mass placed on the scale. The zero calbraton pont s establshed wth no weght on the scale. When SPAN s dsplayed, press the Yes button to ntate Span Calbraton. The dsplay flashes the span calbraton pont. Place the specfed weght on the scale and press the Yes button. To choose a dfferent span pont or calbraton unt, edt the settng as explaned n Secton 3.2 Menu Navgaton. When the desred settng s dsplayed, place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the span pont s establshed. The dsplay flashes 0. Wth no weght on the scale, press the Yes button to establsh the zero pont. The dsplay shows --C-- whle the zero pont s establshed. When span calbraton s completed, the dsplay shows dONE. Then the scale exts to the actve weghng mode and dsplays the actual weght value. ...
5000 Series Indicators EN-1 .. Linearity Calibration Lnearty calbraton uses 3 calbraton ponts. The full calbraton pont s establshed wth a weght on the scale. The md calbraton pont s establshed wth a weght equal to half of the full calbraton weght on the scale. The zero calbraton pont s establshed wth no weght on the scale. The md calbraton ponts cannot be altered by the user durng the calbraton procedure. When LINEAr s dsplayed, press the Yes button to ntate Lnearty Calbraton. The dsplay flashes the full calbraton pont and calbraton unt. Place the specfed weght on the scale and press the Yes button. To choose a dfferent full pont or calbraton unt (kg or lb), edt the settng as explaned n Secton 3.2 Menu Navgaton. When the desred settng s dsplayed, place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the full pont s establshed. The dsplay flashes the md calbraton pont. Place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the md pont s establshed. The dsplay flashes 0. Wth no weght on the scale, press the Yes button to establsh the zero pont. The dsplay shows --C-- whle the zero pont s establshed. When lnearty calbraton s completed, the dsplay shows dONE. Then the scale exts to the actve weghng mode and dsplays the actual weght value. ...
EN-1 5000 Series Indicators .. Calibration Test Calbraton test s used to compare a known calbraton weght aganst the stored span calbraton data. NOTE: Calbraton Test s always avalable (even when LFT s set to ON). When tESt s dsplayed, press the Yes button to ntate Calbraton Test. The dsplay flashes 0. Wth no weght on the scale, press the Yes button to record the current zero pont. The dsplay shows --t-- whle the zero pont s recorded. The dsplay flashes the span calbraton weght usng the value from the last calbraton. The example shows test weght of 30 kg. Place the specfed test weght on the scale and press the Yes button. The dsplay shows --t-- whle the data s processed. The dsplay flashes the actual dfference between the calbraton data and the test weght. The example shows a 0.010 kg dfference. The result of the Calbraton Test s prnted. After 5 seconds, Calbraton Test ends, the scale returns to the actve weghng mode and dsplays the current weght. ..5 Geographical Adjustment Factor Refer to Table 3-2 and set the GEO factor that corresponds to your locaton. 00 to 31 NOTE: Only an authorzed manufacturer’s representatve or certfed verfcaton personnel may make these • • changes. Changng the geographcal settng alters the calbraton values. • .. End Calibration Advance to the next menu.
Page 21
5000 Series Indicators EN-1 TABLE -. GEOGRAPHICAL ADJUSTMENT VALUES Elevaton above sea level n meters Geographcal lattude 0 325 650 975 1300 1625 1950 2275 2600 2925 3250 away from the equator, 325 650 975 1300 1625 1950 2275 2600 2925 3250 3575 (North or South) n Elevaton above sea level n feet 0 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660...
EN-0 5000 Series Indicators Setup Menu When the Indcator s used for the frst tme, enter ths Reset No, Yes menu to set the Range, Capacty and Graduaton. Default Range Single, Dual settngs are bold. Full Scale Capacty 1…999950 Graduaton 0.00001…1000 Power On unt Auto, kg, g, lb, oz, lb:oz Zero Range 2%, 100% Auto-Tare Off, On, Accept Retan Weght Data Off, On...
5000 Series Indicators EN-1 .. Graduation Set the scale readablty. 0.00001, 0.00002, 0.00005, 0.0001, 0.0002, 0.0005, 0.001, 0.002, 0.005, 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 50, 100, 200, 500, 1000. • NOTE: Graduaton settngs are lmted to values from Capacty dvded by 1000 to Capacty dvded by • 30000. Therefore, not all settngs are avalable for each capacty. • NOTE: If dUAL was selected n the rANGE menu tem, the Graduaton settng defnes the Range 1 graduaton. The Range 2 graduaton s automatcally defned as one step greater than the Graduaton settng. For example, f Graduaton s set to 0.001, the Range 2 graduaton becomes 0.002. NOTE: Range 2 graduaton s retaned even under half capacty untl the scale returns to zero. ..5 Power On Unit Set the unt of measures dsplayed at startup AUtO = last unt n use when turned off PWr.UN kg = klograms PWr.UN g = grams PWr.UN lb = pounds PWr.UN oz = ounces PWr.UN lb:oz = pound ounces PWr.UN t = tonnes PWr.UN C = custom unt...
EN- 5000 Series Indicators .. Auto-Tare Set the Automatc Tare functonalty. OFF = Automatc Tare s dsabled. ON = the frst stable gross weght wll be tared. ACCEPt = when the applcaton mode s CHECK, stable gross weght that s wthn the Checkwegh accept lmts wll be tared. When Accept s selected, set the current delay tme s dsplayed. Settngs: OFF = automatc tare takes affect mmedately 0.5, 1, 2 or 5 = automatc tare takes affect after the selected delay perod (n seconds). .. Retain Weight Data Set the Retan Weght Data functonalty. OFF = Dsabled. ON = When power s turned on, the dsplayed weght s based on the last stored zero (Zero button or “Z” command).
5000 Series Indicators EN- ..10 Beeper Volume Set the beeper volume. OFF = dsabled. LOW = soft HI = loud. ..11 Beeper Signal Set how the beeper responds n the Checkwegh mode. OFF = the beeper s dsabled. ACCEPt = the beeper wll sound when the weght s wthn the Accept range. UNdEr = the beeper wll sound when the weght s below the Under settng. OVEr = the beeper wll sound when the weght s above the Over settng. UNd.OVr = the beeper wll sound when the weght s below the Under settng or above the Over settng.
EN- 5000 Series Indicators .5.1 Reset Set the Readout menu to factory default settngs. NO = not reset YES = reset If the Legal for Trade menu tem s set to ON, the Stable Range, Averagng Level, Auto Zero Trackng, Auto Off and Gross settngs are not reset. .5. Stable Range Set the amount the readng can vary before the stablty symbol turns off. 0.5d = 0.5 scale dvson 1d = 1 scale dvson 2d = 2 scale dvsons 3d = 3 scale dvsons 5d = 5 scale dvsons NOTE: When LFT s set to ON, the settng s forced to 1 d. The settng s locked when the hardware lock swtch s set to the ON poston.
5000 Series Indicators EN-5 .5.5 Backlight Set the dsplay backlght functonalty. OFF = always off. ON = always on. AUtO = turns on when a button s pressed or the dsplayed weght changes. When Auto s selected, set Backlght shut off tme. Settngs: SEt 1 = backlght turns off after 1 mnute of no actvty. SEt 2 = backlght turns off after 2 mnute of no actvty. SEt 5 = backlght turns off after 5 mnute of no actvty. .5. Auto Off Timer Set the automatc shut off functonalty.
EN- 5000 Series Indicators ..1 Reset Set the Mode menu to the factory defaults. NO = not reset. YES = reset. NOTE: If the Legal for trade menu tem s set ON, the settngs are not reset. .. Weighing Mode Set the status. OFF = Dsabled ON = Enabled .. Parts Counting Mode Set the status. OFF = Dsabled ON = Enabled .. Parts Counting Optimize Set the status.
5000 Series Indicators EN- .. Check Weighing Mode Set the status. OFF = Dsabled ON = Enabled .. End Mode Advance to the next menu. Unit Menu Enter ths menu to actvate the desred unts. Default settngs are Reset No, Yes bold. Klograms Off, On Pounds Off, On Note: Due to natonal laws, the ndcator may not nclude some of...
EN- 5000 Series Indicators .. Gram Unit Set the status. OFF = Dsabled ON = Enabled ..5 Ounce Unit Set the status. OFF = Dsabled ON = Enabled NOTE: Ounce Unt s not avalable when Range s set to Dual. .. Pound Ounce Unit Set the status. OFF = Dsabled ON = Enabled NOTE: Pound Ounce Unt s not avalable when Range s set to Dual.
EN-0 5000 Series Indicators .. Date Set Set the date. 00 to 99 = year poston 01 to 12 = month poston 01 to 31 = day poston Refer to Secton 3.2 Menu Navgaton to enter settngs. .. Time Type Set the tme format. 24 hr = 24 hour format. 12 hr = 12 hour format. ..5 Time Set Set the tme. 24 hour format 00 to 23 = hour poston (current tme blnkng) 00 to 59 = mnute poston (Set hours 00 to 23) (Set mnutes 00 to 59) 12 hour format 12 A to 12 P = hour poston 00 to 59 = mnute poston (current tme blnkng) Refer to Secton 3.2 Menu Navgaton to enter settngs.
5000 Series Indicators EN-1 .. User ID Set the user dentfcaton. 000000 to 999999 Refer to Secton 3.2 Menu Navgaton to enter settngs. .. Project ID Set the Project dentfcaton. 000000 to 999999 Refer to Secton 3.2 Menu Navgaton to enter settngs. .. Scale ID Set the Scale dentfcaton. 000000 to 999999 Refer to Secton 3.2 Menu Navgaton to enter settngs. .. End GMP Advance to the next menu.
EN- 5000 Series Indicators Print1 and Print Menus Enter ths menu to defne prntng parameters. Default settngs are bold. NOTE: The Prnt2 menu s only dsplayed f a second nterface (RS232 or RS422/RS485) s nstalled. Reset No, Yes ..1 Reset Stable Only Off, On Set the Prnt menu to factory defaults. Auto Prnt Off, NO = not reset. On Stable (-> Load, Load and Zero), Interval (-> 0…3600), Contnuous, YES = reset. On Accept Prnt Content Result (-> Off, On, Numerc only), Gross (-> Off, On),...
5000 Series Indicators EN- When ON.StAb s selected, set the condton for prntng, where: LOAd = prnts when the load s stable and greater than zero LOAd.Zr = prnts when any load s stable and equal to or greater than zero. When INtEr s selected, set the Prnt Interval. 1 to 3600 (seconds) .. Print Content Sub-menu Ths sub-menu s used to defne the content of the prnted data. Result Set the status. OFF = Dsabled ON = the dsplayed readng s prnted. NUM = only the numerc porton of the dsplayed readng s prnted. Gross Set the status. OFF = Dsabled. ON = the Gross weght s prnted. Set the status. OFF = Dsabled.
Page 36
EN- 5000 Series Indicators Project ID Set the status. OFF = Dsabled. ON = the Project ID s prnted. Scale ID Set the status. OFF = Dsabled. ON = the Scale ID s prnted. Time Set the status. OFF = Dsabled. ON = the Date and Tme s prnted. Difference Set the status. OFF = Dsabled.
LINE = move paper up one lne after prntng 4.LINE = move paper up four lnes after prntng FOrM = a form feed s appended to the prntout .. Output Set the format of the seral output strng to a prnter or computer. DEF = use the default output format of the T51 ndcator (see Secton 5.2 Output Format). C11 = use the output format of the Ohaus CD/CW-11 ndcators (see respectve CD-11/CW-11 user manuals). .. List Menu Settings Prnt the menu settngs. NO = do not prnt. YES = prnt. .. End Print1 or End Print Advance to the next menu.
EN- 5000 Series Indicators .10.1 Reset Set the COM1 and COM2 menu to factory defaults. NO = not reset. YES = reset. .10. Baud Set the Baud rate. 300 = 300 bps 600 = 600 bps 1200 =1200 bps 2400 = 2400 bps 4800 = 4800 bps 9600 = 9600 bps 19200 = 19200 bps .10. Parity Set the data bts and party.
5000 Series Indicators EN- .10. Alternate Command Sub-menu Enter ths sub-menu to set a dfferent command character for the P (Prnt), T (Tare) and Z (Zero) commands. Alternate Print Command Set the alternate command character for Prnt. A to Z. Alternate Tare Set the alternate command character for Tare. A to Z. Alternate Zero Set the alternate command character for Zero. A to Z. .10. End COM1 or End COM Advance to the next menu. .11 I-O Menu Enter ths menu to set the optonal nput and output devce parameters. Reset No, Yes Default settngs are bold.
EN- 5000 Series Indicators .11. External Input Set the functon to be controlled by an optonal external nput devce such as a foot swtch. OFF = dsabled. tArE = Tare functon. ZErO = Zero functon. PrINt = Prnt functon. FUNCt = acton specfc to the current applcaton mode. S-S = the frst external nput changes the state of the relay. The second external nput (Start-Stop) returns the relay to the orgnal state.
5000 Series Indicators EN- Contact Set the tmng of the relay contacts. SIM = relays open or close at the same tme. b-b-M = relay opens before the next relay closes (break before make). M-b-b = relay closes before the next relay opens (make before break). NOTE: A 100 ms delay or over-lap s used for the break-before-make and make-before-break tmng. Stable Set how the relay outputs react durng nstablty. OFF = relay changes are mmedate. ON = delays relay changes untl weght readng s stable. .11.5 End I-O Advance to the next menu. .1 Menu Lock Menu Use ths menu to prevent unauthorzed changes to menu settngs. When the securty Reset No, Yes Lock Calbraton Menu Off, On swtch s set to ON, the locked menus can be vewed but not changed. Default settngs Lock Setup Menu Off, On...
EN-0 5000 Series Indicators .1. Lock Setup Set the status. OFF = Setup menu s not locked. ON = Setup menu s locked. .1. Lock Readout Set the status. OFF = Readout menu s not locked. ON = Readout menu s locked. .1.5 Lock Mode Set the status. OFF = Mode menu s not locked. ON = Mode menu s locked. .1. Lock Unit Set the status.
5000 Series Indicators EN-1 .1.11 Lock GMP Set the status. OFF = GMP menu s not locked. ON = GMP menu s locked. .1.1 Lock I-O Set the status. OFF = I-O menu s not locked. ON = I-O menu s locked. .1.1 End Lock Advance to the next menu. .1 Key Lock Menu Use ths menu to prevent unauthorzed access to button functons. When Reset No, Yes the securty swtch s set to ON, the locked buttons are dsabled. Default...
EN- 5000 Series Indicators .1.5 Lock Print Button Set the status. OFF = Prnt button s unlocked. ON = Prnt button s locked. .1. Lock Unit Button Set the status. OFF = Unt button s unlocked. ON = Unt button s locked. .1. Lock Function Button Set the status. OFF = Functon button s unlocked. ON = Functon button s locked.
5000 Series Indicators EN- OPERATION Turning Indicator On/Off To turn the Indcator on, press the ON/ZERO Off button. The Indcator performs a dsplay test followed by a seres of nformatonal dsplays, and then enters the actve weghng mode. To turn the Indcator off, press and hold the ON/ZERO Off button untl OFF s dsplayed. Zero Operation Zero can be set under the followng condtons: • Automatcally at Power On (ntal zero). • Sem-automatcally (manually) by pressng the ON/ZERO Off button. • Sem-automatcally by sendng the Zero command (Z or alternate zero command). Press the ON/ZERO Off button to zero the weght dsplay. The scale must be stable to accept zero operaton. Manual Tare When weghng an tem that must be held n a contaner, tarng stores the contaner weght n memory. Place the empty contaner on the scale (example 0.5 kg) and press the TARE button. The dsplay wll show the net weght. To clear the Tare value, empty the scale and press the TARE button. The dsplay wll show the gross weght. Pre-Set Tare A Pre-set Tare (PT) s a known tare value entered usng the xT command (example 1.234 kg).
EN- 5000 Series Indicators Changing Units of Measure Press and hold the PRINT Units button untl the desred measurng unt appears. Only measurng unts enabled n the Unt Menu wll be dsplayed (refer to Secton 3.7). Printing Data Prntng the dsplayed data to a prnter or sendng the data to a computer requres that the communcaton parameters n the Prnt and Communcaton Menu are set (refer to Sectons 3.9 and 3.10). Press the PRINT Units button to send the dsplayed data to the communcaton port (the Auto-Prnt Mode n Secton 3.9 functon must be Off). Application Modes Press and hold the FUNCTION Mode button untl the desred applcaton mode appears. Only modes enabled n the mode menu wll be dsplayed (refer to Secton 3.6). ..1 Weighing Place the tem to be weghed on the scale. The llustraton ndcates a sample of 1.5 kg, Gross weght. NOTE: Press the FUNCTION Mode button to temporarly dsplay the weght n 10x expanded resoluton. .. Parts Counting Use ths mode to count parts of unform weght. The Indcator determnes the quantty based on the average weght of a sngle part. All parts must be unform n weght for accurate measurements.
5000 Series Indicators EN-5 Establishing a New APW Press the No button to ncrement the sample sze. Choces are 5, 10, 20, 50 and 100. To establsh the APW, place the specfed quantty of samples on the scale and press the FUNCTION Mode button to capture the weght. APW s dsplayed shortly followed by the APW value wth the current unt of measure. Begin Counting Place the parts on the scale and read the count. If a contaner s used, be sure to tare the empty contaner frst. .. Percent Weighing Use ths mode to measure the weght of a sample as a percentage of a reference weght. Reference Weight (Ref Wt) When the FUNCTION Mode button s released, CLr.rEF% s dsplayed. Clearing a Stored Reference Weight Press the Yes button to clear the stored reference weght. Recalling a Stored Reference Weight Press the No button to recall the exstng reference weght.
EN- 5000 Series Indicators .. Check Weighing Use ths mode to determne f the weght of a sample s wthn prescrbed lmts. Checkweighing Limits When the FUNCTION Mode button s released, CLr.rEF s dsplayed. Clearing Stored Check Weighing Limits Press the Yes button to clear the stored lmts. Recalling Stored Check Weighing Limits Press the No button to recall the stored lmts. NOTE: Press the FUNCTION Mode button to temporarly dsplay the Under and Over Lmt values. Editing the Under Setting The dsplay shows SEt.LO. Press the Yes button to edt settng.. Settngs: -999950 to 999950 Refer to Menu Navgaton Secton 3.2 to enter settngs. NOTE: The mnus sgn s used together wth the frst dgt to show a negatve value. Editing the Over Setting The dsplay shows SEt.HI.
5000 Series Indicators EN- ..5 Dynamic Weighing Use ths mode to wegh movng or overszed objects. The weght s held on the dsplay untl reset. Manual, sem-automatc and automatc start/stop methods are avalable (refer to Secton 3.6.6). Begin Dynamic Weighing When the dsplay shows rEAdY, place the object on the scale. If the manual mode s n use, press the FUNCTION Mode button to start measurement. If the sem-automatc or automatc mode s n use, measurement s started automatcally. • NOTE: When usng manual mode, t s not necessary for the dsplay to be at zero gross or net. When usng • sem-automatc or automatc mode, the dsplay must be at zero gross or net before placng the object on • the scale. The example s for a settng of 5 seconds. Durng the averagng perod, the countdown tmer decreases n one second ncrements. NOTE: If SEt 0 was selected n the Dynamc menu tem, the countdown tmer s not dsplayed. When the countdown has completed, the readngs are averaged and held on the dsplay. The averaged weght s dsplayed untl reset. If the manual or sem-automatc mode s n use, reset the countdown tmer by pressng the FUNCTION Mode button. Then the dsplay shows rEAdY. If the automatc mode s n use, the held readng s shown on the dsplay for 10 seconds after the object s removed to wthn 5 dvsons of zero. Then the dsplay shows rEAdY. The scale s now ready to accept a new object.
EN- 5000 Series Indicators SERIAL COMMUNICATION The T51P and T51XW Indcators nclude an RS232 seral communcaton nterface. The setup of RS232 operatng parameters are more fully explaned n Secton 3.10. The physcal hardware connecton s explaned n Secton 2.6. The nterface enables dsplay and GMP data to be sent to a computer or prnter. A computer can be used to control some functons of the ndcator usng the commands lsted n Table 5-1. Interface Commands Communcate to the ndcator usng the command characters lsted n Table 5-1. TABLE 5-1. SERIAL INTERFACE COMMAND TABLE. Command Function Character Immedate Prnt of dsplayed weght (stable or unstable). Prnt dsplayed weght (stable or unstable). Contnuous Prnt. Prnt on Stablty. Interval Prnt x = Prnt Interval (1-3600 sec) Same as pressng Zero button Same as pressng Tare button Enter a preset tare, where x = the tare value n grams. Prnt current unt: g, kg, lb, oz, lb:oz, t, C (custom) Set scale to unt x: 1=g, 2=kg, 3=lb, 4=oz, 5=lb:oz, 6=t, 7=C Verson: prnt name, software revson and LFT ON (f LFT s set ON). H x “text” Enter Header lne , where x = lne number 1 to 5, “text” = header text up to 24 alphanumerc characters Esc R Global reset to reset all menu settngs to the orgnal factory defaults Prnt stable only. Where x=0 Off, x=1 On.
Printouts The followng sample prnt outs are generated by the Print button, “P” Command or alternate prnt command. The content of the prntout s defned n the Prnt Content menu tem. A maxmum of 24 characters can be prnted on each lne. NOTE: Shaded areas = ths date s prnted when set on n the Prnt Content menu. Unshaded = typcal Weigh Mode Printout Count Mode Printout Percent Mode Printout Ohaus Corporation Ohaus Corporation Ohaus Corporation 19A Chapin Road 19A Chapin Road 19A Chapin Road P.O. Box 2033 P.O. Box 2033 P.O. Box 2033 Pine Brook, NJ, 07058 USA...
Page 52
EN-50 5000 Series Indicators Dynamic Mode Printout Check Weighing Mode Printout Calibration Test Printout Ohaus Corporation Ohaus Corporation --------- Cal Test --------- 19A Chapin Road 19A Chapin Road Ohaus Corporation P.O. Box 2033 P.O. Box 2033 19A Chapin Road Pine Brook, NJ, 07058 USA Pine Brook, NJ, 07058 USA P.O.
5000 Series Indicators EN-51 LEGAL FOR TRADE When the ndcator s used n trade or a legally controlled applcaton t must be set up, verfed and sealed n accordance wth local weghts and measures regulatons. It s the responsblty of the purchaser to ensure that all pertnent legal requrements are met. Settings Before verfcaton and sealng, perform the followng steps: 1. Verfy that the menu settngs meet the local weghts and measures regulatons. 2. Perform a calbraton as explaned n Secton 3. 3. Set Legal for Trade to ON n the Setup menu. 4. Wthout extng the menu, turn the ndcator off. 5. Dsconnect power from the ndcator and open the housng as explaned n Secton 2.3.1. 6. Set the poston of the securty swtch SW2 to ON as shown n Fgure 1-3, tem 4. 7. Close the housng. 8. Reconnect power and turn the ndcator on. NOTE: When Legal for Trade s set to ON and the securty swtch s set to ON, the followng menu settngs cannot be changed: Zero Calbraton, Span Calbraton, Lnearty Calbraton, GEO, Range, Capacty, Graduaton, Power On Unt, Zero Range, Auto Tare, Retan Weght, Legal for Trade, Stable Range, Auto Zero Trackng, Gross Indcator, Modes, Unts, Stable Only. Verification The local weghts and measures offcal or authorzed servce agent must perform the verfcaton procedure. Sealing The local weghts and measures offcal or authorzed servce agent must apply a securty seal to prevent tamperng wth the settngs. Refer to the llustratons below for sealng methods. Fgure 6-1. T51P Wre Seal Fgure 6-2. T51XW Wre Seal...
Page 54
EN-5 5000 Series Indicators Fgure 6-3. T51P Paper Seal Fgure 6-4. T51XW Paper Seal When the scale base s attached to the ndcator usng a connector, t s necessary to seal the load cell cable to the ndcator n some jursdctons. The load cell sealng collar P/N 80500737 (Fgure 6-5) s avalable as an accessory. Fgure 6-5. Load Cell Sealng Collar...
5000 Series Indicators EN-5 MAINTENANCE CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE CLEANING. Model T51P Cleaning • The housng may be cleaned wth a cloth dampened wth a mld detergent f necessary. • Do not use solvents, chemcals, alcohol, ammona or abrasves to clean the housng or control panel. Model T51XW Cleaning • Use approved cleanng solutons for the stanless-steel Indcator housng and rnse wth water. Dry thoroughly. • Do not use solvents, chemcals, alcohol, ammona or abrasves to clean the control panel. Troubleshooting TABLE -1. TROUBLESHOOTING. SYMPTOM PROBABLE CAUSE(s) REMEDY Unt wll not turn on. Power cord not plugged n or properly Check power cord connectons. Make sure connected. power cord s plugged n properly nto the power outlet. Power outlet not supplyng electrcty.
EN-5 5000 Series Indicators TABLE -1. TROUBLESHOOTING (Cont.). SYMPTOM PROBABLE CAUSE(s) REMEDY Error 9.5 Calbraton data not present. Calbrate scale. Battery symbol flashng Batteres are dscharged. Replace batteres (T51P). CAL E Calbraton value outsde allowable lmts Use correct calbraton weght. NO.SW Attemptng to ext the menu wth the LFT Refer to Secton 6.1. Set the securty swtch settng ON and the securty swtch OFF. to the ON poston. REF WT Err Reference Weght too small. The weght on Use a greater weght for sample. the platform s too small to defne a vald reference weght. Service Information If the troubleshootng secton does not resolve your problem, contact an authorzed Ohaus Servce Agent. For Servce assstance n the Unted States, call toll-free 1-800-526-0659 between 8:00 AM and 5:00 PM Eastern Standard Tme. An Ohaus Product Servce Specalst wll be avalable to assst you. Outsde the USA, please vst our webste www.ohaus.com to locate the Ohaus offce nearest you.
5000 Series Indicators EN-55 TECHNICAL DATA Specifications Materials T51XW Housng: stanless-steel T51P Housng: ABS plastc Dsplay wndow: polycarbonate Keypad: polyester Feet: Rubber Ambient conditions The techncal data s vald under the followng ambent condtons: Ambent temperature: -10°C to 40°C / 14°F to 104°F Relatve humdty: Maxmum relatve humdty 80% for temperatures up to 31°C decreasng lnearly to 50% relatve humdty at 40°C. Heght above sea level: up to 2000m Operablty s assured at ambent temperatures between -10°C and 40°C.
EN-5 5000 Series Indicators Accessories and Options TABLE -. OPTIONS. DESCRIPTION PART NUMBER AC Relay Kt 80500720 Base Mount Kt , T51P 80500722 Column Mount Kt, 35 cm panted steel 80500723 Column Mount Kt, 68 cm panted steel 80500724 Column Mount Kt, 35 cm stanless steel 80500725 Column Mount Kt, 68 cm stanless steel 80500726 DC Relay Kt 80500727 Rechargeable Battery Kt 80500729 RS422/485 Interface Kt 80500731 RS232 Interface kt 80500733 TABLE -. ACCESSORIES. DESCRIPTION PART NUMBER...
EN-5 5000 Series Indicators Compliance Complance to the followng standards s ndcated by the correspondng markng on the product. Marking Standard Ths product conforms to the EMC Drectve 2004/108/EC, the Low Voltage Drectve 2006/95/EC and the Non-automatc Weghng Instruments Drectve 2009/23/EC. The complete Declaraton of Conformty s avalable from Ohaus Corporaton. UL60950-1: 2003 AS/NZS4251.1, AS/NZS4252.1 EU Emissions Note Ths devce comples wth EN55011 / CISPR 11 Class A Group 1. FCC Note Ths equpment has been tested and found to comply wth the lmts for a Class A dgtal devce, pursuant to Part 15 of the FCC Rules. These lmts are desgned to provde reasonable protecton aganst harmful nterference when the equpment s operated n a commercal envronment. Ths equpment generates, uses, and can radate rado frequency energy and, f not nstalled and used n accordance wth the nstructon manual, may cause harmful nterference to rado communcatons. Operaton of ths equpment n a resdental area s lkely to cause harmful nterference n whch case the user wll be requred to correct the nterference at hs own expense. Industry Canada Note Ths Class A dgtal apparatus comples wth Canadan ICES-003. Cet apparel numérque de la classe A est conforme à la norme NMB-003 du Canada. ISO 001 Registration In 1994, Ohaus Corporaton, USA, was awarded a certfcate of regstraton to ISO 9001 by Bureau Vertus Qualty Internatonal (BVQI), confrmng that the Ohaus qualty management system s complant wth the ISO 9001 standard’s requrements. On May 15, 2003, Ohaus Corporaton, USA, was re-regstered to the ISO 9001:2000 standard.
Page 61
5000 Series Indicators EN-5 Important Notice for verified weighing instruments Weghng Instruments verfed at the place of manufacture bear one of the precedng marks on the pack- ng label and the green ‘M’ (metrology) stcker on the descrptve plate. They may be put nto servce mmedately. Weghng Instruments to be verfed n two stages have no green ‘M’ (metrology) on the descrptve plate and bear one of the precedng dentfcaton mark on the packng label. The second stage of the ntal verfcaton must be carred out by the approved servce organzaton of the authorzed representatve wthn the EC or by the natonal weghts & measures (W+M) authortes. The frst stage of the ntal verfcaton has been carred out at the manufacturer’s work. It comprses all tests accordng to the adopted European standard EN 45501:1992, paragraph 8.2.2. If natonal regulatons lmt the valdty perod of the verfcaton, the user of the weghng nstrument must strctly observe the re-verfcaton perod and nform the respectve W+M authortes. Disposal In conformance wth the European Drectve 2002/96/EC on Waste Electrcal and Electronc Equpment (WEEE) ths devce may not be dsposed of n domestc waste. Ths also apples to countres outsde the EU, per ther specfc requrements. The Batteres Drectve 2006/66/EC ntroduces new requrements from September 2008 on removablty of batteres from waste equpment n EU Member States. To comply wth ths Drectve, ths devce has been desgned for safe removal of the batteres at end-of-lfe by a waste treatment faclty. Please dspose of ths product n accordance wth local regulatons at the collectng pont specfed for electrcal and electronc equpment. If you have any questons, please contact the responsble authorty or the dstrbutor from whch you purchased ths devce. Should ths devce be passed on to other partes (for prvate or professonal use), the content of ths regulaton must also be related. For dsposal nstructons n Europe, refer to www.ohaus.com/weee. Thank you for your contrbuton to envronmental protecton.
Page 62
LIMITED WARRANTY Ohaus products are warranted aganst defects n materals and workmanshp from the date of delvery through the duraton of the warranty perod. Durng the warranty perod Ohaus wll repar, or, at ts opton, replace any component(s) that proves to be defectve at No charge, provded that the product s returned, freght prepad, to Ohaus. Ths warranty does Not apply f the product has been damaged by accdent or msuse, exposed to radoactve or corrosve materals, has foregn materal penetratng to the nsde of the product, or as a result of servce or modfcaton by other than Ohaus. In leu of a properly returned warranty regstraton card, the warranty perod shall begn on the date of shpment to the authorzed dealer. No other express or mpled warranty s gven by Ohaus Corporaton. Ohaus Corporaton shall Not be lable for any consequental damages. As warranty legslaton dffers from state to state and country to country, please contact Ohaus or your local Ohaus dealer for further detals.
Need help?
Do you have a question about the T51P and is the answer not in the manual?
Questions and answers