OHAUS 3000 Series T32XW Instruction Manual
  1. Manuals
  2. Brands
  3. OHAUS Manuals
  4. Touch Panel
  5. 3000 Series T32XW
  6. Instruction manual

OHAUS 3000 Series T32XW Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
This document hosted by: www.oldwillknottscales.com
3000 Series Indicators
Instruction Manual
T32XW Indicator


Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3000 Series T32XW and is the answer not in the manual?

Questions and answers

Related Manuals for OHAUS 3000 Series T32XW

Summary of Contents for OHAUS 3000 Series T32XW

  • Page 1 This document hosted by: www.oldwillknottscales.com 3000 Series Indicators Instruction Manual T32XW Indicator...

  • Page 3: Table Of Contents

    3000 Series Indicators EN- TABLE OF CONTENTS 1. INTRODUCTION ............................EN-4 1.1 Safety Precautons .............................EN-4 1.2 Overvew of Parts and Controls ........................EN-5 1.3 Control Functons ............................EN-8 2. INSTALLATION ............................EN-9 2.1 Unpackng ..............................EN-9 2.2 External Connectons ..........................EN-9 2.2.1 RS232 Interface Cable to the ndcator ....................EN-9 2.2.2 AC Power ............................EN-9 2.2.3 Battery power ..........................EN-10 2.2.4 Mountng Bracket to the ndcator .....................EN-10 2.3 Internal Connectons .
  • Page 4 EN-2 3000 Series Indicators TABLE OF CONTENTS (Cont.) 3.5 Readout Menu ............................EN-20 3.5.1 Reset ............................EN-22 3.5.2 Flter ............................EN-21 3.5.3 Auto-Zero Trackng ........................EN-21 3.5.4 Backlght .............................EN-21 3.5.5 Auto Off Tmer ..........................EN-21 3.5.6 End Readout ..........................EN-21 3.6 Mode Menu .............................EN-22 3.6.1 Reset ............................EN-22 3.6.2 Parts Countng Mode ........................EN-22 3.6.3 End Mode ............................EN-22 3.7 Unt Menu ...............................EN-23 3.7.1 Reset .
  • Page 5 3000 Series Indicators EN-3 TABLE OF CONTENTS (Cont.) 3.10 Securty Swtch ............................EN-27 4. OPERATION .............................EN-27 4.1 Turnng Indcator On/Off ..........................EN-27 4.2 Zero Operaton ............................EN-27 4.3 Manual Tare ............................EN-27 4.4 Changng Unts of Measure ........................EN-28 4.5 Prntng Data ............................EN-28 4.6 Applcaton Modes ...........................EN-28 4.6.1 Weghng .............................EN-28 4.6.2 Parts Countng ..........................EN-28 5. SERIAL COMMUNICATION ..........................EN-30 5.1 Interface Commands ..........................EN-30 5.2 Output Format ............................EN-31 6. LEGAL FOR TRADE ...........................EN-32 6.1 Settngs ..............................EN-32...

  • Page 6: Introduction

    EN- 3000 Series Indicators INTRODUCTION Ths manual contans nstallaton, operaton and mantenance nstructons for the T32XW Indcator. Please read ths manual completely before nstallaton and operaton. Safety Precautions For safe and dependable operaton of ths equpment, please comply wth the followng safety precautons: • Verfy that the nput voltage range prnted on the data label matches the local AC power to be used. • Make sure that the power cord does not pose a potental obstacle or trppng hazard. • Use only approved accessores and perpherals. • Operate the equpment only under ambent condtons specfed n these nstructons. • Dsconnect the equpment from the power supply before cleanng. • Do not operate the equpment n hazardous or unstable envronments. • Do not mmerse the equpment n water or other lquds. • Servce should only be performed by authorzed personnel. • The Indcator s suppled wth a grounded power cable. Use only wth a compatble grounded power outlet...

  • Page 7: OvervEw Of Parts And Controls

    3000 Series Indicators EN- Overview of Parts and Controls TABLE -. T32XW PARTS. Item Description Data Label Front Housng Adjustng Knob (2) Control Panel Mountng Bracket Screw (4) Rear Housng Safety Data Label Stran Relef for RS232 Stran Relef for Load Cell Cable Power cord Fgure 1-1. Indcator.
  • Page 8 EN- 3000 Series Indicators Overview of Parts and Controls (Cont.) LFT OFF LFT ON Fgure 1-2. Man PC Board. TABLE -2. MAIN PC BOARD. Item Description LOAD CELL WIRING Keypad Connector J8 Battery Connector Lne Power Input Sense Jumper W2 Load Cell Termnal Block J5 +EXC +SIG -SIG -EXC Sense Jumper W1 +SENS -SENS RS232 Termnal Block J7 LFT On / Off Swtch RS232 WIRING...
  • Page 9 3000 Series Indicators EN- Overview of Parts and Controls (Cont.) Fgure 1-3. Controls and Indcators. TABLE -3. CONTROL PANEL. Designation Capacty Label Wndow Pound symbol Ounce symbol Klogram, gram symbols TARE Menu button TARE symbol FUNCTION Mode button NET symbol PCS symbol PRINT Unts button Calbraton Mode symbol Battery symbol ON/ZERO Off button Center of Zero symbol Stable weght ndcator...

  • Page 10: Control FunctOns

    EN- 3000 Series Indicators Control Functions TABLE -. CONTROL FUNCTIONS. Button ON/ZERO PRINT FUNCTION TARE Prmary Functon (Short Press) If Indcator s On, sets Sends the current value Intates an applcaton Performs a tare zero. to the COM port f mode. operaton. AUTOPRINT s set to Off. Secondary Functon Units Mode Menu (Long Press) Turns the Indcator on Changes the weghng Allows changng the Enter the User menu. or off. Unt. applcaton mode. Vew the Audt Tral event Press and hold allows counters (extended scrollng through modes.

  • Page 11: Installation

    3000 Series Indicators EN- INSTALLATION Unpacking Unpack the followng tems: • Indcator • Mountng Bracket • Knobs (2) • Capacty Label Sheet • Instructon Manual CD • Warranty Card • LFT sealng Kt External Connections 2.2. RS232 interface Cable to the indicator Connect the optonal RS232 cable to the RS232 connector Fgure 1-1, tem 9). Connection Fgure 2-1. RS232 Pns. 2.2.2 AC Power Connect the AC plug to a properly grounded electrcal outlet.

  • Page 12: Battery Power

    The ndcator can operate for up to 100 hours on a fully charged battery. Durng battery operaton, a flashng trangle above the battery functon symbol ndcates the battery s low and requres rechargng. Approxmately 60 mnutes of operaton wll reman when the battery symbol starts to blnk. The ndcator wll dsplay Lo.BAT and automatcally turn off when the battery s fully dscharged. CAUTION BATTERY IS TO BE REPLACED ONLY BY AN AUTHORIZED OHAUS SERVICE DEALER. RISK OF EXPLOSION CAN OCCUR IF REPLACED WITH THE WRONG TYPE OR CONNECTED IMPROPERLY. Dspose of the lead acd battery accordng to local laws and regulatons. 2.2. Mounting Bracket to the Indicator Algn the mountng bracket over the threaded holes n the sde of the ndcator and nstall the knobs. Adjust the ndcator to the desred angle and tghten the knobs.

  • Page 13: Scale Base To The NdCator

    3000 Series Indicators EN- Remove the four hex head screws from the rear housng. Open the housng by carefully pullng the top of the front housng forward. Once all connectons are made, reattach the front housng. The screws should be tghtened fully to mantan a watertght seal. 2.3.2 Scale Base to the Indicator Pass the load cell cable through the stran relef (Fgure 1-1, tem 10) and attach t to termnal block J5 (Fgure 1-2, tem 5). Re-tghten the stran relef to ensure a watertght seal. Connection J5-1 +EXCITATION J5-2 +SENSE Jumper Connections J5-3 +SIGNAL For a 4-wre load cell wth no sense wres: Jumpers W1 and W2 must be shorted. J5-4 For a 6-wre load cell that ncludes sense wres, see Fgure 2-2. Jumpers W1 and W2 must J5-5 -SIGNAL be opened. J5-6 -SENSE For load cells wth an extra ground sheld wre: Connect the sheld to the center poston (GND) J5-7 -EXCITATION of J5. Fgure 2-2. Jumper Connectons. After wrng s completed and jumpers are n place, replace the ndcator housng screws. Make sure the stran relef s properly tghtened.

  • Page 14: MountNg Bracket

    EN-2 3000 Series Indicators Mounting Bracket Attach the bracket to a wall or table usng fasteners (not suppled) that are approprate for the type of mountng surface. The bracket wll accommodate up to 6 mm (1/4”) dameter screws. Locate the mountng holes as shown n Fgure 2-3. Fgure 2-3. Mountng Bracket Dmensons.

  • Page 15: Settings

    3000 Series Indicators EN-3 SETTINGS Menu Structure TABLE 3-. MENU STRUCTURE. CALIBRATION  SETUP  READOUT  MODE  UNIT  PRINT  MENU LOCK  END  SPAN  RESET  RESET  RESET  RESET  RESET  RESET  LINEARITY  NO  NO  NO  NO  NO  NO  YES  YES  GEO...

  • Page 16: Menu NavGatOn

    EN- 3000 Series Indicators Menu Navigation TO ENTER THE MENU MODE Press and hold the Menu button untl MENU appears on the dsplay. The frst upper level menu appears on the dsplay. Summary of button navgaton functons n menu mode: --Yes Allows entry nto the dsplayed menu. - Accepts the dsplayed settng and advances to the next menu tem. --No Skps by the dsplayed menu. - Rejects the dsplayed settng or menu tem and advances to the next avalable tem. --Back Moves backwards through the upper and mddle level menus. - Backs out of a lst of selectable tems to the prevous mddle level menu. --Exit Exts from menu drectly to the actve weghng mode. Calibration Menu Two calbraton processes are avalable: Span Calbraton and Lnearty Span Perform Calbraton. Lnearty Perform Geographc NOTES: Adjustment Set 00…Set … Set 31 1. Make sure that approprate calbraton masses are avalable before End Calbraton Ext CALIBRATE menu begnnng calbraton.

  • Page 17: Span CalBratOn

    3000 Series Indicators EN- 3.3. Span Calibration Span Calbraton uses two ponts to adjust the scale. The frst pont s the zero value where there s no weght on the scale. The second pont s the Span value where a calbraton mass s placed on the scale. When SPAN s dsplayed, press the Yes button to access the Span Calbraton menu tem. The dsplay flashes 0. Wth no weght on the scale, press the Yes button to establsh the zero pont. The dsplay shows --C-- whle the zero pont s establshed. The dsplay flashes the span calbraton pont. Place the specfed weght on the scale and press the Yes button. To choose a dfferent span pont, repeatedly press the No button to ncrement the selectons or press the Back button to decrement the selectons. Refer to Table 3-3 for avalable span ponts. When the desred value s dsplayed, place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the span pont s establshed. If span calbraton was successful, the scale exts to the actve weghng mode and dsplays the actual weght value.  3.3.2 Linearity Calibration Lnearty calbraton uses 3 calbraton ponts. The frst calbraton pont s establshed wth no weght on the scale. The second calbraton pont s establshed at approxmately half capacty. The thrd calbraton pont s establshed at capacty. The Lnearty calbraton ponts are fxed and cannot be altered by the user durng the calbraton procedure. Refer to Table 3-3 for the lnearty ponts. When LINEAr s dsplayed, press the Yes button to access the Lnearty Calbraton menu tem. The dsplay flashes 0. Wth no weght on the scale, press the Yes button to establsh the zero pont. The dsplay shows --C-- whle the zero pont s establshed. The dsplay flashes the md calbraton pont. Place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the md pont s establshed. The dsplay flashes the full calbraton pont. Place the specfed weght on the scale and press the Yes button. The dsplay shows --C-- whle the full pont s establshed.

  • Page 18: GeographCal Adjustment Factor

    EN- 3000 Series Indicators 3.3.3 Geographical Adjustment Factor The Geographcal Adjustment Factor (GEO) s used to compensate for varatons n gravty. Note: Changng the GEO Factor alters the calbraton. The GEO value was set at the factory and should only be changed by an authorzed manufacturer’s representatve or certfed verrcaton personnel. Refer to table 3-2 to determne the GEO factor that corresponds to your locaton. 3.3. End Calibration Advance to the next menu.
  • Page 19 3000 Series Indicators EN- TABLE 3-2. GEOGRAPHICAL ADJUSTMENT VALUES Elevaton n meters 1300 1625 1950 2275 2600 2925 3250 1300 1625 1950 2275 2600 2925 3250 3575 Elevaton n feet 1060 2130 3200 4260 5330 6400 7460 8530 9600 10660 1060 2130 3200 4260 5330 6400 7460...

  • Page 20: Setup Menu

    EN- 3000 Series Indicators Setup Menu When the Indcator s used for the frst tme, enter ths Reset No, Yes menu to set the Capacty and Graduaton. Legal for Trade Off, On Cal Unt kg, lb Capacty …20000 Graduaton 0.00…20 Power On Unt g, kg, lb, oz, lb:oz, Auto Zero Range 0%, 2%, 100%...
  • Page 21 3000 Series Indicators EN- TABLE 3-3. SETUP AND CALIBRATION VALUES Capacity Graduation size Graduation size with LFT ON Span calibration points Linearity with LFT OFF calibration points 0.0005, 0.001, 0.002, 0.001, 0.002, 0.005 2, 5 0.005 0.0005, 0.001, 0.002, 0.002, 0.005, 0.01 5, 10 5, 10 0.005, 0.01 0.001, 0.002, 0.005, 0.01 0.005, 0.01 5, 10, 15 5, 15 0.001, 0.002, 0.005, 0.01, 0.005, 0.01, 0.02 5, 10, 15, 20...

  • Page 22: GraduatOn

    EN-20 3000 Series Indicators 3.. Graduation Set the scale readablty. 0.001, 0.002, 0.005, 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20. NOTE: Not all settngs are avalable for each capacty. Refer to the Setup Table 3.3 for avalable settngs. • • • 3.. Power On Unit Set the unt that wll be actve at power on. oz, lb, g, kg, lb:oz or Auto (last unt n use when power was turned off.) 3.. Zero Range Set the percentage of scale capacty that may be zeroed. 0% = zerong dsabled 2% = zero up to 2 percent of capacty 100% = zero up to full capacty 3.. End Setup Advance to the next menu. Readout Menu Enter ths menu to customze dsplay functonalty. Reset: No, Yes Flter Level Lo, Med, H Auto Zero Trackng Off, 0.d, 1d, 3d Backlght Off, On, Auto...

  • Page 23: Auto-Zero TrackNg

    3000 Series Indicators EN-2 3..2 Filter Set the amount of sgnal flterng. LO = less stablty, faster stablzaton tme (<1 sec.) MEd = normal stablty, stablzaton tme (<2 sec.) HI = greater stablty, slower stablzaton tme (<3 sec.) 3..3 Auto-Zero Tracking Set the automatc zero trackng functonalty. OFF = dsabled. 0.5 d = the dsplay wll mantan zero untl a drft of 0.5 dvsons per second has been exceeded. 1 d = the dsplay wll mantan zero untl a drft of 1 dvson per second has been exceeded.

  • Page 24: Mode Menu

    EN-22 3000 Series Indicators Mode Menu Enter ths menu to actvate the desred applcaton Reset: No, Yes modes. Count: Off, On End Mode Ext MODE menu 3.. Reset Set the Mode menu to the factory defaults. No = not reset. Yes = reset. NOTE: If the Legal for trade menu tem s set ON, the settngs are not reset. 3..2 Parts Counting Mode Set the status.

  • Page 25: Reset

    3000 Series Indicators EN-23 Unit Menu Enter ths menu to actvate the desred unts. Default settngs are bold. Reset: No, Yes Klograms: Off, On Pounds: Off, On Grams: Off, On Ounces: Off, On Pounds:Ounces Off, On End Unt Ext UNIT menu 3.. Reset...

  • Page 26: End UnT

    EN-2 3000 Series Indicators 3.. End Unit Advance to the next menu. Print Menu Enter ths menu to defne prntng parameters. Default settngs are bold. Reset No, Yes Baud Rate: 300, 600, 1200, 2400, 4800, 00, 19200 Party: 7 Even, 7 Odd, 7 None,  None 3.. Reset Stop Bt  or 2 Set the Prnt menu to factory defaults. Handshake: Off, XON/XOFF NO = not reset.

  • Page 27: Stop BT

    3000 Series Indicators EN-2 3.. Stop Bit Set the number of stop bts. 1 = 1 stop bt. 2 = 2 stop bts. 3.. Handshake Set the flow control method. NONE = no handshakng. ON-OFF = XON/XOFF software handshakng. 3.. Print Stable Data Only Set the prnt crtera. OFF = values are prnted mmedately. ON = values are only prnted when the stablty crtera are met. 3.. Auto Print Set the automatc prntng functonalty.

  • Page 28: Menu Lock Menu

    EN-2 3000 Series Indicators Menu Lock Menu Enter ths menu. Default settngs are bold. Reset: No, Yes Lock Calbraton Menu Off, On Lock Setup Menu Off, On Lock Readout Menu Off, On Lock Mode Menu Off, On Lock Unt Menu Off, On Lock Prnt Menu Off, On End Lock Menu 3.. Reset...

  • Page 29: Lock PrNt

    3000 Series Indicators EN-2 3.. Lock Print Set the status. OFF = Prnt menu s not locked. ON = Prnt menu s locked. 3.. End Lock Advance to the next menu. 3.0 Security Switch A securty swtch s located on the Man PCB board. When the swtch s set to the on poston, user menu settngs that were locked n the Menu Lock can not be changed. Open the housng as explaned n Secton 2.3.1. Set the poston of securty swtch to ON as shown n Fgure 1-3. OPERATION Turning Indicator On/Off To turn the Indcator on, press the and hold the ON/ZERO Off button for 2 seconds. The Indcator performs a dsplay test, momentarly dsplays the software verson, and then enters the actve weghng mode. To turn the Indcator off, press and hold the ON/ZERO Off button untl OFF s dsplayed. Zero Operation Zero can be set under the followng condtons: • Automatcally at Power On (ntal zero).

  • Page 30: ChangNg UnTs Of Measure

    EN-2 3000 Series Indicators Changing Units of Measure Press and hold the PRINT Units button untl the desred measurng unt appears. Only measurng unts enabled n the Unt Menu wll be dsplayed (refer to Secton 3.7). Printing Data Prntng the dsplayed data to a prnter or sendng the data to a computer requres that the communcaton parameters n the Prnt Menu are set (refer to Secton 3.8). Press the PRINT Units button to send the dsplayed data to the communcaton port (the Auto-Prnt Mode n Secton 3.8 functon must be Off). Application Modes Only modes enabled n the mode menu wll be dsplayed (refer to Secton 3-6). .. Weighing Place the tem to be weghed on the scale. The llustraton ndcates a sample of 1.5 kg, Gross weght. Note: To return to the Weghng mode from the Parts Countng mode, press and hold the Mode button untl WEIGH s dsplayed. ..2 Parts Counting Use ths mode to count parts of unform weght. The Indcator determnes the quantty based on the average weght of a sngle part. All parts must be unform n weght for accurate measurements. To enter the Parts Countng mode, press and hold the Mode button untl Count s dsplayed. Average Piece Weight (APW) When the Mode button s released, CLr.PW Pcs s dsplayed.
  • Page 31 3000 Series Indicators EN-2 Recalling a Stored APW Press the No button to recall the exstng APW. Press the FUNCTION Mode button to temporarly dsplay the APW value. Establishing the Average Piece Weight (APW) The dsplay shows Put10 Pcs. Establishing a New APW Press the No button to ncrement the sample sze. Choces are 5, 10, 20, 50, 100 and 200. To establsh the APW, place the specfed quantty of samples on the scale and press the Yes button to capture the weght. Begin Counting Place the parts on the scale and read the count. If a contaner s used, be sure to tare the empty contaner frst.

  • Page 32: Serial Communication

    EN-30 3000 Series Indicators SERIAL COMMUNICATION The Indcator nclude an RS232 seral communcaton nterface. The setup of RS232 operatng parameters are more fully explaned n Secton 3.8. The physcal hardware connecton s explaned n n Secton 2.2. The nterface enables dsplay data to be sent to a computer or prnter. A computer can be used to control some functons of the ndcator usng the commands lsted n Table 5-1. Interface Commands Communcate to the ndcator usng the command characters lsted n Table 5-1. TABLE -. SERIAL INTERFACE COMMAND TABLE. Command Function Character Immedate Prnt of dsplayed weght (stable or unstable). Prnt stable dsplayed weght (accordng to stablty settng). Contnuous Prnt. Prnt when stable. Interval Prnt x = Prnt Interval (1-3600 sec) Same as pressng Zero button Same as pressng Tare button Download Tare value n grams (postve values only). Sendng 0T clears tare (f allowed) Prnt current unt: g, kg, lb, oz, lb:oz Set scale to unt x: 1=g, 2=kg, 3=lb, 4=oz, 5=lb:oz Verson: prnt name, software revson and LFT ON (f LFT s set ON). Esc R Global reset to reset all menu settngs to the orgnal factory defaults NOTES: • Commands sent to the Indcator must be termnated wth a carrage return (CR) or carrage return-lne feed (CRLF). • Data output by the Indcator s always termnated wth a carrage return-lne feed (CRLF). • The xT (preset tare) command s not avalable when LFT s set to ON.

  • Page 33: Output Format

    3000 Series Indicators EN-3 Output Format The default seral output format s shown below. Field: Polarity Space Weight Space Unit Stability Legend Length: Defntons: Polarty, “-” sgn f negatve, blank f postve. Weght, up to 6 numbers and 1 decmal, rght justfed, leadng zero blankng. Unts, up to 5 characters. Stablty, “?” character s prnted f not stable, blank f stable. Legend, up to 3 characters: G = gross weght, NET = net weght, T = tare...

  • Page 34: Legal For Trade

    EN-32 3000 Series Indicators LEGAL FOR TRADE When the ndcator s used n trade or a legally controlled applcaton t must be set up, verfed and sealed n accordance wth local weghts and measures regulatons. It s the responsblty of the purchaser to ensure that all pertnent legal requrements are met. Settings Before verfcaton and sealng, perform the followng steps: 1. Verfy that the menu settngs meet the local weghts and measures regulatons. 2. Perform a calbraton. 3. Set Legal for Trade to ON n the Setup menu. 4. Ext the menu. 5. Dsconnect power from the ndcator and open the housng as explaned n Secton 2.3.1. 6. Set the poston of the securty swtch to ON as shown n Secton 1.2, Fgure 1-2, Item 8. 7. Close the housng. 8. Reconnect power and turn the ndcator on. NOTE: For nstallatons that employ the audt tral sealng method, steps 5 to 8 are not requred. However, the securty swtch may be set to ON to safeguard aganst unntentonal changes to confguraton and calbraton settngs. NOTE: When Legal for Trade s set to ON and the securty swtch s set to ON, the followng menu settngs cannot be changed: Span Calbraton, Lnearty Calbraton, GEO, LFT, Calbraton Unt, Capacty, Graduaton, Power On Unt, Zero Range, Auto Zero Trackng, Expanded Mode, Count Mode, Klogram Unt, Pound Unt, Gram Unt, Ounce Unt, Pound Ounce Unt, Stable Only. To enable edtng of these menu settngs, return the securty swtch to the off poston and set LFT menu tem to off. Verification The local weghts and measures offcal or authorzed servce agent must perform the verfcaton procedure. Please contact your local weghts and measures offce for further detals. Sealing .3. Physical Seals For jursdctons that use the physcal sealng method, the local weghts and measures offcal or authorzed servce agent must apply a securty seal to prevent tamperng wth the settngs. Refer to the llustratons below for sealng methods.
  • Page 35 3000 Series Indicators EN-33 Seal SEAL Fgure 6-1. Wre Seal Fgure 6-2. Paper Seal .3.2 Audit Trail Seal For jursdctons that use the audt tral sealng method, the local weghts and measures offcal or authorzed servce agent must record the current confguraton and calbraton event counter values at the tme of sealng. These values wll be compared to values found durng a future nspecton. NOTE: A change to an event counter value s equvalent to breakng a physcal seal. The audt tral uses two event counters to record changes to confguraton and calbraton settngs. • The confguraton event counter (CFG) wll ndex by 1 when extng the menu f one or more of the followng settngs are changed Legal for Trade, Calbraton Unt, Capacty, Graduaton, Power On Unt, Zero Range, Auto Zero Trackng, Expanded Mode, Count Mode, Klogram Unt, Pound Unt, Gram Unt, Ounce Unt, Pound Ounce Unt, Stable Only. Note that the counter only ndexes once, even f several settngs are changed. The confguraton event counter values range from CFG000 to CFG999. When the value reaches CFG999, the count starts over at CFG000. • The calbraton event counter (CAL) wll ndex by 1 when extng the menu f a Span Calbraton, Lnearty Calbraton or GEO settng change s made. Note that the counter only ndexes once, even f several settngs are changed. The calbraton event counter values range from CAL000 to CAL999. When the value reaches CAL999, the count starts over at CAL000. The event counters can be vewed by pressng and holdng the MENU button. Whle the button s held, the dsplay wll show MENU followed by Audt. CALIBRATION MODE Release the button when Audt s dsplayed to vew the audt tral nformaton. CALIBRATION MODE...
  • Page 36 EN-3 3000 Series Indicators The audt tral nformaton s dsplayed n the format CFGxxx and CALxxx. CALIBRATION MODE CALIBRATION MODE Then the ndcator returns to normal operaton. CALIBRATION MODE...

  • Page 37: SettNgs

    Remove load on Scale. turned on. Load on Scale s not stable. Wat for load to become stable. Load Cell damage. Servce requred. Unable to calbrate. Lock Calbraton Menu set to On. Set Lock Calbraton Menu to Off. Refer to Secton 3.9 Menu Lock. Lock swtch s “on”. Set the Lock swtch to Off. LFT menu set to On. Set LFT menu to Off. Incorrect value for calbraton mass. Use correct calbraton mass. Cannot dsplay weght n desred weghng Unt not set to On. Enable unt n the Unts Menu. unt. Refer to Secton 3.7 n the Unt Menu. Cannot change menu settngs. Menu has been locked. Set selected menu to Off n the Lock Menu. Lock Swtch on the crcut board may need to be set to the Off poston. Lock swtch set on. Set the Lock swtch to off. Battery ndcator s flashng. Battery dscharged. Connect ndcator to power and charge battery. Battery fals to charge fully. Battery s defectve. Have the battery replaced by an authorzed Ohaus servce dealer. Error 7.0 Unstable weght readng when defnng Unstable Error, check platform locaton. reference weght.

  • Page 38: TroubleshootNg

    Remove load from scale. Recalbrate scale. Error 8.2 Weght readng below Power On Zero lmt. Add load to scale. Recalbrate scale. Error 8.3 Weght readng exceeds Overload lmt. Reduce load on scale. Error 8.4 Weght readng below Underload lmt. Add load to scale. Recalbrate scale. Err 9.0 Internal fault Servce requred. Err 9.5 Calbraton data not present. Calbrate scale. Err 53 EEPROM data ncorrect. Servce requred. CAL E Calbraton Error. Calbraton value outsde Repeat calbraton usng correct calbraton allowable lmts. weghts. LOW.rEF The average pece weght of the parts s small Use parts wth average pece weght greater (warnng). than or equal to 1 dvson. REF.WT Err The average pece weght of the parts s too Use parts wth a average pece weght small. greater than or equal to 0.1 dvson. Service Information If the troubleshootng secton does not resolve your problem, contact an authorzed Ohaus Servce Agent. For Servce assstance n the Unted States, call toll-free 1-800-526-0659 between 8:00 AM and 5:00 PM Eastern Standard Tme. An Ohaus Product Servce Specalst wll be avalable to assst you. Outsde the USA, please vst our webste www.ohaus.com to locate the Ohaus offce nearest you.

  • Page 39: Technical Data

    3000 Series Indicators EN-3 TECHNICAL DATA Specifications Materials Housng: stanless steel Keypad: polyester Dsplay Wndow: polycarbonate Ambient conditions The techncal data s vald under the followng ambent condtons: Ambent temperature: -10°C to 40°C / 14°F to104°F Relatve humdty: Maxmum relatve humdty 80% for temperatures up to 31°C decreasng lnearly to 50% relatve humdty at 40°C. Alttude: up to 2000m Operablty s assured at ambent temperatures between -10°C. and 40°C.
  • Page 40 EN-3 3000 Series Indicators Accessories TABLE -2. ACCESSORIES. DESCRIPTION PART NUMBER Column Mount Kt, 35 cm panted steel 80251743 Column Mount Kt, 70 cm panted steel 80251744 Column Mount Kt, 35 cm stanless steel 80251745 Column Mount Kt, 70 cm stanless steel 80251746 Interface Cable/PC 9-pn 80500552 Interface Cable/PC 25-pn 80500553...
  • Page 41 3000 Series Indicators EN-3 Drawings and Dimensions 239 mm 9 in 71 mm 212 mm 2.8 in 8.3 in 149mm 5.8 in 201 mm 8.1 in Fgure 8-1. Indcator Overall Dmensons wth Mountng Bracket.

  • Page 42: ComplAnce

    EN-0 3000 Series Indicators Compliance Compliance Complance to the followng standards s ndcated by the correspondng mark on the product. Marking Standard Ths product conforms to the EMC drectve 2004/108/EC, the Low Voltage Drectve 2006/95/EC and the Non-automatc Weghng Instruments Drectve 90/384/EEC. The complete Declaraton of Conformty s avalable from Ohaus Corporaton. AS/NZS4251.1 Emsson, AS/NZS4252.1 Immunty UL60950-1: 2003 EC Emissions Note Ths devce comples wth EN55011/CISPR 11 Class B Group 1. Important notice for verified weighing instruments Weghng Instruments verfed at the place of manufacture bear one of the precedng mark on the packng label and the green ‘M’ (metrology) stcker on the descrptve plate. They may be put nto servce mmedately. Weghng Instruments to be verfed n two stages have no green ‘M’ (metrology) on the descrptve plate and bear one of the precedng dentfcaton mark on the packng label. The second stage of the ntal verfcaton must be carred out by the approved servce organzaton of the authorzed representatve wthn the EC or by the natonal weght & measures (W+M) authortes. The frst stage of the ntal verfcaton has been carred out at the manufacturers work. It comprses all tests accordng to the adopted European standard EN 45501:1992, paragraph 8.2.2. If natonal regulatons lmt the valdty perod of the verfcaton, the user of the weghng nstrument must strctly observe the re-verfcaton perod and nform the respectve W+M authortes.
  • Page 43 3000 Series Indicators EN- Disposal In conformance wth the European Drectve 2002/96/EC on Waste Electrcal and Electronc Equpment (WEEE) ths devce may not be dsposed of n domestc waste. Ths also apples to countres outsde the EU, per ther specfc requrements. Please dspose of ths product n accordance wth local regulatons at the collectng pont specfed for electrcal and electronc equpment. If you have any questons, please contact the responsble authorty or the dstrbutor from whch you purchased ths devce. Should ths devce be passed on to other partes (for prvate or professonal use), the content of ths regulaton must also be related. Thank you for your contrbuton to envronmental protecton. For dsposal nstructons n Europe, refer to www.ohaus.com/weee. FCC Note Ths equpment has been tested and found to comply wth the lmts for a Class A dgtal devce, pursuant to Part 15 of the FCC Rules. These lmts are desgned to provde reasonable protecton aganst harmful nterference when the equpment s operated n a commercal envronment. Ths equpment generates, uses, and can radate rado frequency energy and, f not nstalled and used n accordance wth the nstructon manual, may cause harmful nterference to rado communcatons. Operaton of ths equpment n a resdental area s lkely to cause harmful nterference n whch case the user wll be requred to correct the nterference at hs own expense. Industry Canada Note Ths Class A dgtal apparatus comples wth Canadan ICES-003. Cet apparel numérque de la classe A est conforme à la norme NMB-003 du Canada. ISO 00 Registration In 1994, Ohaus Corporaton, USA, was awarded a certfcate of regstraton to ISO 9001 by Bureau Vertus Qualty Internatonal (BVQI), confrmng that the Ohaus qualty management system s complant wth the ISO 9001 standard’s requrements. On May 15, 2003, Ohaus Corporaton, USA, was re-regstered to the ISO 9001:2000 standard.
  • Page 44 LIMITED WARRANTY Ohaus products are warranted aganst defects n materals and workmanshp from the date of delvery through the duraton of the warranty perod. Durng the warranty perod Ohaus wll repar, or, at ts opton, replace any component(s) that proves to be defectve at no charge, provded that the product s returned, freght prepad, to Ohaus. Ths warranty does not apply f the product has been damaged by accdent or msuse, exposed to radoactve or corrosve materals, has foregn materal penetratng to the nsde of the product, or as a result of servce or modfcaton by other than Ohaus. In leu of a properly returned warranty regstraton card, the warranty perod shall begn on the date of shpment to the authorzed dealer. No other express or mpled warranty s gven by Ohaus Corporaton. Ohaus Corporaton shall not be lable for any consequental damages. As warranty legslaton dffers from state to state and country to country, please contact Ohaus or your local Ohaus dealer for further detals.
  • Page 48 Ohaus Corporaton 19A Chapn Road P.O. Box 2033 Pne Brook, NJ 07058, USA Tel: (973) 377-9000 Fax: (973) 593-0359 www.ohaus.com *80252869* P/N 80252869 © 2009 Ohaus Corporaton, all rghts reserved. Prnted n Chna...

Table of Contents