Omega PHCN-37 Quick Start Up Manual

5
To Configure Temperature (If You
Selected MANU for Temperature
Compensation):
1. Press MENU until the controller
displays.
SETPTS /pH
2. Press T/mV. The controller
displays the actual constant
temperature.
SETPTS /pH
3. Press /pH to change the value
of the flashing digit.
4. Press T/mV to advance to the next digit.
5. Repeat steps 3 and 4 until the controller displays
the desired value.
6. Press MENU to select the value shown. The
unit displays.
SETPTS /pH T/mV MENU RESET SETPTS /pH T/mV MENU RESET
Press MENU until the controller displays c c a a l l . . 2 2
7.
or c c a a l l . . 3 3 .
To Perform Calibration
(2-Point Example:)
1. Place your electrode into a pH 7
buffer solution.
2. Press T/mV. The controller
SETPTS /pH
displays:
3. Press T/mV. The controller
displays the previous value of IN 1.
SETPTS /pH
4. Press T/mV again. The
controller displays the buffer
solution's pH value. Allow enough
time for the electrode to settle.
6
5. Press MENU until the controller displays.
SETPTS /pH T/mV MENU RESET SETPTS
T/mV MENU RESET
indicating that the value is stored.
6. Rinse the electrode with distilled water and place
it into a pH4 or pH10 solution.
7. Press T/mV. The controller displays the
T/mV MENU RESET
previous value of IN 2.
8. Press T/mV again. The controller displays the
buffer solution's pH value. Allow enough time for
the electrode to settle.
9. Press MENU. The controller displays:
SETPTS /pH T/mV MENU RESET SETPTS /pH T/mV MENU RESET
indicating that the value is stored.
For a 3-point calibration, you follow the same
procedure used in 2-point calibration, except you
place the electrode into three buffer solutions in
this order: pH4, pH7, and then pH10.
10. Press RESET twice.
The controller displays:
and then the current pH
value.
Your controller is now up
and running.
T/mV MENU RESET
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.
This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.
WARNING: These products are not designed for use in, and should not be used
T/mV MENU RESET
for, patient connected applications.
The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.
TRADEMARK NOTICE: omega.com
,
trademarks of OMEGA Engineering, Inc.
are
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for a period of one (1) year from the date of
purchase. In addition to OMEGA's standard warranty period, OMEGA
Engineering will extend the warranty period for four (4) additional years if the
warranty card enclosed with each instrument is returned to OMEGA.
If the unit should malfunction, it must be returned to the factory for evaluation.
OMEGA's Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective it will be repaired or replaced at no
charge. Omega's WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
/pH T/mV MENU RESET
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of being damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGA's control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental
or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a "Basic Component" under 10 CFR 21 (NRC), used in
or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any
SETPTS /pH T/mV MENU RESET
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY
/ DISCLAIMER language, and additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising
out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the
return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please
have the following information available
BEFORE
contacting OMEGA:
SETPTS /pH T/mV MENU RESET
1. P.O. number under which the
product was PURCHASED,
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA's policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2006 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of OMEGA ENGINEERING, INC.
PATENT NOTICE: The "Meter Case Bezel Design" is a trademark of
NEWPORT Electronics, Inc., registered in the U.S. USED UNDER LICENSE.
This product is covered by one or more of the following patents: U.S. Pat. No.
Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2.
OTHER INTERNATIONAL PATENTS PENDING.
™ ®
, and ,
MQS1570/1206
PHCN-37
MICROPROCESSOR-BASED
pH CONTROLLER
OMEGAnet
www.omega.com
USA:
ISO 9001 Certified
Canada:
For immediate technical or application assistance:
USA and Canada:
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following information
available BEFORE contacting OMEGA:
Mexico and
Latin American:
1. P.O. number to cover the COST of
the repair,
2. Model and serial number of product,
and
3. Repair instructions and/or specific
Benelux:
problems relative to the product.
Czech Republic:
France:
Germany/Austria:
United Kingdom:
ISO 9001 Certified
12700ML-99 Rev. D
MADE IN
USA
®
®
® On-Line Service Internet e-mail
info@omega.com
Servicing North America:
One Omega Drive, P.O. Box 4047
Stamford CT 06907-0047
TEL: (203) 359-1660 FAX: (203) 359-7700
e-mail: info@omega.com
976 Bergar
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928 FAX: (514) 856-6886
e-mail: info@omega.ca
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA ®
Customer Service: 1-800-622-2378 / 1-800-622-BEST ®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN ®
TEL: (001) 203-359-7803 FAX: (001) 203-359-7807
e-mail: espanol@omega.com
Servicing Europe:
TEL: +31 20 3472121 FAX: +31 20 6434643
Toll Free in Benelux: 0800 0993344
e-mail: sales@omegaeng.nl
Frystatska 184, 733 01 Karviná
TEL: +420 59 6311899 FAX: +420 59 6311114
e-mail: info@omegashop.cz
TEL: +33 1 61 37 29 00 FAX: +33 1 30 57 54 27
Toll Free in France: 0800 466 342
e-mail: sales@omega.fr
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0 F AX: +49 7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: info@omega.de
One Omega Drive
River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: +44 161 777 6611 FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: sales@omega.co.uk