Work Sharp Combo User Manual

COMBO
SCAN FOR DEMO
KNIFE SHARPENER
USER GUIDE
1
4
3
SHARPENING GUIDES
1
Angle guides create a consistent bevel across the entire
blade.
HONING GUIDES
2
Angle guides make honing and re-sharpening easy and
repeatable.
GRIP
3
Textured side grip helps you stabilize while sharpening.
SWITCH
4
One sharpening mode. Same result everytime.
WORKSHARPTOOLS.COM/HOW-TO-VIDEOS

Important SafeGuards

WARNING!
You will be creating incredibly sharp knives and tools with this
sharpener. Please handle them with care. Use caution to avoid cutting yourself.
WARNING!
READ all safety warnings and all instructions. When using electrical
appliances, basic safety precautions should always be followed. Every user should
read these instructions.
For Household Use Only
Close supervision is necessary when any appliance is used by or near children.
2
Children shall not play with appliance.
Do not let the power cord hang over edge of table or counter.
The power cord plug must match the outlet. This appliance has a polarized plug (one
blade is wider than the other). To reduce the risk of electric shock, this plug will fit in
a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in
any way.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
appliance. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
Carefully route the power cord to avoid damage from the knife blades while
sharpening.
The ON and OFF positions of the appliance Power Switch are designated by the
following I and O symbols:
Where I = ON and O = OFF
Do not use appliance with a damaged cord or plug or after the appliance
malfunctions or is dropped or damaged in any manner. Return appliance to the
nearest qualified service center for examination, repair or electrical or mechanical
adjustment. (Type Y attachment).
Stay alert. This appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
To protect against electrical hazards, do not immerse in water or other liquid. Do not
expose to rain or wet conditions.
Avoid contact with moving parts.
Only use replacement parts or attachments recommended or sold by the
manufacturer. Use of unauthorized parts may cause fire, electric shock or injury.
Only insert clean knife blades into the appliance. Do not attempt to sharpen scissors,
axes or other tools, or any blade that does fit properly into the sharpening slots.
Do not use oils, water or any other lubricant with appliance.
Do not operate appliance if the switch does not turn it on and off.
Do not use outdoors.
WARNING!
This product contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some dust created by
power sanding, sawing, grinding, drilling and other such activities contains
chemicals or particulates harmful to humans. Your risk from these exposures varies,
depending on how often you do this type of work. To reduce your exposure to
these chemicals, work in a well ventilated area, and work with approved safety
equipment, such as dust masks that are specifically designed to filter out airborne
microscopic debris.
The appliance label may include the following symbols:
V ........................................Volt A ......................amperes
Hz .....................................Hertz W .....................watts
min ...................................minutes .................alternating current
n o ....................no load speed
...............................direct current
..................................Class II Construction ..................earthing terminal
......................................safety alert symbol rpm .................revolutions or
................................................. reciprocations per minute
Service: Please contact Darex Customer Support:
Darex, LLC
Internet: www.worksharptools.com Tel: 1 (800) 597-6170
210 E. Hersey St. Fax: 1 (541) 552-1377
Ashland, OR 97520 E-Mail: info@darex.com
SAVE THESE INSTRUCTIONS
- Original Instructions -
2
Thank you for purchasing this tool!
Your support makes a real impact on our small business.
We are confident you will be very pleased with your purchase.
If that is not the case, please contact us.
We know you work hard for your money and we want to provide you with
a high performance, high value tool.
Please keep in touch and let us know how we're doing.
Until then, stay sharp out there...
- Team Work Sharp, Ashland Oregon

Getting Started

Setting up your sharpener
• Your sharpener is ready to use right out of the box, just plug it in and turn it on.
Anatomy of a Knife:
Blade Handle
Tip Spine
Finger Guard
Edge Heel
3 4