Advertisement
Advertisement
Table of Contents
Related Manuals for Cervélo R3 Rim
Summary of Contents for Cervélo R3 Rim
- Page 1 R3 RIM MANUAL | EN Version 1 I 07.02.2017...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction ......................1 Frame Features ....................2 Fork Preparation ....................3 Small Parts .......................5 Frame Preparation ....................6 Mechanical Cable Routing ................7 Electric Cable Routing ..................9 Seatpost Assembly & Installation ..............11 Frame Protection Installation................13 Tire Clearance ....................14 INTRODUCTION Welcome to the Cervélo family, and congratulations on your decision to ride an R Series bicycle. The ultra-lightweight engineering of your Cervélo R Series classic road bike will help you attack any climbs, and enjoy speed and control on descents. -
Page 3: Frame Features
FRAME FEATURES A guide to your Cervélo R3 frame. Front derailleur wire exit hole, electric and mechanical Down tube internal cable ports Rear dropout cable exit Bottom bracket cable port... -
Page 4: Fork Preparation
FORK PREPARATION A. Stem Cap + 5mm bolt 1. Apply grease to the bearing seats, and Install the upper & lower headset bearings into the head tube. B. Headset Spacers 2. Fit the fork provided with your frame into the head tube with the C. - Page 5 5. To trim fork steerer, use only a saw suitable for cutting carbon, and a cutting guide. 6. Carefully sand a bevel to the inside of the cut end of the steerer tube to fit the insert. 7. Dry fit insert to check that it is flush with the cut end of the steerer Insert should be flush tube.
-
Page 6: Small Parts
SMALL PARTS Designed to accommodate electronic, mechanical and hydraulic controls, the R3 frame is engineered to provide seamless integration of all shifting systems, regardless of method or brand. In order to do so, you will require the parts shown below*: Mechanical Brake &... -
Page 7: Frame Preparation
FRAME PREPARATION With the wheel installed in the frame, use a Derailleur Alignment Gauge to ensure the hanger is aligned parallel to the wheel. Apply Loctite 242 to the fixing screws, and tighten the screws equally to a maximum of 1 Nm. -
Page 8: Mechanical Cable Routing
MECHANICAL CABLE ROUTING It is recommended that front and rear derailleur cables be installed after the brake hose has been installed. These routing illustrations are intended as a supplement to the manufacturer’s installation instructions only. Please refer to the component manufacturer’s service center or website for further information. Install cable housing (with ferrules) into individual Mechanical Brake &... - Page 9 The front cable travels across the non-drive side slot, and in the Route gear cables out of the bottom direction of the seat tube. The rear cable travels along the drive bracket cable port. Ensure that the cables side slot, and along the chain stay. When complete, snap Bottom are not twisted together.
-
Page 10: Electric Cable Routing
ELECTRIC CABLE ROUTING It is recommended that electric cabling and junction points be installed after the brake hose has been installed. These routing illustrations are intended as a supplement to the manufacturer’s installation instructions only. Please refer to the component manufacturer’s service center or website for further information. Route Di2 wire to the bottom bracket through the Down Tube Di2 Wire Guide. - Page 11 Install the Rear Derailleur Wire Guide. For wireless systems install the Rear With all wires inside, cap the bottom bracket Derailleur Blanking Plug. access port with the Bottom Bracket Access Port Rubber Blanking Plug.
-
Page 12: Seatpost Assembly & Installation
SEATPOST ASSEMBLY & INSTALLATION 1. Apply a light coat of carbon assembly compound to the upper face of the Seatpost, making sure to cover area around the adjustment slots. 2. Locate saddle rail between upper and lower clamps, and place on Seatpost. - Page 13 Insert the assembled battery and holder into the seatpost. 1. Apply carbon assembly paste to the frame and mount the Seatpost Clamp. Press the Di2 battery into 2. Insert the seatpost into the frame, the R-Series Internal Battery and adjust height and alignment. Holder and attach the cable Torque the Seatpost Clamp bolt according to manufacturers...
-
Page 14: Frame Protection Installation
FRAME PROTECTION INSTALLATION Install the front derailleur using the bolt provided with the derailleur. Torque to the derailleur specifications. Clean the chain stay using isopropyl alcohol. Install the Chain Stay Guard by removing adhesive backing, and fixing the guard to the frame. The bottom rearward edge should be 12mm from the front edge of the Install chain catcher when installing the front... -
Page 15: Tire Clearance
TIRE CLEARANCE Your Cervélo bicycle complies with the ISO 4210-2:4.10.2 standard for tire clearance. In order to comply with these safety standards and maintain your Limited Lifetime Warranty, a minimum of 4mm of clearance must remain between the tire and any frame element. Due to the growing complexity of tire and rim interfaces, Cervélo recommends identifying the available space before choosing a tire. - Page 16 CERVÉLO EUROPE GMBH Siemensstraße 1-3 49661 Cloppenburg, Germany + 49 (4471) 95855-0 info@cervelo-europe.com www.cervelo-europe-dealer.com 1973K3418004...