MINI PARALLEL REMOVER Iron holder with a sleep mode Instruction Manual Thank you for purchasing the FM-2023 mini parallel remover. Please read this manual before operating the FM-2023. Please keep this manual readily accessible for reference. CAUTION • The FM-2023 cannot function by itself. It must be connected to the HAKKO FM-203 or FM-206 station.
1. PACKING LIST Mini parallel remover handpiece .... 1 Connecting cable ........1 Tips (T9-I) 2pcs/set ........ 1 Iron holder (with Cleaning sponge)..1 Heat resistant pad ........1 Component bed ........1 Mini parallel remover handpiece Tip (shape-I) Heat resistant pad Cleaning sponge Iron holder...
3. WARNINGS, CAUTIONS AND NOTES Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s attention to significant items. They are defined as follows: WARNING: Failure to comply with a WARNING may result in injury or death. CAUTION: Failure to comply with a CAUTION may result in injury to the operator, or damage to the items involved.
4. PART NAMES Button Handle Fixing flange Plug Cord Plug Connecting cable Cleaning sponge Heat resistant pad Component bed Iron holder 5. SETTING UP THE FM-2023 1. Connector cord NOTE: This product is protected against electrostatic Pass the connector cord through the hole discharge and must be grounded for full ef- in the heat resistant pad.
6. OPERATION l Controls and displays Refer to the HAKKO FM-203 or FM-206 instruction manual. NOTE: The HAKKO FM-203 has 2 channels; D and S channel. The MODEL FM-2023 can be connected to only the D channel. HAKKO FM-203 The HAKKO FM-206 has 3 channels: 1, 2 soldering station and 3 channel.
l Operating instructions 1. Set the Temperature CAUTION: NOTE: Never set the temperature to any value over Once the two tips are inserted into the hand- 400°C (750°F). Doing so may damage the piece, heat control begins. station. Set the temperature according to the Both tips of the set must be inserted or the type of work to be done.
Page 7
l Control card and changing the tempera- ture setting Please refer to the HAKKO FM-203 or FM-206 Instruction manual. l Replacing the tip Removing and inserting the tip: FM-2023 24V-140W Removing the tip: Hold the handle and pull the tip out of the Hold the handpiece at the front to remove tip.
7. MAINTENANCE l Tip maintenance Please refer to the HAKKO FM-203 or FM-206 Instruction manual. l Checking Procedure WARNING: Unless otherwise directed, carry out these procedures with the power switch OFF and the power UNPLUGGED. l Verify the electrical integrity of 1.
8. TROUBLESHOOTING GUIDE WARNING: Disconnect the power plug before servicing. Failure to do so may result in electric shock. l The tip does not heat up. CHECK : Is the tip inserted properly? ACTION : Insert the tip completely. • The sensor error is dis- CHECK : Is the connection cord and/or the...
Page 10
l The low-temperature CHECK : Is the tip too small for the items to be removed? alarm tolerance error ACTION : Use a tip with a large thermal occurs frequently. capacity. CHECK : Is the setting value for the low temperature alarm tolerance too low? ACTION : Increase the setting value.
9. PARTS LIST ●Mini parallel remover Item No. Part No. Part Name Specifications B2300 Heat resistant pad B2849 Component bed B3253 Connecting cable FM2023-02 Handpiece only w/o tip ●Iron holder Item No. Part No. Part Name Specifications FH200-04 Iron holder With cleaning sponge ●Iron holder parts Item No.
10. WIRING DIAGRAM P.W.B/LED LED1 Instruction manual in the language of Japanese, English, Chinse, French, German and Korean can be downloaded from the HAKKO Document Portal. (Please note that some languages may not be available depending on the product.) HEAD OFFICE 4-5, SHIOKUSA 2-CHOME, NANIWA-KU, OSAKA, 556-0024 JAPAN TEL:+81-6-6561-3225 FAX:+81-6-6561-8466 http://www.hakko.com...
Need help?
Do you have a question about the FM-2030 and is the answer not in the manual?
Questions and answers