Table of Contents
Advertisement
SYSTEM PROGRAMMING
Following are instructions for programming "Areas" of the
system memory. Only the Areas pertaining to the specific
installation need to be programmed. Reference the following
pages with the programming outline to program the system.
The unit must be in Program Mode to perform any system
p r o g r a m m i n g . F O L LO W T H E S TE P S IN TH E
PROGRAMMING OUTLINE TO PROGRAM THE SYSTEM.
NOTE: The following keypad functions pertain to the black
AM/II keypad inside the AE-1, not the chrome entry keypad
on the face of the AE-1 unit.
Entering Program Mode
STEP 1 Enter programming mode by pressing and holding
the [
] key for about five seconds. With computer
*
access press the ESC key.
STEP 2 Enter 123456 (if the system is new), or the correct
password and press [OK].
Exiting Program Mode
Exit Program Mode by pressing and holding the [
seconds. With computer access, press CTRL-Z.
NOTE: The system will automatically exit Program Mode
after five minutes of programming inactivity.
PROGRAMMING OUTLINE
The following outline is intended to guide you through the
programming of the system. The unit is programmed by setting
options in various program "Areas". Use this outline in
conjunction with the following program area detail pages to set
up the system.
1.
Enter program mode (Hold the [
ESC on programming computer).
2.
Program any single transmitters using Single Transmitters
Area 01.
3.
Program any block coded transmitters using Block Area 02.
4.
Program any keypad entry codes using Entry Code Area 05.
5.
Program any block card codes using Block Card Codes
Area 06.
6.
Program the telephone and directory numbers and names
using Telephone Entry Numbers Area 07.
4
] key for three
*
] key for 5 seconds or press
*
SINGLE TRANSMITTERS
Learn Single Xmtr(s)
Press OK when Ready
U P & D O W N
A R R O W S W I L L
Enter Single Xmtr Numb
Enter Xmtr. ID: 000
M O V E B E T W E E N
M E N U T O P I C S
Suspend Single Xmtr.
Transmitter ID: = [0000]
Reactivate Single Xmtr.
Transmitter ID: = [0000]
Status of Single Xmtr.
Transmitter ID: = [0000]
Enter Expiration Date.
Expires On: mm/dd/yyyy
[ O K ] K E Y E N T E R S
Delete One Single Xmtr.
Transmitter ID: = [0000]
N U M E R I C D A T A
I N T O M E M O R Y
Delete All Single Xmtr.
Are You Sure? Yes No
PROGRAM SINGLE
TRANSMITTERS
PROGRAM BLOCK CODED
TRANSMITTERS
PROGRAM KEYPAD
ENTRY CODES
PROGRAM BLOCK
PROGRAM TELEPHONE ENTRY
NUMBERS AND NAMES
TEST SYSTEM
AREA 01
L E F T & R I G H T
A R R O W S W I L L
1.1
1.1A
M O V E B E T W E E N
Select Validation Group.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
M E N U I T E M S
OK
1.2
1.1B
Learning Transmitters
Transmitter ID: = 0001
B L I N K I N G I T E M
1.3
I S T H E O N E
C U R R E N T L Y
1.4
S E L E C T E D
1.5
1.5A
Item/Code:
Press OK When Ready
1.6
1.7
[ O K ] K E Y E N T E R S
S E L E C T E D M E N U
[ O K ] K E Y S E L E C T S
1.8
I T E M
S U B - M E N U S
M E M O R Y
(AREA 01)
(AREA 02)
(AREA 05)
CARD CODES
(AREA 06)
(AREA 07)
I N T O
Advertisement
Table of Contents
