All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JA/CC 0964 BU TV Consumer Care, the Netherlands...
EN 2 LC8.2HA LA Revision List 1. Revision List Manual xxxx xxx xxxx.0 • First release. 2. Technical Specifications and Connections Index of this chapter: 2.1 Technical Specifications 2.2 Directions for Use 2.3 Connections 2.4 Chassis Overview Notes: • Figures can deviate due to the different set executions.
Page 3
Technical Specifications and Connections LC8.2HA LA EN 3 Connections HDMI 1 HDMI 2 HDMI 3 AUX AUDIO DIGITAL VOLUME OUT 1 CONTROL AUX AUDIO OUT 2 DATA 2 DATA 1 (RJ12) RS 232 AUDIO IN (RJ45) SMARTPLUG SPDIF OUT SERV. C...
Page 4
EN 4 LC8.2HA LA Technical Specifications and Connections 8 - S-Video (Hosiden): Video Y/C - In 13 - RJ12 DATA1 (HM-Link - In/Out) - Ground Y - LED-in_SCL < 0.3 V, active low - Ground C - IR-in_SDA < 0.3 V, active low / 75 Ω...
Spare Parts • Check the strain relief of the Mains/AC Power cord for proper function. For the latest spare part overview, consult your Philips Spare • Check the electrical DC resistance between the Mains/AC Part web portal. Power plug and the secondary side (only for sets that have a Mains/AC Power isolated power supply): 1.
Page 6
EN 6 LC8.2HA LA Precautions, Notes, and Abbreviation List 3.3.6 Alternative BOM identification Abbreviation List It should be noted that on the European Service website, 0/6/12 SCART switch control signal on A/V “Alternative BOM” is referred to as “Design variant”.
Page 7
Precautions, Notes, and Abbreviation List LC8.2HA LA EN 7 Digital Noise Reduction: noise uses 8 bit or 10 bit data words, and has reduction feature of the set a maximum data rate of 270 Mbit/s, DRAM Dynamic RAM with a minimum bandwidth of 135 Digital Rights Management MHz.
Page 8
System on Chip Sync On Green SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board STBY STand-BY SVGA...
Mechanical Instructions LC8.2HA LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal ME8 Styling •...
Page 10
EN 10 LC8.2HA LA Mechanical Instructions 18510_205_090407.eps 090407 Figure 4-2 Cable dressing 42-inch sets 2009-Apr-10...
Page 11
Mechanical Instructions LC8.2HA LA EN 11 Service Positions Assy/Panel Removal ME8 Styling For easy servicing of this set, there are a few possibilities 4.3.1 Rear Cover created: • The buffers from the packaging. Warning: • Foam bars (created for Service).
Page 12
EN 12 LC8.2HA LA Mechanical Instructions 4.3.4 IR & LED Board 4.3.6 Display Supply Panel Refer to next figure for details. Refer to next figure for details (is for 42” set, for other 1. Unplug connectors [1]. screensizes the process might slightly deviate): 2.
Page 13
Mechanical Instructions LC8.2HA LA EN 13 4.3.8 Small Signal Board (SSB) Refer to next figure for details. 4. The SSB can now be taken out of the set, together with the Caution: it is mandatory to remount all screws at their original front shield and the side cover.
Page 14
EN 14 LC8.2HA LA Mechanical Instructions 4.3.9 LCD Panel 5. Unplug the Speaker cables at the “rim contacts” [5]. 6. Remove the screws [6] that hold the complete subframe to the front cabinet. Refer to next figures for details. Note that this description is 7.
Service Modes, Error Codes, and Fault Finding LC8.2HA LA EN 15 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: Software Identification, Version, and Cluster 5.1 Test Points The software ID, version, and cluster will be shown in the main 5.2 Hotel mode...
Page 16
EN 16 LC8.2HA LA Service Modes, Error Codes, and Fault Finding 5.3.2 Service Default Mode (SDM) On Screen Menu After activating SDM, the following screen is visible, with SDM in the upper right corner of the screen to indicate that the Purpose television is in Service Default Mode.
Page 17
Service Modes, Error Codes, and Fault Finding LC8.2HA LA EN 17 5.3.3 Service Alignment Mode (SAM) Caution: When this mode is selected without ComPair connected, the TV will be blocked. Remove the AC power to reset the TV. Purpose 12. SW Events. Only to be used by development to monitor •...
Page 18
EN 18 LC8.2HA LA Service Modes, Error Codes, and Fault Finding 5.3.4 Customer Service Mode (CSM) Menu Explanation 1. MODEL. Type number, e.g. 32PFL7762D/05. (*) 2. PROD S/N. Product serial no., e.g. AG1A0712123456. (*) Purpose 3. SW ID. Software cluster and version is displayed.
Introduction Introduction Error codes are required to indicate failures in the TV set. In ComPair (Computer Aided Repair) is a Service tool for Philips principle a unique error code is available for every: Consumer Electronics products. and offers the following: •...
EN 20 LC8.2HA LA Service Modes, Error Codes, and Fault Finding Table 5-2 Error code overview The Blinking LED Procedure Error Item 5.6.1 Introduction code Description Remarks No error. The software is capable of identifying different kinds of errors. DC Protection of speakers.
Page 21
Service Modes, Error Codes, and Fault Finding LC8.2HA LA EN 21 Fault Finding and Repair Tips 5.8.3 Start-up/Shut-down Flowcharts On the next pages you will find start-up and shut-down Notes: flowcharts, followed by a trouble shooting flowchart, which • It is assumed that the components are mounted correctly might be helpful during fault finding.
Page 22
EN 22 LC8.2HA LA Service Modes, Error Codes, and Fault Finding AC ON V1.0 LC08R 21 Aug 2007 Start Up +3V3STBY Available M16C POR by +3VSTBY 160ms STANDBY = HIGH InitCold Component: 1. Check SDM port. Error 6 - NVM...
Page 23
Service Modes, Error Codes, and Fault Finding LC8.2HA LA EN 23 STANDBY / TACT SWITCH STANDBY Start Mute Audio (ANTI_PLOP=LOW) Send Standby command to Digital Module (MUTEn =HIGH) BL_ADJ Wait for 2s (PWM duty cycle 100%) Ack received from Digital Module or > 2s...
Page 24
EN 24 LC8.2HA LA Service Modes, Error Codes, and Fault Finding Start Power Down INT: AC OFF or Transient INT Avoid false trigger Poll the Power Down INT for 5 times Mute Audio & VIdeo Notes: 1. Power Down INT will based on fall edge triggering 2.
Page 25
Service Modes, Error Codes, and Fault Finding LC8.2HA LA EN 25 Code I_17760_049.eps 030308 Figure 5-11 Troubleshooting flowchart 2009-Apr-10...
EN 26 LC8.2HA LA Alignments 6. Alignments Index of this chapter: Software Alignments 6.1 General Alignment Conditions 6.2 Hardware Alignments With the software alignments of the Service Alignment Mode 6.3 Software Alignments (SAM) the Tuner and RGB settings can be aligned.
Alignments LC8.2HA LA EN 27 If you do not have a colour analyser, you can use the default Option Settings values. This is the next best solution. The default values are average values coming from production (statistics). 6.4.1 Introduction •...
Page 28
EN 28 LC8.2HA LA Alignments Option Bit Overview Below find an overview of the Option Codes on bit level. Table 6-4 Option codes at bit level (OP1-OP7) Option Byte & Bit Dec. Value Option Name Description Byte OP1 Bit 7 (MSB) ON = BBE is available;...
Introduction • Interactive via 3rd-party set-top box. The LC8.2HA LA is the Hospitality version of the LC8.2A LA Refer to figure “LC08R Architecture” for details. chassis. Refer to the Service Manual of the LC8.2A LA chassis for a description of all circuits outside the iBoard scope.
Page 30
EN 30 LC8.2HA LA Circuit Descriptions iBoard RS232 in/out RS232 12V out CVBS in/out 18510_203_090407.eps 090407 Figure 7-2 iBoard block diagram The iBoard intercepts the information from the IR Receiver and has full control over its interpretation and processing. It may also relay the same commands to the TV or send different IR commands to the TV.
IC Data Sheets LC8.2HA LA EN 31 8. IC Data Sheets IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
Page 32
EN 32 LC8.2HA LA IC Data Sheets 8.1.2 Diagram B07A, Type SIL9185 (IC7M07), HDMI switch Block Diagram H_17370_074.eps 100807 Figure 8-2 Internal block diagram 8.1.3 Diagram B07B, Type SIL9125 (IC7N01), HDMI receiver Block Diagram H_17370_075.eps 100807 Figure 8-3 Internal block diagram...
Page 33
IC Data Sheets LC8.2HA LA EN 33 8.1.4 Diagram B04A, Type SVP WX69 (IC7C01), Trident Video processor Block Diagram Luma NTSC/PAL/ Deinterlacer SECAM CVBS1 Cubic4 3:2/2:2 pull Scalar 3D Comb Gamma LUT down Decoder/ ICSC BMNR CVBS1 chroma Motion S-Video...
Page 34
EN 34 LC8.2HA LA IC Data Sheets 8.1.5 Diagram B05A, Type MSP4450P (IC7411), Micronas Sound Processor Block Diagram Loud- Sound IF1 Pre- speaker DAC/ modulator processing Sound Sound IF2 High- Processing Resolution Center internal / Subwoofer external Audio Delay Headphone...
Page 35
IC Data Sheets LC8.2HA LA EN 35 8.1.6 Diagram B05B, Type TDA8932T (IC7A01), Audio Amplifier Block Diagram BOOT1 OSCILLATOR DDP1 IN1P DRIVER HIGH OUT1 CTRL MODULATOR DRIVER SSP1 IN1N MANAGER BOOT2 INREF DDP2 IN2P DRIVER HIGH OUT2 CTRL MODULATOR DRIVER...
Page 36
EN 36 LC8.2HA LA IC Data Sheets 8.1.7 Diagram HC01, Type ST3232C (IC7107), RS232 Driver PIN CONFIGURATION PIN DESCRIPTION ° Positive Terminal for the first Charge Pump Capacitor Negative Terminal for the first Charge Pump Capacitor Positive Terminal for the second Charge Pump Capacitor...
Page 37
IC Data Sheets LC8.2HA LA EN 37 8.1.8 Diagram HC01, Type NCP303LSN45 (IC7103), Voltage Detector Block Diagram Pin Configuration NCP303LSNxxT1 NCP302xSNxxT1 Open Drain Output Configuration Complementary Output Configuration Input Input Reset Output Reset Output Input Reset Output N.C. Ground xxx = 302 or 303 = Y ear Inverter for active low devices.
Page 38
EN 38 LC8.2HA LA IC Data Sheets Personal Notes: 10000_012_090121.eps 090121 2009-Apr-10...
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 51 10. Circuit Diagrams and PWB Layouts Main Power Supply (42"): Part 1 DISPLAY SUPPLY (37" & 42"): PART 1 1K /1W R904 1N4007 5.1/1206 75/1206 75/1206 75/1206 1KP/1206 BAV70 D716 R950...
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 52 Main Power Supply (42"): Part 2 DISPLAY SUPPLY (37" & 42"): PART 2 0.1/FUS E RE S R317 4403 Q303 R301 BAS316 D302 ST P11NM60 Q301 D310 R315 BAS316 T301 R313...
Page 53
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 53 Layout Main Power Supply (42") (Top Side) H_16750_070.eps 110108 2009-Apr-10...
Page 54
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 54 Layout Main Power Supply (42") (Bottom Side) H_16750_071.eps 110108 2009-Apr-10...
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 59 SSB: Trident WX69 1C24 B7 3C44 D3 TRIDENT - WX69 2C01 A6 3C45 G13 B04A B04A 2C02 B6 3C46 H8 Pin Name Pin No 1(HIGH) 0(LOW) 2C03 B9 3C47 H13 Use ALE to latch Address Use Falling Edges of WR#&RD# to latch Address(*)
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 74 SSB: SRP List Explanation Example Personal Notes: 1 . 1 . Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Re ference Protocol) is a softw are too l that creates a list w i th all refer e n c es to signal lines. The list contains...
PCB SB IR 2007-09-21 3139 123 63274 2007-10-24 PCB MB ME8 IR : 3139_123_63263_02 NAME Chen Li Min SUPERS. **** *** ***** PCB SB ME8 IR : 3139_123_63273_02 "P00" ~ "P99" CHECK DATE 2007-05-23 ROYAL PHILIPS ELECTRONICS N.V. 2007 18510_500_090407.eps 090407 2009-Apr-10...
Page 87
Circuit Diagrams and PWB Layouts LC8.2HA LA EN 87 Layout Front IR / LED Panel (Top Side) 1P09 A4 1P10 A5 1P11 A1 2P12 A1 2P13 A1 I_17760_035.eps 3139 123 6327.4 090410 Layout Front IR / LED Panel (Bottom Side)