Canon VB-M741LE Installation Manual

Network Camera
Installation Guide
/
Please be sure to read the "Safety Precautions" section for correct use. After reading this
Installation Guide, keep it in a readily accessible location for future reference.
* Some cameras are not available in certain countries or regions.
Caution Request a professional installer for all installation work. Never try to install the
camera yourself. Doing so may result in unforeseen accidents such as dropping
the camera or electric shock.
Check Included Items
Camera, Screws (M4) x 4 Template
Installation Guide (This document) Setup CD-ROM
Warranty Card Ceiling Plate
I/O Interface Cable (BK2-0035-000) Safety Wire, Screws (M3) x 1
Power Interface Cable Dedicated wrench
Waterproofing tape Waterproofing explanation sheet
Symbols Indicating Camera Model
Camera specific functions will be listed using the symbols below.
: VB-M741LE : VB-M740E
Accessories
The following accessories can be purchased separately as necessary. Some accessories are not
available in certain countries or regions.
Conduit Box CB740-VB
Dedicated accessory used to protect wiring cables that cannot be stored above the ceiling. This can
be attached to the composite pipe.
Pendant Mounting Kit PC640-VB
Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings,
such as in big-box stores.
Weather Shield WS700-VB
Dedicated accessory to protect the main camera from rain.
Canon AC Adapter PA-V18
Dedicated AC adapter for this camera.
© CANON INC. 2017
Part Names
5 6 7 8 9
1
4
10
11
12
2 3
17
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
13 14 15 16
1. Lens protector / 2. LED (Orange) / 3. LED (Blue)* / 4. Notched cap /
5. Power connection terminal / 6. External device I/O terminals /
7. Audio input terminal (Black) (common LINE IN and MIC IN) /
8. Audio output terminal (White) (LINE OUT) / 9. 100Base-TX LAN connector
10. Pan axis adjustment screw / 11. Tilt axis adjustment screw /
12. Rotation axis adjustment screw / 13. Memory card slot / 14. Reset switch / 15. LED (Blue)* /
16. Reboot switch / 17. Memory card cover
* On: when powered on, during reboot, during normal use / Off: when [Turn Off] is selected
(please refer to the "Operation Guide")
The contents of this guide are subject to change without any prior notice.
BIE-7189-000
ENGLISH
External Dimensions
60 (2.36) 60 (2.36)
4-M4 (*1, *2)
Camera mounting
tab slots
Screw hole for attaching
214 (8.43)
102 (4.02)
85.7 (3-3/8) (*3, *4)
83.5 (3-9/32) (*4)
7.0 (0.28)
46.0 (1-13/16) (*4)
4-M4 (*7)
Camera
mounting tabs
Unit: mm (in.)
Before Installing the Camera
Printed in Japan
Set the IP address and other network information on the camera using the "Camera Management
Tool" on the Setup CD-ROM.
For details on how to operate the "Camera Management Tool", please refer to the "Camera
Management Tool User Manual".
Using a Memory Card
Loosen the screws with the dedicated wrench, open the
memory card cover, and then place the memory card in
the memory card slot. Once the memory card is in place,
close the memory card cover and tighten the screws with
the dedicated wrench.
To remove the memory card, push it in all the way until
the card slightly pops out and remove.
Important
• Insert a memory card before installing the camera.
• When using a memory card with the camera for the first
time, it is recommended to format the card after inserting it
into the camera (please refer to the "Operation Guide").
• Always unmount the memory card before removing it
(please refer to the "Operation Guide").
Memory card slot
Once this has been completed, close the memory card cover and tighten the screws with the
dedicated wrench.
Installing the Camera
1
Directly attached to ceilings/Directly attached to walls
1 -1 1 -2
Ceiling Installation
a
a
Wall Installation
a. Template
1 -3 b
b. Ceiling Plate
If the cables cannot be stored above a ceiling
If the cables cannot be stored above the ceiling, such
as with concrete ceilings, remove the notched cap at
the camera joint section with the dedicated wrench,
and create an opening for the cable to pass through.
151 (5.94)
The cables can be stored with the use of the conduit box
CB740-VB (sold separately), which can also be attached
to the composite pipe. Please refer to the installation guide
included with the conduit box for the installation method.
Attaching to a junction box
288 (11.34) Unit: mm (in.)
Attach the ceiling plate to the junction box after confirming the
fixing holes locations with the external dimensions diagram.
Ceiling pendant mounting
*1 Ceiling plate mount holes
Mount using the Pendant Mounting Kit (sold separately).
*2 Option unit mount holes
For details please refer to the Installation Guide included with the kit.
*3 Ceiling/Wall mount holes position
*4 Junction box fixing holes position
1 -1
*5 Ceiling/Wall mount holes
*6 Junction box fixing holes
*7 Camera mounting holes
Greater than 25 mm (1.0 in.)
Pass necessary cables
for connecting the camera
through the pipe.
2
❸
Note
Pass the safety wire through
the slit and attach it to the
hook on the rear side .
c. Safety wire
3
d
e
d. I/O interface cable
e. Power interface cable
b 4
Dedicated
wrench
6
Notched
cap
Adjusting the pan axis
1 -2
❷
❸
❶
M3*
Adjusting the tilt axis
❹
* Included
M4* × 4
with Pendant
Mounting Kit
❷
❷
Dedicated
Adjusting the rotation axis
wrench
c ❶
M3
Screws (included)
❶
7
When the installation has finished, please adjust the camera angle. For more information,
please refer to the "Operation Guide".
When the temperature within the camera is low (heater activated)
When the unit is powered by a 24 V AC/ PoE+ power source, the heater unit can be used.
Note
The heater unit will be activated automatically when the temperature within the camera is low. The
Completely wrap the cable connection with orange LED will be lit, until the camera has warmed up enough to start transferring video.
waterproof tape to the cable jacket, so as not
Once the temperature within the camera has reached the level where it can transfer the video
to allow water to enter between the individual
once again, the orange LED will turn off.
cables.
5
M4 × 4
Screws
(included)
Dedicated
wrench
Use the dedicated wrench to adjust the
following three rotation axes to set the angle.
❺
❶
❷
❹
❸
❹
❶
❸
Note
Shake the unit after tightening the screws. If the joint
section appears to wobble, further tighten the screw.
❸
❷