Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lightware DVI-TP-RX100
Summary of Contents for Lightware DVI-TP-RX100
- Page 1 DVI-TP-TX200 DVI-TP-TX300 DVI-TP-RX100 User's Manual...
- Page 2 Page 2 / 29...
-
Page 3: Safety Instructions
DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 SAFETY INSTRUCTIONS Class II apparatus construction. This equipment should be operated only from the power source indicated on the product. To disconnect the equipment safely from power, remove the power cord from the rear of the equipment, or from the power source. -
Page 4: Declaration Of Conformity
DECLARATION OF CONFORMITY Lightware Kft. 1071 Budapest Peterdy str. 15 HUNGARY as manufacturer declare, that the products DVI-TP-TX200 DVI-TP-TX300 DVI-TP-RX100 ( Computer Monitor Extender ) in accordance with the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EEC is in conformity with the following standards: EMI/EMC ........ -
Page 5: Table Of Contents
......................13 RONT AND REAR VIEW 2.9.1. Front view of DVI-TP-TX200/TX300 ................13 2.9.2. Rear view of DVI-TP-TX200/TX300 ................14 2.9.3. Front view of DVI-TP-RX100 ..................15 2.9.4. Rear view of DVI-TP-RX100 ..................16 2.10...................... 17 LECTRICAL CONNECTIONS 2.10.1. -
Page 6: Introduction
Introduction Dear Customer, Thank you for choosing Lightware DVI-TP series transmitters and receivers. DVI- TP-TX200/TX300 and DVI-TP-RX100 are Single Link DVI over Twisted Pair extenders which allow video signals 1920x1200@60Hz 2048x1080@60Hz resolution to be transmitted through 50 meters of high quality CAT7 cables. -
Page 7: Receiver Features (Dvi-Tp-Rx100)
RX100 supports +5V 500 mA constant current output on DVI OUTPUT to power long distance fiber optical transmitters. Universal power adaptor – DVI-TP-RX100 is equipped with a universal +5V power adaptor, which accepts AC voltages from 100 to 240 Volts with 50 or 60 Hz line frequency. -
Page 8: Understanding Edid
2.4.2. Common problems related to EDID Problem: „My system consists of the following: a PC, then a Lightware DVI-TP- TX200, a WUXGA (1920x1200) LCD as local monitor, then a DVI-TP- RX100 connected to a SXGA (1280x1024) projector. I would like to see the same image on the monitor and the projector. -
Page 9: Advanced Edid Management (Dvi-Tp-Tx200/Tx300)
EDID has been changed. You need to restart your source to make it read out the EDID again. Problem: „I have a DVI-TP-TX200/TX300 and I’m using a Lightware factory preset EDID. I would like to be able to choose from different resolutions, but my source allows only one resolution.”... -
Page 10: Fiber Cable Powering
Info DVI-TP-TX200/TX300 and DVI-TP-RX100 do not check if the connected sink (monitor, projector or other equipment) supports Hotplug or EDID signals but output the input signal immediately after it has been applied to the input. -
Page 11: Applications
DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 2.8. Applications Typical stand-alone application (TX200) Typical stand-alone application (TX300) Page 11 / 29... - Page 12 Using with Lightware MX-DVI-FR32R frame (the frame is equipped with single link DVI-D cards and single link DVI-TP cards) Page 12 / 29...
-
Page 13: Front And Rear View
DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 2.9. Front and rear view 2.9.1. Front view of DVI-TP-TX200/TX300 Address selection Status LEDs DVI Input connector Learn EDID button EDID Address The rotary switches select one of 100 addresses. Addresses 1…50 are factory preset and 51…99 are user programmable. Address 00 enables transparent mode. -
Page 14: Rear View Of Dvi-Tp-Tx200/Tx300
CATx Output(s) Connect one or two CAT5, CAT5e, CAT6a or CAT7 (recommended) cables between DVI-TP-TX200/TX300 and the receiver (DVI-TP-RX100 or Lightware Hybrid Matrix equipped with twisted pair input cards). DVI-TP-TX200/TX300 does... -
Page 15: Front View Of Dvi-Tp-Rx100
EQ level adjust knob EQ mode selector button EQ mode status LEDs Two LEDs indicate whether the DVI-TP-RX100 is in auto or manual equalization mode. Automatic mode usually gives a good result, but at long distances, manual equalization may be necessary. -
Page 16: Rear View Of Dvi-Tp-Rx100
TX200/TX300 or Lightware Hybrid Matrix equipped with twisted pair output cards). The DVI-TP-RX100 does not have networking capabilities. Do not connect the RJ45 input of the DVI-TP-RX100 to a Local Area Network device or a PC. Doing so may damage the unit! DVI output... -
Page 17: Electrical Connections
User’s Manual Rev. 1.0 2.10. Electrical connections 2.10.1. DVI inputs and outputs DVI-TP-TX200/TX300 and DVI-TP-RX100 provide 29 pole „digital only” DVI-I connectors for input and output connections. Always use high quality DVI cable for connecting sources and displays. Signal Signal... -
Page 18: Operation Of Dvi-Tp-Tx200/Tx300
Info If none of the LEDs light up upon power-up, the unit is most likely damaged and further use is not advised. Please contact support@lightware.hu 3.2. Learning the EDID The factory preset EDIDs cannot be changed by the user. Only addresses from 51 to 99 are user programmable. -
Page 19: Switching The Edid
OFF and ON again. 3.4. Factory preset EDID list Lightware factory pre-loaded EDIDs are specially provided to force graphic cards to output only the exact pixel resolution and refresh rate. Universal EDID (address 49) allows multiple resolutions including all common VESA defined resolutions. -
Page 20: Operation Of Dvi-Tp-Rx100
After the system is complete, connect the output of the +5V Power Adaptor to the DVI-TP-RX100 (further on RX100). The unit is immediately powered After being powered on, the RX100 displays its firmware version using the EQ mode status LEDs. -
Page 21: Maximum Twisted Pair Distances
Check the incoming signal Check the Signal Present LED on the front side of the DVI-TP-RX100. This LED indicates the presence of an active incoming DVI clock signal. If it is not illuminated, then no DVI clock signal is present at the VIDEO INPUT connector. - Page 22 Check the display status Check the Monitor Hotplug LED on the front side of the DVI-TP-RX100. This LED indicates the presence of the Hotplug signal coming from the attached display device. If it is not illuminated, then your display is not powered or not configured properly.
-
Page 23: Mechanical Drawings
DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 Mechanical Drawings 6.1. DVI-TP-TX200/TX300 6.1.1. Top view 100,4 mm 67,6 mm 6.1.2. Front view (controls and input) 26 mm 100,4 mm Page 23 / 29... -
Page 24: Rear View (Outputs And Power)
6.1.3. Rear view (outputs and power) 26 mm 100,4 mm 6.1.4. Bottom view 16.4 mm 2x M3 thread 16.5 mm 16,4 mm For rack mounting, cross recessed M3 (max. 10 mm long) screws must be used. Page 24 / 29... -
Page 25: Dvi-Tp-Rx100
DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 6.2. DVI-TP-RX100 6.2.1. Top view 100,4 mm 67,6 mm 6.2.2. Front view (controls) 26 mm 100,4 mm Page 25 / 29... -
Page 26: Rear View (Inputs, Output And Power)
6.2.3. Rear view (inputs, output and power) 26 mm 100,4 mm 6.2.1. Bottom view 16.4 mm 2x M3 thread 16.5 mm 16,4 mm For rack mounting, cross recessed M3 (max. 10 mm long) screws must be used. Page 26 / 29... -
Page 27: Warranty
Lightware Visual Engineering warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. The customer shall pay shipping charges when unit is returned for repair. Lightware will cover shipping charges for return shipments to customers. -
Page 28: Specifications
Specifications Video Standard ....................DVI 1.0 Color depth ................24 bits, 8 bit/color Format ..................... RGB only Data rate ......all between 25 Mbps and 1.65 Gbps /TMDS channel Resolutions ........all between 640x480 and 1920x1200@60Hz HDTV resolutions ..............720p, 1080i, 1080p HDCP compliant .................... - Page 29 DVI-TP-TX200/TX300/RX100 User’s Manual Rev. 1.0 NOTES: Page 29 / 29...