Metra Electronics CS-HDBTLPOE-70 User Manual

2. Connections

3. Bi-directional IR pass back

1 ) It supports bi-directional IR pass back . User can control DVD at RX
end and control TV at TX end.
2 ) If control at RX end, please connect IR blaster extension cable with
IR OUT of TX and connect IR receiver extension cable with IR IN of
RX. If control at TX end, please connect IR receiver extension cable
with IR IN of TX and connect IR blaster extension cable with IR OUT
of RX.

4. RS232 serial bi-direction passback function

1 ) Baud rate
Different encoding mechanism can not mix-connect, the baud rate
of RS232 serial of these transmitter unit and receiver unit, support
2400, 4800, 9600, 19200, 28800, 38400, 57600, and 115200
2 ) Line order
Check and make sure the RS23S serial line connect firmly and well,
and make sure serial data line is connected correctly as below:
If the RS232 serial does not work by following above connection,
please tr y to change the order of TXD line and RXD line.
GND
RXD
line
line
TXD
3 ) Check baud rate
If you need to check the baud rate at last time, firstly, before
power on, set the baud rate to 115200 on your serial port test tool .
Then, power on, when the RS232 serial of product connects to
serial port test tool, the software will read out the baud rate at
present.
e.g: software show information " Baud rate: 9600", means 9600
is the current baud rate.
4 ) Set baud rate
For example: the current baud rate is 9600, but the baud rate of
control equipment is 19200, so it needs to set the baud rate to 9600.
At this time, in serial port tool, choose baud rate "9600", then input
command "set: 19200" in character format and send it out.
· FAQ
Q: No output on screen?
A: 1 ) Firstly, please check and make sure the power supply is connected
well. Then, check and make sure all cables are connected correctly.
2 ) Please check and make sure you have chosen the right HDMI input
port of the TV/ screen.
3 ) Please check and make sure there is HDMI signal to be fed into
transmitter unit, and check whether the receiver unit has been
connected well with the display device.
Q: No"3"led indicator kepps flashing and no output?
A: Check and make sure the HDMI display device has been switched to
the right HDMI input channel.
Q: No"3"led indicator kepps flashing, and no "3"led indicator
keeps off?
A: Check whether the TX's HDMI IN has signal input and make sure RX's
OUT is well connected with HDMI display.
Q: Output image with snow point?
A: Change the HDMI cable between the transmitter unit and the source
device, it will be better to use a shorter HDMI cable for re-testing.
· Specification
Items Specifications
HDMI signal 4Kx2K,compatible with HDCP,support CEC and 24bits deep color
Resolution
480i/480P/576i/576P/720P/1080i/1080P/3D/4Kx2K
Supported
Audio LPCM、DTS Digital, Dolby Digital
Network cable CAT6、CAT6A、CAT7
CAT6 70m
Transmission
1080p@60Hz 48bpp, 1080p@60Hz 3D,
CAT6A 70m
length
4Kx2K@60Hz
70m
CAT7
Support 20~60kHz wide frequency devices and Bi-directional IR
Infrared back
transmission
Working
0～55℃
temperature
Storage
-10～70℃
temperature
Humidity 0～90%(no condensation)
Power supply DC12V/2A
Power
TX: ＜6W; RX: ＜8W
consumption
Product
109.49(L)x87.0(W)x23.4(H)mm
dimension
Material
Iron alloy material
Weight TX:240g RX:250g
Color
Black

Disclaimer

The product name and brand name may be registered trademark of
related manufacturers.TM and ® may be omitted on the user manual.
The pictures on the user manual are just for reference, and there may
be some slight difference with the real products.
We reser ve the rights to make changes without further notice to a
product or system described herein to improve reliability, function or
design.
70m HDMI HDBaseT Extender
User manual
60Hz