Zone Settings (Zone) - Roland Piano Owner's Manual

Creating a Performance
D Beam
Switch (D Beam Switch)
Switches the D Beam controller on/off.
Value: OFF, ON
Assign (D Beam Assign)
Specifies the function controlled by the D Beam controller.
Value
OFF: The D Beam controller will not be used.
CC01–31, 33–95: Controller numbers 1–31, 33–95
For more information about Control Change messages, please
refer to "MIDI Implementation" (Sound/Parameter List).
BEND UP: Raises the pitch in semitone steps (up to 4 octaves
higher).
BEND DOWN: Lowers the pitch in semitone steps (up to 4 octaves
lower).
AFTERTOUCH: Aftertouch
NOTE: Play the sound of the most recently pressed key.
OCT UP: Raises the key range in octave steps (up to 3 octaves
higher).
OCT DOWN: Lowers the key range in octave steps (up to 3 octaves
lower).
START/STOP: Starts/Stops the sequencer.
TAP TEMPO: Tap tempo (a tempo specified by the interval at which
you move your hand over the D Beam controller).
ARP SWITCH: Switches the Arpeggiator on/off.
ARP VAR: Arpeggio Variation
ARP ACCENT: Arpeggio Accent Rate
ARP SHFFLE: Arpeggio Shuffle Rate
ARP OCT UP: The range in which the arpeggio is sounded will rise
in steps of an octave (maximum 3 octaves).
ARP OCT DW: The range in which the arpeggio is sounded will
lower in steps of an octave (maximum 3 octaves).
PTN SWITCH: Switch Rhythm pattern playback on/off.
PTN ACCENT: Rhythm Pattern Accent Rate
PTN SHFFLE: Rhythm Pattern Shuffle Rate
Polarity (D Beam Polarity)
Switch the polarity of the D Beam controller.
With a setting of "REVERSE," the direction of control for the D Beam
controller will be inverted.
Range: STANDARD, REVERSE
Range Lower (D Beam Range Lower)
Specify the lower limit of the range of the D Beam controller. Values
below this setting will not be output.
Value: 0–UPPER
Range Upper (D Beam Range Upper)
Specify the upper limit of the range of the D Beam controller. Values
above this setting will not be output.
Value: LOWER–127
98
Zone (D Beam Zone Number)
Specify the zone that will be controlled by the D Beam controller.
The effect will apply to the part that is connected to the zone you
specify here.
Value: 1–16

Zone Settings (Zone)

fig.05-08_50
For details on the setting, refer to "How to Make the
Performance Settings" (p. 91).
Transmit Channel
Specifies the MIDI transmit channel for each zone.
Value: 1–16
Int Switch (Internal Switch)
Specifies, for each zone, whether or not the keyboard controller
section will be connected to the internal sound generator.
Normally this is left "ON," but if you wish to use the Fantom's
keyboard and controllers to control only external sound modules, set
it to "OFF."
Value: OFF, ON
Ext Switch (External Switch)
Determines, for each zone, whether or not data generated by the
keyboard controller section is sent as MIDI messages from the MIDI
OUT connector.
Normally you will leave this "ON," but you can turn it "OFF" when
you do not want the Fantom to control external sound generators.
Value: OFF, ON
Ext Bank Select MSB (External Bank Select
MSB)
If you want a Bank Select number MSB (controller number 0) to also
be transmitted when you switch performances, specify the value that
you want to transmit (0–127) for each zone. If you do not want this
message to be transmitted, set this to "---."
Value: 0–127, ---
The data of the zone for which the External Switch is turned off
will not be transmitted.