Advertisement
Weight
Approx. 1710 g (3.77 lb.)
Impact Resistance
IK10 (20J)
Dust-resistant/
Waterproof Specification IP66
Connecting the Camera
Multi-Cable
To prevent cable connections from shorting out, wrap each individual connection with insulating
tape, and then wrap all of the cables with waterproofing tape.
Power Connection
Power can be supplied to the camera in the three ways described below. Please be sure to read
the user manual for the dedicated power supply before use.
Note
• Power supply should conform to all local codes.
• The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.
• Please use 24 V AC as a power source when using the Heater Unit HU641-VB (sold separately). PoE,
12 V DC and AC Adapters cannot be used.
PoE (Power over Ethernet)
The camera supports PoE functions. Power can be supplied to the camera by using a LAN cable
connected to a PoE HUB that conforms to the IEEE802.3at Type1 standard.
Power can also be supplied to the camera by using the included multi-cable
Important
• Check with your dealer for more information about PoE HUB and Midspan technology.
Midspan (a LAN cable power supply device) is a device that, like a PoE HUB, supplies power to the
camera via a LAN cable.
• Some PoE HUBs allow the limitation of power for each port, but applying limits may interfere with
performance. If using this type of PoE HUB, do not limit the operating power.
• Some PoE HUBs have limits for the total power consumption for the ports, which can interfere with
performance when multiple ports are in use. For more information, check the instruction guide for your
PoE HUB.
• When the camera is connected to both a PoE HUB and an external power supply (12 V DC or 24 V
AC), power from the power supply first connected is given priority. But when both power supplies are
connected, according to the combination, problems such as failure of the network connection may
occur. If a problem arises, disable one of the power supplies.
External Power Supply
2
12 V DC or 24 V AC input can be used. Use the included multi-cable to connect to the camera
power connection terminal. 12 V DC can be connected in a non-polar configuration.
1: BROWN (fat) 24 V AC / 12 V DC non-polar
2: BLUE (fat) 24 V AC / 12 V DC non-polar
3: GREEN (fat) FG (frame ground)
Important
• The power supply should be within the following voltage range.
• 24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less)
Current supply capacity of at least 1.0 A per camera
• 12 V DC: Voltage fluctuation within ±10% of 12 V DC
Current supply capacity of at least 1.5 A per camera
• When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0
series to the power line.
• For an external power supply, use a double-insulated device.
Recommended Power Cables [Reference]
Cable (AWG)
24
12 V DC maximum cable length m
5
(ft.)
(16.4)
24 V AC maximum cable length m
11
(ft.)
(36.1)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
AC Adapter
Please use the dedicated AC adapter (sold separately).
Remove the power connector attached to the AC adapter, then connect the multi-cable included
in the package to the power connector, as shown in the following diagram.
Green (fat) Blue (fat)
2
Multi-Cable
RJ45 Coupler (included)
1
3
1
8
OUT (White)
IN (Black)
1
.
22
20
18
9
14
23
(29.5)
(45.9)
(75.5)
18
29
46
(59.1)
(95.1)
(150.9)
AC Adapter
White
Brown (fat)
Black
Insulate
External Device I/O Terminals
External device I/O terminals consist of two input and output systems each. Viewer can be used
to check external device input status and control output to an external device (please refer to
"Operation Guide").
Use the included multi-cable to connect to external device input/output terminals.
1: BROWN External device input 1 IN1 (+)
2: BLACK
External device input 1 IN1 (-)
3: RED
External device input 2 IN2 (+)
4: GRAY
External device input 2 IN2 (-)
External Device Input Terminals (IN1, IN2)
1
External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative
terminals connected to the camera interior GND. Connecting cables to the positive and negative
2
terminals and opening or closing the circuit notifies the Viewer.
3
Important
4
When connecting sensors and switches, connect terminals that are electrically isolated from the respective
power and GND.
External Device Output Terminals (OUT1, OUT2)
External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets
have no polarity. Controls from the Viewer can be used to open and close the circuit between
the terminals. Using optical couplers, the output terminals are isolated from the camera's internal
circuit.
The load connected to the output terminals should
be within the following rating range.
Rating between output terminals:
Maximum voltage 50 V DC
Continuous load current at or below 100 mA
On resistance: Max. 30 Ω
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker with
an amplifier allows you to send/receive audio through the Viewer.
Use the included multi-cable to connect audio input/output devices to the camera.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect an audio output device with
the multi-cable.
Audio Input Terminal Common LINE IN/MIC IN (monaural input)
Although the camera only has a single audio input system, it supports two types of microphone
input: LINE IN and MIC IN. Before using the audio input, please confirm the [Audio Input] in the
Setting Page (please refer to "Operation Guide"). LINE IN is selected by default.
Input terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
• Dynamic MIC IN
Input impedance: 1.5 kΩ ±5%
Supported microphones: Output impedance: 400 – 600 Ω
• Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 kΩ ±5%
Microphone power supply: plug-in power (voltage: 2.3 V)
Supported microphones: Condenser microphones with plug-in power support
• LINE IN
Input level: Max. 1 Vp-p
– Use a microphone with an amplifier.
Audio Output Terminal LINE OUT (monaural output)
Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from Viewer.
Output terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
Output level: Max. 1 Vp-p
– Use a speaker with an amplifier.
/20 W in
Ω
16
32
(105.0)
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
64
These symbols indicate that this product is not to be disposed of with your household waste,
(210.0)
the Battery Directive.
This product should be handed over to a designated collection point, e.g., on an authorized
one-for-one basis when you buy a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE) and batteries and accumulators.
Improper handling of this type of waste could have a possible impact on the environment and
human health due to potentially hazardous substances that are generally associated with EEE.
Your cooperation in the correct disposal of this product will contribute to the effective usage of
natural resources.
For more information about the recycling of this product, please contact your local city office,
waste authority, approved scheme or your household waste disposal service or visit www.
canon-europe.com/weee, or www.canon-europe.com/battery.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
© CANON INC. 2016
3
5: ORANGE External device output 1 OUT1
6: YELLOW External device output 1 OUT1
7: GREEN
8: BLUE
4
according to the WEEE Directive (2012/19/EU), the Battery Directive
(2006/66/EC) and/or national legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy metal
(Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or
accumulator at a concentration above an applicable threshold specified in
External device output 2 OUT2
External device output 2 OUT2
Internal Connection Diagram
+3.3 V
1 kΩ
10 kΩ
10 kΩ
Input terminal
External device
IN1, IN2
0.1 µF
External device
Output terminal
OUT1, OUT2
Printed in Japan
Advertisement
