Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
i-mop XL
230/240/115 Volt
Model Number:
IMOPXL.FCT.1107C
IMOPXL.FCT.1207C
IMOPXL.FCT.1307C
IMOPXL.FCT.2507C
Read these instructions
The device is only suitable
before using the i-mop
for indoor use; do not
expose the device to rain.
Read these Safety
WARNING:
Instructions before
Strong Magnets
operating
2017/06
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for i-team IMOPXL.FCT.1107C
Summary of Contents for i-team IMOPXL.FCT.1107C
- Page 1 INSTRUCTION MANUAL i-mop XL 230/240/115 Volt Model Number: IMOPXL.FCT.1107C IMOPXL.FCT.1207C IMOPXL.FCT.1307C IMOPXL.FCT.2507C Read these instructions The device is only suitable Read these Safety WARNING: before using the i-mop for indoor use; do not Instructions before Strong Magnets expose the device to rain.
- Page 2 THANK YOU FOR CHOOSING THE i-mop Please read this manual carefully for important safety information and operating instructions before using the i-mop. Keep this manual for future reference because it contains important information. This i-mop will provide excellent performance, but the best results will be obtained if the i-mop is: •...
-
Page 3: Product Description
• Dress safely. Do not wear a necktie, scarf, or Model Number: any loose or dangling clothing or jewelry while IMOPXL.FCT.1107C EUROPE operating this i-mop because they can tangle in IMOPXL.FCT.1207C UNITED KINGDOM rotating parts, causing serious injury or death. - Page 4 DANGER Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. WARNING - Do not use water that exceeds 45°C / 113°F. Using water above this temperature, will void the Tank Warranty. - Do not use cleaning solution with pH below 3 or above 11 in order to prevent damage to sensitive components like hoses and valves.
- Page 5 SAFETY INSTRUCTIONS – BATTERY PACKS GENERAL PRECAUTIONS Read all the warnings before using the i-mop battery packs. • The battery packs are equipped with electronic thermal protection. Refer to the Temperature Range Table below for recommended operating conditions. • Always keep the battery packs clean and dry. •...
- Page 6 WARNING FIRST AID MEASURES If exposed to any of the battery chemicals, please follow the procedures below: Eyes - Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelid. - Seek medical attention. Inhalation - Vacate from site of exposure to fresh air immediately.
- Page 7 UNPACKING Place the box in a horizontal position on the floor, keeping enough space around you to work. Carefully cut along the top opening with a cutter. Remove the foam packing covering the i-mop and take out the boxes. Pull up the handle (90°), while grabbing the scrub deck. Squat down properly to avoid strain before lifting the i-mop. Place the i-mop on the floor in the “Park” position. CONTENTS Please make sure no items are missing by checking the contents against the above list.
-
Page 8: Initial Setup
INITIAL SET UP Set the i-mop in the “Park” position. For the initial setup or anytime the squeegee is not installed: pull the hose back up from the top while guiding the lower half back into the i-mop to make sure the vacuum hose will not be crimped during the following procedure. -
Page 9: Charging Battery Packs
CHARGING BATTERY PACKS You must charge the battery packs for at least 5 hours before you use the i-mop for the first time. Plug the supplied power cord into the charging dock before plugging it into an outlet. Align the specified battery packs with the charging dock and slide each battery pack in from the side until you hear a click. The battery packs are now fixed in position and ready for charging. -
Page 10: Installing Brushes
INSTALLING BRUSHES With the I-mop in the “Park” position, hold the scrub deck with one hand while using your other hand to align the brush with the motor disc. Look for and align the latches and cut-outs in the brush and motor disc. -
Page 11: Installing Battery Packs
INSTALLING SOLUTION TANK Fill the small tank with no more than 4L (1 gallon) of clean water or appropriate non-foaming detergent. Put the tank on the i-mop with the valve first. Press the tank downward to break the seal of the valve. INSTALLING RECOVERY TANK Put the bottom of the tank on the i-mop and allow the tank to automatically snap into position. (Magnetic action will lock the Recovery Tank into place.) If in doubt, you can push the tank further into the seal for optimum vacuum. -
Page 12: Operation
OPERATION Read and understand the Safety Instructions section of this manual before operating the i-mop. Filling the Solution Tank Always fill the i-mop tank with clean water maximum 4L (1 gallon) from a tap or hose. To prevent dirt from entering the Solution Tank, use only non-foaming detergent. Recovery Tank Make sure the fluid level of the Recovery Tank does not exceed 6L (1.5 gallon) to prevent damage to the i-mop. Note: Every time the Solution Tank is refilled, the Recovery Tank should also be emptied. Setting the i-mop in the “Operating Position” Crouch down and while holding the scrub deck with one hand, push the handle forward with the other hand. Bring the scrub deck slowly down to the floor. - Page 13 Selecting the Mode of Operation Choose the preferred mode on the i-mop operating panel: MODE 1: Brush + Water/Solution MODE 2: Brush (use the Brush only mode if the floor is very wet or to scrub stains) MODE 3: Brush + Dry Vacuum MODE 4: Brush + Water/Solution + Dry Vacuum ECO (Water Saving Mode) If you press the ECO water saving mode button once, the i-mop will use 40% less water until the ECO mode button is pressed again to turn off.
- Page 14 The i-mop scrub deck is designed to get as close as possible to walls. Approach walls diagonally with the edge of the i-mop and continue along the wall. Switching Off/Completing Cleaning Before you finish, switch the i-mop in the 3 “Brush + Dry” mode and operate it about 5-6 meters (15-20 ft) farther to vacuum up remaining solution. Then set the knob to the “OFF” position. Note that the vacuum motor will continue to run for approximately 3 more seconds.
- Page 15 Transporting/Moving the i-mop Inside a Building To move the i-mop from one location to another one in a building, put the i-mop in the “Park” position (described earlier). Hold the handle with one hand, and with the other hand, guide the scrub deck in the direction of the two transport wheels.
-
Page 16: Maintenance And Care
MAINTENANCE AND CARE After Each Use • Drain and rinse tanks with fresh water. • Wipe the Recovery Tank with fresh water and a clean, damp cloth. • Recharge the battery packs if needed. • Check to see if both brushes are clean and intact. Clean them under fresh water or replace them if necessary. - Page 17 How to Replace the Squeegee With the i-mop in the “Park” position, hold the scrub deck with one hand while pulling the left side of the squeegee off with the other hand. Switch hands afterwards and repeat for the right side. Detach the vacuum hose by twisting a 1/4 turn at the connector until the squeegee is loosened.
-
Page 18: Troubleshooting And Service
TROUBLESHOOTING AND SERVICE Poor Water Recovery Troubleshooting • Check the function of the suction motor. No power – i-mop won’t start • Inspect vacuum hose for any objects obstructing • Check if battery packs are fully charged. the airflow. • Ensure battery packs are properly installed. •... -
Page 19: Environment Protection
ENVIRONMENT PROTECTION The packaging materials can be recycled. Please do not throw the packaging material into household waste. Please recycle it. Old devices contain valuable materials that can be recycled. Rechargeable battery packs contain materials that should not be disposed of in landfills. Please dispose of old devices and battery packs and that they must be disposed of through suitable waste collection systems. -
Page 20: Exploded View
EXPLODED VIEW ITEM DESCRIPTION K.1.TU.IMOP.230.2/797 ASSEMBLY TOP UNIT K.1.S.72.0059.2/797 ASSEMBLY CONTROL UNIT ASSEMBLY INLET TUBE K.1.S.72.0040.0 HINGE WELDING ASSEMBLY TOP UNIT KIT K.1.S.72.0031.2 K.1.S.72.0035.0 VACUUM MOTOR KIT K.1.S.72.0111.357 MOTOR UNIT COVER KIT K.1.S.72.0039.0/3 UTP CABLE RJ 45 L 100 CM ASSEMBLY CLEAN COMPARTMENT COMPLETE K.1.S.72.0081.1 ASSEMBLY BATTERY PACK BLUE [LEFT]...
Need help?
Do you have a question about the IMOPXL.FCT.1107C and is the answer not in the manual?
Questions and answers