3M 10800 Instructions And Parts List
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Power Tool
  5. 10800
  6. Instructions and parts list

3M 10800 Instructions And Parts List

Upper and lower high speed taping heads 2 inch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Instructions and Parts List
3M-Matic
Type 10800
Upper and Lower
High Speed Taping Heads
2 Inch
Serial #:

Important Safety Information

BEFORE INSTALLING OR OPERATING THIS EQUIPMENT
Read, understand and follow all safety and operating instructions.

Spare Parts

It is recommended you immediately order the spare parts listed in the "Spare
Parts/Service Information" section. These parts are expected to wear through
normal use, and should be kept on hand to minimize production delays.
3M-Matic
Accuglide 3 - 2 Inch Taping Head
™
Page i
Accuglide
™
For reference, record machine serial number here.
3
™
NA - ENG
April 2017

Advertisement

Table of Contents
loading

Related Manuals for 3M 10800

Summary of Contents for 3M 10800

  • Page 1: Important Safety Information

    Instructions and Parts List 3M-Matic Accuglide ™ ™ Type 10800 Upper and Lower High Speed Taping Heads 2 Inch Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
  • Page 2 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page ii...

  • Page 3: Replacement Parts And Service Information

    Provide the customer support coordinator with the model/machine name, machine type, and serial number that are located on the identifi cation plate (For example: Accuglide 3 - 2 inch - Type 10800 - Serial Number 13282). To order replacement parts, contact us: CSPD division of Combi Packaging Systems LLC.
  • Page 4 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page iv...
  • Page 5 Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
  • Page 6 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page vi...

  • Page 7: Table Of Contents

    Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™...

  • Page 8: Equipment Warranty And Limited Remedy

    3M to its factory or other authorized service station designated by 3M. If 3M is unable to repair or replace the part within a reasonable time after receipt thereof, 3M, at its option, will replace the equipment or refund the purchase price.

  • Page 9: Intended Use

    ® seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines.
  • Page 10 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 2...

  • Page 11: Taping Head Contents / How To Use Manual

    (if it is possible, please have the manual name, part number, and revision information and/or model/machine name, machine type, and serial number) that are located on the identifi cation plate (For example: Model - Accuglide 3 - 2” - Type 10800 - Serial Number 13282).

  • Page 12: Important Safeguards

    The blades are extremely sharp. system is running (Important Safeguards continued on next page) NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 4...

  • Page 13: Important Safeguards

    See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™...

  • Page 14: Specifi Cations

    5. Box Size Capacities: For use with center seam regular slotted containers. When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifi cations for box weight and size capacities. 6. Operating Rate: Conveyor speeds up to 0.5 m/s [100 feet per minute].

  • Page 15: Dimensional Drawing

    * This dimension can be reduced to 90mm [3-1/2 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 7...

  • Page 16: Installation

    Taping Head is supplied with a buffi ng the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.

  • Page 17: Operation

    Spring One-Way Tension Roller Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side View) NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 9...

  • Page 18: Tape Loading - Upper Taping Head

    2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 10...

  • Page 19: Operation

    Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 11...

  • Page 20: Maintenance

    Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 12...

  • Page 21: Cleaning

    Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See Figure 4-2. NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 13...

  • Page 22: Adjustments

    - Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 14...

  • Page 23: Applying Mechanism Spring

    - Never attempt to work on the taping Figure 5-5 One-Way Tension Roller head or load tape while the box drive system is running (Adjustments continued on next page.) NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 15...

  • Page 24: Tape Leg Length

    - Never attempt to work on the taping cutoff blades under orange blade guards. head or load tape while the box drive The blades are extremely sharp. system is running NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 16...

  • Page 25: Troubleshooting Guide

    Make sure one-way bearing is contacting the taping head frame below the surface of the tension roller. If not, press bearing further into roller or replace roller. NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 17...

  • Page 26: Troubleshooting Guide

    Tape not centered on box seam Centering guides not centered Adjust centering guides Box fl aps not of equal length Check box specifi cations NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 18...

  • Page 27: Spare Parts/Service Information

    Roller – Buffi ng 78-8113-7030-9 Spring – Torsion Replacement Parts and Service Refer to the fi rst page of this instruction manual “Replacement Parts and Service Information". NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 19...
  • Page 28 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 20...

  • Page 29: Replacement Parts Illustrations And Parts List

    (continued) Replacement Parts Illustrations and Parts Lists AccuGlide™ 3 High Speed 2 Inch Upper Taping Head, Type 10800 AccuGlide™ 3 High Speed 2 Inch Lower Taping Head, Type 10800 1. Refer to the Taping Head Assemblies Figure to fi nd all the parts illustrations identifi ed by fi gure numbers.
  • Page 30 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 22...
  • Page 31 Tape Head Figures AccuGlide ™ 3 - 2 inch Figure 10401 Figure 10925 Figure 10924 Figure 10923 Figure 10922 Figure 10919 Figure 10921 Figure 10920 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 23...
  • Page 32 ™ AccuGlide 3 - 2" Figure 10925 – Upper Head NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 24...
  • Page 33 ™ AccuGlide 3 - 2" Figure 10925 – 2" Upper Head Ref. No. 3M Part No. Description 10925-1 78-8137-3294-4 Frame – Tape Mount Upper Assembly 10925-2 78-8137-3295-1 Frame – Front Upper Assembly 10925-3 78-8068-4143-9 Guide – #1 10925-4 78-8068-4144-7 Guide – #2...
  • Page 34 ™ AccuGlide 3 - 2" 12 11 Figure 10922 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 26...
  • Page 35 ™ AccuGlide 3 - 2" Figure 10922 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10922-1 78-8133-9509-8 Applying Arm #1 10922-2 78-8133-9510-6 Applying Arm #2 10922-3 78-8070-1221-2 Plate – Tape 10922-4 78-8070-1309-5 Shaft Roller 10922-5 78-8070-1367-3 Roller –...
  • Page 36 ™ AccuGlide 3 - 2" Figure 10919 – Upper Head NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 28...
  • Page 37 ™ AccuGlide 3 - 2" Figure 10919 – 2" Upper Head Ref. No. 3M Part No. Description 10919-1 78-8137-3300-9 Buffi ng Arm – Sub Assembly 10919-2 78-8137-3301-7 Buffi ng Arm – Sub Assembly 10919-3 78-8052-6575-4 Shaft – Roller 10919-4 78-8137-1398-5 Roller - Buffi...
  • Page 38 AccuGlide ™ 3 - 2" Figure 10923 – Upper and Lower Heads Figure 10923 Upper and Lower Heads NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 30...
  • Page 39 ™ AccuGlide 3 - 2" Figure 10923 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10923-1 78-8137-3302-5 Link – Assembly 10923-3 78-8137-3304-1 Shaft – Pivot, Buffi ng 10923-4 78-8017-9082-1 Bearing – Special 30 mm 10923-5 78-8017-9106-8 Screw –...
  • Page 40 ™ AccuGlide 3 - 2" Figure 10921 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 32...
  • Page 41 ™ AccuGlide 3 - 2" Figure 10921 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10921-1 78-8137-3307-4 Frame – Cut-Off Weldment 10921-2 78-8017-9173-8 Blade – 65 mm/2.56 Inch 10921-3 26-1003-8596-7 Screw - Hex Hd M5 x 8 w/ Ext. Tooth Lockwasher...
  • Page 42 ™ AccuGlide 3 - 2" Figure 10401 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 34...
  • Page 43 ™ AccuGlide 3 - 2" Figure 10401 – 2" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10401-1 78-8070-1395-4 Bracket – Bushing Assembly 10401-2 78-8076-4519-3 Shaft – Tape Drum, 50mm 10401-3 78-8017-9169-6 Nut – M18 x 1...
  • Page 44 ™ AccuGlide 3 - 2" 17 19 Figure 10924 – Lower Head NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 36...
  • Page 45 ™ AccuGlide 3 - 2" Figure 10924 – 2" Lower Head Ref. No. 3M Part No. Description 10924-1 78-8137-3296-9 Frame – Tape Mount Lower Assembly 10924-2 78-8137-3297-7 Frame – Front Lower Assembly 10924-3 78-8068-4144-7 Guide – #2 10924-4 78-8068-4143-9 Guide – #1...
  • Page 46 ™ AccuGlide 3 - 2" Figure 10920 – Lower Head NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 38...
  • Page 47 AccuGlide ™ 3 - 2" Figure 10920– Lower Head Ref. No. 3M Part No. Description 10920-1 78-8137-3300-9 Buffi ng Arm – Sub Assembly 10920-2 78-8137-3301-7 Buffi ng Arm – Sub Assembly 10920-3 78-8052-6575-4 Shaft – Roller 10920-4 78-8137-1398-5 Roller - Buffi ng Assembly...
  • Page 48 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 40...
  • Page 49 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 41...
  • Page 50 NA - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head ™ April 2017 Page 42...

This manual is also suitable for:

Accuglide 33m-matic accuglide 3

Table of Contents