Supermicro X10sBa-L Quick Reference Manual

S
UPERMICR
R
X10sBa(-L)
Q r g 1.0a
uICk eferenCe uIde

Motherboard Layout and Features

VGA
BIOS
AUDIO FP
JSPDIF_OUT
JD1
LAN2 LAN1
(for mini-PCI-E only)
J1
(for X10SBA only)
SP1
J2 (for X10SBA only)
(for M-SATA only)
(for X10SBA)
JBT1
JSD1
BT2 JP1
USB6
LED5 LED1
USB4/5 USB2/3
JTPM1

Back Panel I/O Connectors

B
D
E
A C F G
A. HDMI E. LAN1
B. DisplayPort F. LAN 2
C. USB0 (3.0) G. VGA
D. USB1 (2.0)
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
C I
ontaCt nformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
USB0(3.0)
FAN1
HDMI/DP
USB1(2.0)
J5
X10SBA(-L)
Rev. 1.01
CPU
BAR CODE
JDIMM1
SO-DIMM2 (1.35V only)
PJ1
JPW1
= mounting hole

Front Panel Control (JF1)

20 19
Ground
X
X X
3.3V
PWR LED
3.3V Stby
HDD LED
3.3V Stby
NIC1 Link LED
3.3V Stby
NIC2 Link LED
OH/Fan Fail/PWR Fail
LED Cathode
3.3 V
Power Fail LED
Reset Reset Button
Ground
PWR Power Button
Ground
2 1
guide.
Jumpers/Connectors/LED Indicators

Jumpers

JBT1 CMOS Clear Open: Normal Operation (Default)
Short: Clear CMOS
JPAC1 Audio Enable Pins 1-2 (Enabled)
JPME2 Intel Manufacturer Mode Select Pins 1-2 (Normal)
JPUSB1 USB Wake-Up Enable Pins 1-2 (Enabled)

Connectors

Connector Description
Audio FP Front Panel Audio Header
Battery Onboard Battery (BT2)
COM1-COM4 COM1/COM2/COM3/COM4 Headers
FAN1/FAN2 System Fan Headers
HDMI/DP (Backpanel) HDMI/DisplayPort
J1 mini-PCI-E Slot for a mini-PCI-E Card (Not available on the -L model)
J2 mSATA slot MUX (Multiplexer/Switch) with I-SATA1 (Not available on the
-L model)
J4 (Slot1) PCI-E 2.0 x 2 in x8 Slot
J5 (eDP) Embedded DisplayPort (eDP)
JD1 Power LED/Speaker Header (Pins 1-3: Power LED, Pins 6-7: Internal
Buzzer, Pins 4-7: External Speaker)
JF1 Front Panel Control Header
JOH1 Overheat LED Indicator Header
JP1 General Purpose I/O Header
JPW1 24-pin ATX Power Connector (Optional Power Source)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSPDIF_OUT S/PDIF (Sony/Phillips Digital Interconnect Format) Audio Output Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
PJ1 4-pin 12V DC Power Connector (Optional Power Source up to 144W)
I-SATA0/1 (Intel-)Serial ATA (SATA 2.0) Ports 0/1
M-SATA0/1/2/3 (Marvell 88SE9230) Serial ATA (SATA 3.0) Ports 0-3 (Not available on
the -L model)
SMBUS1 (JSMB1) 4-Pin External System Management Bus I C Header (JSMB1) (for slave
2
device)
SP1 Internal Speaker/Buzzer
USB 0 Backpanel USB 3.0 Port 1
USB 1 Backpanel USB 2.0 Port 2
USB 2/3, USB 4/5 Front Accessible USB 2.0 Connections: USB 2/3 (USB 3 is available
on the -L model)
USB 4/5 (Not available on the -L model)
USB 6 Front Accessible Type A USB 2.0 Connector (Not available on the -L
model)
VGA Backpanel VGA Port

LED Indicators

LED Description Color/State
LED1 Main Power LED Green: On
LED5 Standby Power LED Green: On
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
P C
aCkage ontents
• One (1) Supermicro Motherboard
• Six (6) SATA Cables (2 cables for the -L model)
• One (1) I/O Shield
• One (1) Quick Reference Guide

Memory Support

The X10SBA/X10SBA-L supports up to 8 GB of DDR3L (1.35, Low Voltage) Non-
ECC SO-DIMM of up to 1333 MHz in two horizontal sockets. Populating these DIMM
slots with a pair of memory modules of the same type and same size will result in
interleaved memory, which will improve memory performance.

DIMM Memory Installation

Insert the desired number of SO-DIMMs into the memory slots, starting with SO-
DIMM1, then SO-DIMM2.
1. Align the receptive point on the bottom of the SO-DIMM module against
the key on the memory socket. Note the notches on the side of the SO-
DIMM module and those on the socket to avoid causing damage.
Receptive Point on
the Module
Socket Key
2. Line up the bottom of the SO-DIMM memory module with the edge of the
horizontal socket.
3. Once they are lined up, push the memory module into the memory socket
until the module is securely seated in the socket.

DIMM Memory Removal

1. Use your thumbs to gently push the side clips on both ends of the socket
away from the SO-DIMM module to release it from the locked position.
Socket Side Clip
2. Once the memory module is loosened from the socket, pull it upwards and
outwards to remove it from the socket.
Status
Power On
AC On
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
SO-DIMM Memory
Module
Memory Module Socket
Socket Side Clip