Advertisement
Dimensions & Panel Cut-out
Character Display Unit
End Plate
Binary
Dec/Hex
Display Unit
Display Unit
6.5
20
20
20
20N + 13
6.5
Accessories (Optional)
Connector
Solder Terminal Connector
(DMC-1)
Applicable Wire: ø0.8mm maximum
AWG #22 maximum
11.3
6
IGHT
42
45.5
5
Dynamic Mother Board (not applicable to zero-suppress)
4-digit: DD9Z-MB1-4
2-digit: DD9Z-MB1-2
Connector for Data Input
Screw
Spacer
1.5
12-ø3.2 (for mounting mother board)
3-ø2.8 (for securing DD3S)
( 10 )
( 10 )
2
( 10 )
1
3
12
11
10
9
8
7
6
5
4
3
2
1
13
20
20
78 (Note)
Note: 38 mm for 2-digit mother board DD9Z-MB1-2
Panel Thickness 0.8 to 4
Spacer Unit
DD9Z-FY1-8
20
6.5
3.5
42
Display units can be combined
for up to 8 digits.
PC Board Terminal Connector
(DMC-2)
Applicable PC board thickness: 1.6
12-ø1 Holes
2
0.6
11.3
4
20
Substrate: Glass epoxy, 1.6-mm
thick
4.5
Nut
DD3S
Housing
( 10 )
0
For 4-digit
(Top View)
GND
<+> A
<1> C
Latch (10
)
0
Latch (10
)
2
7 * (10
)
0
7 * (10
10
6
)
2
6 *
20
14
DP (10
)
1
DP (10
)
3
Numbers marked with
DD3S
Panel Cut-out
For Connector Wiring
For Use of Dynamic Mother Board
20N + 10.5
IGHT
10
N = No. of digits (N ≤ 8)
∗ When using a static mother board
Retentive/One-way Insertion Connector
(DD9Z-CN1) (Note)
UP
13.1
Note: Use DD9Z-CN1 in combination with DD9Z-ST1 connector
stopper.
Note: The DD3S housing can be secured to the mother board using screws.
Recommended tightening torque is 3.5 N·m at the maximum. When
no spacer is used, the tightening torque must not exceed 2 N·m.
Connector
Spacer
DD3S Housing
Screws (M2.6 × 18), M2.6-3 nuts, and spacers are supplied with
the mother board.
Input Terminal Arrangement
For 2-digit
(Top View)
11 *
GND
1
2
B
<+> A
3
4
D <–>
<1> C
5
6
Latch (10
)
0
Latch (10
1
)
7
8
NC
Latch (10
3
)
9
10
7 * (10
7 * (10
)
0
1
)
11 12
7 * (10
NC
3
)
13 14
6 *
DP (10
0
)
15 16
DP (10
)
1
DP (10
2
)
17 18
NC
Vcc
19 20
*
are the DD3S terminal numbers.
Display Units
Series
All dimensions in mm.
3.5 min. (when mounting
+0.5
0
more than 8 units)
27.8
(min25)
5
1.7
6.8
1.5
PC Board
Screw M2.6 × 18
Nut
(M2.6)
Terminal Arrangement
by Models
2-
Standard
color
F3 ** F01 ** F3 **
11 *
GND
GND
1
2
B
NC
NC
3
4
D <–>
A
+
5
6
D
-
Latch (10
1
)
7
8
LAT
LAT
NC
9
10
7 * (10
BL
BL
1
)
11 12
R/G
LT
NC
13 14
C
1
DP (10
0
)
15 16
Vcc
Vcc
NC
17 18
B
NC
Vcc
19 20
DP
DP
NC
NC
13
1.6
6
No.
GND
12
NC
11
A
10
D
9
LAT
8
BL
7
LT
6
C
5
Vcc
4
B
3
DP
2
NC
1
11
Advertisement
