Related Manuals for IBM NuPRO-630
Summary of Contents for IBM NuPRO-630
- Page 1 NuPRO-630 ® Pentium -II Bus-100MHz VGA Full Size All-in-one PC/104 VGA CRT Interface Supports DMA33 WDT DOC USB IrDA PICMG Bus Industrial Single Board Computer...
- Page 2 Trademarks IBM PC is a registered trademark of International Business Machines Corporation. ALi is a registered trademark of ALi Corporation. AWARD is a registered trademark of AWARD International Inc.
-
Page 3: Table Of Contents
Contents CHAPTER1 GENERAL INFORMATION ...............1-1 1.1 M ....................1-2 AJOR EATURES 1.2 S ....................1-3 PECIFICATIONS 1.3 D ..................1-4 ELIVERY ACKAGE CHAPTER2 HARDWARE INSTALLATION............2-1 2.1 C ..............2-1 AUTION OF TATIC LECTRICITY 2.2 C ......2-2 AUTION ON NPACKING AND EFORE NSTALLATION 2.3 N... - Page 4 3.13 USB P ................3-10 ORTS ONNECTOR CHAPTER4 AWARD BIOS SETUP................4-1 4.1 M ......................4-2 4.2 S CMOS S ................. 4-3 TANDARD ETUP 4.3 BIOS F ..................4-4 EATURES ETUP 4.4 C ................4-5 HIPSET EATURES ETUP 4.5 I ................4-6 NTEGRATED ERIPHERALS 4.6 P...
-
Page 5: Chapter1 General Information
The NuPRO-630 also provides one set of PC/104 bus for 8/16-bit industrial application with based on PC/104 standard bus. With onboard DMA33 of mode 4 to IDE drive interface architecture, the NuPRO-630 supports with maximum 33.3 MB/sec in data transfer rating to 4 pieces IDE drive Design with ALi™... -
Page 6: Major Features
1.1 Major Features ü PICMG bus supported. ü PC/104 bus connector for 8/16-bit supported. ü One axial-horizontal type Slot-1 socket for Intel™ Pentium II 233∼450 MHz ® Processors. ü ALi™ M1621 BX -Level chipset. ü Three pieces DIMM sockets supports DRAM up to 1.5 GB. ü... -
Page 7: Specifications
1.2 Specifications ² CPU: One Intel Pentium II 233/266/300/333/400/450MHz. ® ² Bus interface: PICMG bus, PC/104 bus. ² Chipset: ALi™ M1621 BX -Level with bus-100MHz facility. ² Data bus: 64-bit ² Processing ability: 64-bit ² SVGA Controller: S3 86C375 chipset with 2MB memory supports CRT up to ®... -
Page 8: Delivery Package
² Operating temperature: 0-55°C (CPU need cooler) ² Board size: 13.26"(L) x 4.8" (W) (337mm x 122mm) The NuPRO-630 provides with VGA Interface, supports DMA33, WDT, DOC, USB and IrDA. The NuPRO-631 design is same as NuPRO-630 but without VGA interface. -
Page 9: Chapter2 Hardware Installation
Hardware Installation This ch apter provides the information on how to install the hardware of NuPRO-630. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, watchdog timer and the DiskOnChip™... -
Page 10: Caution On Unpacking And Before Installation
2.2 Caution on Unpacking and Before Installation First of all, please follow with all necessary steps of section 2.1 in protection the NuPRO-630 from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps: 1. -
Page 11: Nupro-630'S Layout
2.3 NuPRO-630’s Layout NuPRO-630’s Layout 2.4 Quick Listing of Jumpers — Bus-Clock Select JP1 ( 1-2 ON ) — Frequency Multiplier setting of System Bus to JP3 ( 3-4,7-8 ON ) Processor Core — RTC Clear Jumper JP4 ( 1-2 OFF ) —... -
Page 12: Quick Listing Of Connectors
2.5 Quick Listing of Connectors BZ1: ON-BOARD BUZZER CN1: INTERNAL 5-PIN KEYBOARD CONNECTOR CN2: RESET PIN CN3: SPEAKER CONNECTOR CN4: KEYLOCK CONNECTOR CN5: HDD LED CONNECTOR CN6: PS/2 POWER SWITCH CONNECTOR CN7: POWER 4-PIN CONNECTOR CN9: 1st IDE CONNECTOR CN10: 2nd IDE CONNECTOR CN13: PARALLEL PORT CONNECTOR CN16: FDD CONNECTOR CN17: INTERNAL VGA LCD CONNECTOR (HEADER 25x2) -
Page 13: Jumper Setting Description
2.6 Jumper Setting Description A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is OFF as a open circuit with a plastic cap inserted over one or no pin(s) between pins. The below figure 2.2 shows the examples of different jumper pin-set setting as ON or OFF in this manual. -
Page 14: Setting The Bus-Clock Frequency
2.7 Setting the Bus-Clock Frequency The NuPRO-630 provides all necessary by jumper setting in using Bus-Clock frequency as the system bus clocking with JP1 setting as following: Bus-Clock Frequency Setting of JP1: Bus-Clock Frequency * 100MHz 66MHz 2.8 Frequency Multiplier Setting... -
Page 15: Setting The Rtc Configuration
2.9 Setting the RTC Configuration The NuPRO-630 provides a setting for the selection of the RTC Clear Jumper by JP4 setting as following: CMOS Setting of JP4: CMOS Clear Jumper Normal * OFF Clear CMOS 2.10 System Memory DRAM The NuPRO-630 provides a wide range on-board DRAM memory by three pieces DIMM sockets (DIMM-1, DIMM-2, DIMM-3) request the access time should meet PC-100 standard.. -
Page 16: Watch-Dog Timer
2.12 Watch-Dog Timer There are three access cycles of Watch -Dog Timer as Enable, Refresh and Disable. The Enable cycle should proceed by READ PORT 443H. The Disable cycle should proceed by READ PORT 043H. A continue Enable cycle after a first Enable cycle means Refresh. -
Page 17: Pci Vga Controller (Nupro-630 Only)
; get back AX, DX 2.13 PCI VGA Controller (NuPRO-630 Only) The NuPRO-630 has built-in a S3 86C375 VGA Controller with on-board 2 MB memory, support resolutions up to 1280 x 1024 256 colors, reserved internal 10-pin VGA-CRT header connector. -
Page 18: Diskonchip™ Address Setting
2.14 DiskOnChip™ Address Setting The NuPRO-630 provides a U17 socket for install the DiskOnChip™ module. A JP7 may select the starting memory address of the DiskOnChip™ (D.O.C.) for avoid the mapping area with any other memory devices. If you have another extra memory devices in the system with the same memory, neither the NuPRO-630 nor the extra memory devices will function normally. -
Page 19: Chapter3 Connection
This chapter gives all necessary information of the peripheral's connections, switches and indicators. 3.1 Power and FAN Connectors The NuPRO-630 provides one 4-pin DC-Power connector as following CN7 pin information. And also provides one 3-pin fan out connector at solder side as following CN35 pin information. -
Page 20: Ide's Led, Key-Lock And Reset Button
3.2 IDE's LED, Key-Lock and Reset Button The NuPRO-630 h as one LED ( LD1 ) indicates out power-on status. And the following provides the pin information for IDE's LED indicator, Key-Lock and Reset Button connections from CN5, CN4 and CN2. -
Page 21: Pci E-Ide Drive Connector
3.4 PCI E-IDE Drive Connector Two standard 40-pin header daisy-chain driver connect ors provide as CN9 and CN10 with following pin assignment. Total four IDE (Integrated Device Electronics) drivers may connect. CN9 (IDE 1) : Primary IDE Connector CN9 : IDE Interface Connector PIN NO. -
Page 22: Ps/2 Power On/Off Control
INTERRUPT IOCS16#-DEFAULT HDC CS0 HDC CS1# HDD ACTIVE GROUND 3.5 PS/2 Power ON/OFF Control The NuPRO-630 reserved a CN6 for PS/2 Power ON/OFF Control. CN6 : PS/2 Power ON/OFF Control DESCRIPTION HIGH Switch Power OFF Switch Power ON 3-4 Connection... -
Page 23: Parallel Port Connector
3.6 Parallel Port Connector A standard 26-pin flat cable driver connector provides as CN13 with following pin assignment for connection to parallel printer. CN13 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5... -
Page 24: Serial Ports Connectors
DISK CHANGE# 3.8 Serial Ports Connectors The NuPRO-630 offers two high speeds NS16C550 compatible UARTs with Read/Receive 16 byte FIFO serial ports with one external DB-9 connector CN20 and one internal 10-pin header CN18. The NuPRO-630P which is with two external DB-9 RS-232 connectors CN20/26 and without VGA on-board. - Page 25 DATA CARRIER DETECT (DCD) RECEIVE DATA (RXD) TRANSMIT DATA (TXD) DATA TERMINAL READY (DTR) GROUND (GND) DATA SET READY (DSR) REQUEST TO SEND (RTS) CLEAR TO SEND (CTS) RING INDICATOR (RI) CN18 : Serial Port 10-pin Header (COM2) PIN NO. DESCRIPTION PIN NO.
-
Page 26: Keyboard Connectors
CN24 : 6-pin Mini-DIN Keyboard Connector PIN NO. DESCRIPTION KEYBOARD DATA GROUND KEYBOARD CLOCK 3.10 PS/2 Mouse 6-pin Mini-DIN Connector The NuPRO-630 provides an external PS/2 mouse connector at CN23 with following pin information. CN23 : PS/2 Mouse Connector PIN NO. DESCRIPTION DATA GROUND... -
Page 27: Vga-Crt Connector
3.11 VGA-CRT Connector The NuPRO-630 provides two possible connectives of VGA-CRT connections. One standard DB-15 external VGA connector as following CN22 pin information. Another internal 10-pin header f or VRA-CRT connection as following CN17 pin information. CN22 : 15-pin DB-15 Female VGA-CRT connector PIN NO. -
Page 28: Ir Connector
GROUND FIRRX IRTX IRRX CVROFF 3.13 USB Ports Connector The NuPRO-630 provides a internal 8-pin header for two USB ports connection. Please refer to the following detail pin information. JP19 : 8-pin Header USB Connector PIN NO. JP19 PIN NO. -
Page 29: Chapter4 Award Bios Setup
Chapter-4 AWARD BIOS Setup The NuPRO-630 uses the Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements. -
Page 30: Main Menu
4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>... -
Page 31: Standard Cmos Setup
4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode. -
Page 32: Bios Features Setup
4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot -up sequence, keyboard operation, shadowing and security. 4-4 AWARD BIOS Setup... -
Page 33: Chipset Features Setup
4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 34: Integrated Peripherals
4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. -
Page 35: Power Management Setup
4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. AWARD BIOS Setup 4-7...