Parts And Their Functions - Panasonic AW-HR140PJ Operating Instructions Manual

Parts and their functions

5
4
1
2
Rear panel
9
16
POWER/
10BASE-T/
STANDBY
RS-422 100BASE-TX
12V
ACT LINK
6 7 11
9
1.
Drop-prevention wire attachment hole
Use the screw provided to fix the drop-prevention wire.
2.
Hole for securing the camera pedestal
Four places in the camera pedestal.
3.
Camera head
This rotates in the up and down direction.
4.
Pan head
This rotates in the right and left direction.
5.
Wiper
Moves left and right to clear the lens.
3
2
9
8 10 12
SDI OUT
G/L IN 1/PM 2
MODE
IN
EXT
SIGNAL GND
AUDIO IN(1/2)
13 14 15
9
6. RS-422 connector <RS-422>
This RS-422 connector (RJ45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
LAN cable 1 (category 5 or above, straight cable), max. 1000 m
*
(3280 ft)
*
1
Use of an STP (shielded twisted pair) cable is recommended.
Pin
No.
1
2
3
4
<NOTE>
• Although the unit is not equipped with a tally lamp, "OSD Off With
Tally" function can be used when pin 1 (GND) and pin 2 (TALLY
signal) are shorted.
• Do not apply voltage to pin 2 (TALLY signal), as it is a contact input.
7. LAN connector for IP control <LINK/ACT>
This LAN connector (RJ45) is connected when exercising IP control
over the unit from an external device. Use a cable with the following
specifications for the connection to this connector.
When using a PoE++ Ethernet hub
LAN cable (category 5e or above, straight cable),
1
*
max. 100 m (328 ft)
When not using a PoE++ Ethernet hub
LAN cable (category 5 or above, straight cable),
* 1
max. 100 m (328 ft)
* 1
Use of an STP (shielded twisted pair) cable is recommended.
<NOTE>
• When connecting directly to a controller without an Ethernet hub,
use a cross cable.
8.
G/L IN connector <G/L IN>
This is the external sync signal input connector.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Format
1080/59.94p 480/59.94i
1080/29.97p 480/59.94i
1080/23.98p 480/59.94i
1080/59.94i 480/59.94i
1080/29.97PsF 480/59.94i
1080/23.98PsF ―
720/59.94p 480/59.94i
1080/50p 576/50i
1080/25p 576/50i
1080/50i 576/50i
1080/25PsF 576/50i
720/50p 576/50i
<NOTE>
• Locking to a subcarrier is not possible with BBS.
9.
Hole used to secure cable cover
Use screws to secure the cable cover.
10.
SDI OUT connector <SDI OUT 1/PM, SDI OUT 2>
This is the SDI video signal output connector.
• OSD output from the SDI OUT 1/PM connector is possible, so you
can display the camera menu and status on the monitor.
Operating Instructions
Pin
Signal Signal
No.
GND 5 TXD+
TALLY 6 RXD+
RXD– 7 —
TXD– 8 —
External sync signal input format
BBS Tri-level sync
1080/59.94i
—
1080/59.94i
1080/59.94i
1080/59.94i
1080/23.98PsF
720/59.94p
1080/50i
—
1080/50i
1080/50i
720/50p
35