Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Renesas H8SX/1648
Summary of Contents for Renesas H8SX/1648
- Page 1 REJ10J1869-0200 H8SX/1648 Group E6000H PLQP0144KA-A User System Interface Board HS1648ECH61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1648ECH61HE Rev.2.00 Revision Date: Apr. 18, 2008...
- Page 3 Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures.
-
Page 5: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface board. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 6: Limited Warranty
User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas’... - Page 7 This user's manual and user system interface board are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
- Page 8 • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol.
- Page 9 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 11 The HS1648ECH61H is a user system interface board that connects a user system for the H8SX/1648 PLQP0144KA-A (former package: FP-144L) package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1648 group is only possible when this user system interface board is connected to the HS1650EPH60H.
-
Page 12: Table Of Contents
Section 1 Configuration...1 Section 2 Connection Procedures ... 3 Connecting the User System Interface Board to the User System ... 3 2.1.1 Installing the IC Socket... 4 2.1.2 Soldering the IC Socket ... 5 2.1.3 Inserting the IC Socket Connector... 5 2.1.4 Fastening the IC Socket Connector... -
Page 13: Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for the PLQP0144KA-A package. Please make sure you have all of these components after you have unpacked the box. Screws (M2 × 6 mm) Socket cover Figure 1 User System Interface Board for the PLQP0144KA-A Package Section 1 Configuration... - Page 14 Use an NQPACK144SD-ND socket (manufactured by Tokyo Eletech Corporation) as the PLQP0144KA-A-packaged IC socket on the user system. Table 1 HS1648ECH61H Components No. Component User system interface board IC socket Socket cover Screws (M2 x 10 mm) Screws (M2 x 6 mm) Spacers (2.6MP x 25 mm) 2 Spacers (2.6MQ x 13 mm) 4 Screwdriver...
-
Page 15: Section 2 Connection Procedures
Section 2 Connection Procedures Connecting the User System Interface Board to the User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. -
Page 16: Installing The Ic Socket
To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. -
Page 17: Soldering The Ic Socket
2.1.2 Soldering the IC Socket After fastening, solder the IC socket for a PLQP0144KA-A package to the user system. Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector Check the location of pin 1 before inserting. -
Page 18: Fastening The Ic Socket Connector
2.1.4 Fastening the IC Socket Connector 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 19 User system Figure 3 Connecting the User System Interface Board to the User System Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation)
-
Page 20: Exchanging The Spacers Of The Evaluation-Chip Board
Exchanging the Spacers of the Evaluation-Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. -
Page 21: Connecting The User System Interface Board To The Evaluation-Chip Board
Connecting the User System Interface Board to the Evaluation-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. - Page 22 Figure 5 Connecting the User System Interface Board to the Evaluation-Chip Board Evaluation-chip board User system interface board Connector No. Evaluation-Chip Board Board Connector No. Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 23: Recommended Dimensions For The User System Mounting Pad (Footprint)
Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for a PLQP0144KA-A package (NQPACK144SD-ND: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU. -
Page 24: Dimensions Of The Evaluation-Chip Board And The User System Interface Board
Dimensions of the Evaluation-Chip Board and the User System Interface Board The dimensions of the evaluation-chip board and the user system interface board are shown in figure 7. Figure 7 Dimensions of the Evaluation-Chip Board and the User System Interface Board 140.0 Evaluation-chip board 118.5... -
Page 25: Dimensions After Connecting The User System Interface Board
Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system are shown in figure 8. Spacer (φ5.8) Figure 8 Dimensions of the Assembly after Connection of the User System Interface Board Evaluation-chip board IC socket (NQPACK144SD-ND... -
Page 26: Using The Emulator Without Connecting User System
Using the Emulator without Connecting User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. - Page 27 USER USER Figure 9 SW1 Jumper Socket Figure 10 Attaching Spacers Spacer (2.6MQ x 13 mm)
-
Page 28: Section 3 Installing The Mcu To The User System
Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. - Page 29 Screws (M2 x 6 mm) Pin 1 User system Figure 11 Installing MCU to User System Socket cover IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation)
-
Page 30: Section 4 User System Interface Circuits
Section 4 User System Interface Circuits The following user system interface circuits are required to use the emulator with the user system interface board. PD0-PD7 PE0-PE7 PJ2, PJ3 PK2-PK7 47 kΩ Sub-MCU TIOCA6 TIOCB6 TIOCA7 TIOCB7 TIOCA8 TIOCB8 TIOCA9 TIOCB9 PO16-PO23 PO24-PO31 Figure 12 User System Interface Circuit (1) - Page 31 Sub-MCU TIOCA0 TIOCB0 TIOCA1 TIOCB1 TIOCA2 TIOCB2 TIOCA3 TIOCB3 Figure 13 User System Interface Circuit (2) User system 47 kΩ...
- Page 32 Sub-MCU SCK5 RxD5 TxD5 Figure 14 User System Interface Circuit (3) SN74CB3Q3306A 47 kΩ SN74CB3Q3306A User system...
- Page 33 Sub-MCU SCK6 RxD6 TxD6 Figure 15 User System Interface Circuit (4) SN74CB3Q3306A SN74CB3Q3306A User system 47 kΩ...
- Page 34 User system 47 kΩ 47 kΩ EPM3256ATC Sub-MCU ADTRG0 Figure 16 User System Interface Circuit (5)
-
Page 35: Section 5 Verifying Operation
Supply the external clock from the user system to the emulator by inputting the signal to the EXTAL pin (pin 98) on the user system interface board or connecting a crystal oscillator to the XTAL (pin 97) and EXTAL pins. For details, refer to the H8SX/1648 Group Hardware Manual. - Page 36 ⎯ To use the crystal resonator mounted on the evaluation-chip board Install the crystal resonator into the crystal resonator terminals on the evaluation-chip board. Crystal resonator terminals Figure 18 Mounting the Crystal Resonator Enlarged view Crystal resonator Evaluation-chip board...
-
Page 37: Section 6 Points For Caution
Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. -
Page 38: Section 7 Restrictions
1. Deep-software standby mode This emulator does not support deep-software standby mode. Note that the emulator switches to the software standby mode even if the register setting to select the deep-software standby mode is made. 2. Sleep-instruction exception processing This emulator does not support the processing of sleep-instruction exceptions. Even if the SLPIE bit of the standby control register (SBYCR) is set to 1, the execution of a sleep instruction simply makes the emulator enter the low-power-consumption mode with no exception processing for the sleep instruction. - Page 39 8. A/D converter In the emulator, the evaluation chip and the slave chip are used to implement functions of Unit 0 and Units 1 and 2, respectively, of the A/D converter. For this reason, when the A/D control register (ADCR) has been set to start A/D conversion (with synchronization of units) by an external trigger from the ADTRG0 pin, the interrupt timing at the end of the A/D conversion will be different between Unit 0 and Unit 1.
- Page 41 HS1648ECH61H User's Manual Publication Date: Rev.2.00, April 18, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. ©2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
- Page 42 Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
- Page 44 H8SX/1648 Group E6000H PLQP0144KA-A User System Interface Board HS1648ECH61H User’s Manual...