Master / Slave Setup - Eagle AVI Installation & Owner's Manual

Master / Slave Setup

AVI
POWERED BY EAGLE
MASTER
Operator
IMPORTANT: The 120 VAC power for the master and slave operators MUST be on the SAME circuit breaker.
It is recommended that each gate operator's initial set-up is completed (Direction of gate travel, limit nuts,
ERD reverse sensor and feature selector switches #1 - #4) before connecting the operators together.
After each operator functions individually, proceed to Master/Slave connection and operation.
#8 #9
SLAVE MASTER
+ – + –
Master
Operator
COMM PORT COMM PORT
Master Operator
SELECT
SLAVE MASTER
OPEN LEFT OPEN RIGHT
BRAKE OFF BRAKE ON
CLOSE TIMER OFF CLOSE TIMER ON
OFF—ON
FEATURE SELECTOR
Switch #1 MUST be ON. Refer to
page 11 for more information
about each of the features.
SELECT
OPEN OPENING CLOSING CLOSED
CLOSE TIMER OFF LIMIT LIMIT
CLOSING
OFF—ON
FEATURE SELECTOR GATE STATUS
0 1
M/S PHASE
ERD OVERLOAD
Master Board
GND
RCVR
GND
#2
POWER
Close Timer
(Master Operator)
Use the Close Timer (Feature
Selector #4 ON) on the master
board ONLY to set the gates
closing time 1 - 60 seconds.
Clockwise increases close time.
TIMER
AVI Slide Rev - C
Opens to the Left
Connect Master and Slave Operators Together
Choose your board type (Master or Slave) and use 20
GA stranded wire. Correct polarity is VERY important.
DO NOT cross polarity. Operators will NOT function
properly if not wired correctly. Make sure to use color
coated wire.
Negative to Negative 20 AWG Wire
Positive to Positive 20 AWG Wire
NOTE: #1 & #2 switch settings are
based on the illustration above.
ACCESSORIES NOTE: Connect accessories to
the master or slave boards).
See page 16 for accessory wiring connections.
0
M/S PHASE
Opens to the Right
Jumper
1
SELECT SELECT
SLAVE SLAVE MASTER MASTER
OPEN LEFT OPEN LEFT OPEN RIGHT OPEN RIGHT
OPEN OPENING CLOSING CLOSED
BRAKE OFF BRAKE OFF BRAKE ON BRAKE ON
CLOSE TIMER OFF CLOSE TIMER OFF CLOSE TIMER ON CLOSE TIMER ON OPENING CLOSING LIMIT LIMIT
OFF—ON OFF—ON
FEATURE SELECTOR EATURE SELECTO TIMER ERD CONTROL GATE STATUS
M/S PHASE NOTE: If the Master and Slave
S1 S2 FCN
0 1
ON ON STOP N/C
ON OFF CLOSE
RESET
M/S PHASE OFF ON PHANTOM
OFF OFF EDGE SENSOR
MULTI FUNCTION
ERD OVERLOAD
operators are NOT communicating properly,
verify that they are on the same phase by
switching the M/S Phase jumper on either
GND #1
RCVR
24VAC
the master or the slave unit. Make sure to
GND
reset both boards.
#2 #3 #4 #5 #6 #7 #8 #9
SLAVE MASTER
+ – + –
INPUT/OUTPUT COMM PORT COMM PORT POWER
AVI
POWERED BY EAGLE
SLAVE
Operator
#8 #9
SLAVE MASTER
+ – + –
Slave
Operator
COMM PORT COMM PORT
Slave Operator
SELECT
SLAVE MASTER
OPEN LEFT OPEN RIGHT
BRAKE OFF BRAKE ON
CLOSE TIMER OFF CLOSE TIMER ON
OFF—ON
FEATURE SELECTOR
Switch #1 MUST be OFF.
Switch #4 MUST be OFF. Refer to
page 11 for more information
about each of the features.
SELECT
SLAVE MASTER R
OPEN LEFT OP OPEN RIGHT GHT
BRAKE OFF R BRAKE ON N OPEN OPENING CLOSING CLOSED
CLOSE TIMER OFF CLOSE TIMER ON OPENING CLOSING LIMIT LIMIT
OFF—ON
FEATURE SELECTOR TIMER ERD CONTROL GATE STATUS
S1 S2 FCN
0 1 ON ON STOP N/C
ON OFF CLOSE
M/S PHASE RESET OFF ON PHANTOM
OFF OFF EDGE SENSOR
MULTI FUNCTION
ERD OVERLOAD
Slave Board
GND
#1
RCVR
24VAC
GND
#2 #3 #4 #5 #6 #7 #8 #9
SLAVE MASTER
+ – + –
INPUT/OUTPUT COMM PORT COMM PORT POWER
17