Related Manuals for AURES ODP 333
Summary of Contents for AURES ODP 333
- Page 1 ODP 333 ::: Receipt Printer User’s Manual ::: All specifications are subject to change without notice...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. Parts Identifications 2. Setting up the printer 2.1 Unpacking 2.2 Connecting the cables 2.3 Loading the roll paper 3. Control panel and other functions 3.1 Control panel 3.2 Error Indicating 4. Self Test 5. Hexadecimal Dump 6. -
Page 5: Parts Identifications
1. Parts Identifications PRINTER COVER FEED BUTTON POWER SWITCH POWER CONNECTOR INTERFACE CONNECTOR(SERIAL) INTERFACE CONNECTOR(USB) INTERFACE CONNECTOR(ETHERNET) PERIPHERAL DRIVE CONNECTOR... -
Page 6: Setting Up The Printer
2. Setting Up the Printer 2-1. Unpacking Your printer box should include following items. If any of the following items are damaged or missing, please contact your dealer for assistance. Printer Paper (Drivers and Documentation) Adaptor (Option) Interface Cable (Option) -
Page 7: Connecting The Cables
2-2. Connecting the Cables In order to use the printer, you are required to connect cables to the printer. All cables connect to the connector panel on the rear side of the printer, which is shown below: POWER CONNECTOR For connection of the INTERFACE CONNECTOR(SERIAL) AC adapter. -
Page 8: Interface Connector
2-2-1. Interface Connector <USB “B” Type> <9 Pin Serial> <Ethernet> - USB interface SIGNAL DESCRIPTION DATA- Printer transmit data line DATA+ Printer transmit data line System Ground - 9Pin Serial Interface SIGNAL DESCRIPTION Printer receive data line RS-232C level Input Printer transmit data line RS-232C level Output Printer handshake to host line RS-232C level... -
Page 9: Cash Drawer Connector
2-2-2. Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 1.0A for 510ms or less when the printer is not printing. SIGNAL DESCRIPTION Signal GND Drawer kick-out drive signal 1... -
Page 10: Loading The Roll Paper
2-3. Loading the Roll Paper Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. (Turn off power switch) ☞... - Page 11 5. Note the correct direction of how paper comes off the roll. 6. Pull out a small portion of paper, as shown. Then, close the cover. 7. Tear off the paper as shown.
- Page 12 ☞ CAUTION: When the paper is jammed from cutter, the top cover might be stuck as well. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming. 1.
-
Page 13: Control Panel And Other Functions
3. Control panel and other functions. 3-1. Control panel You can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you to monitor the printer’ s status. PAPER ERROR FEED BUTTON POWER BUTTON Button... -
Page 14: Self Test
4. Self Test The self-test result indicated whether the printer is operating properly. Also with this, user can check following options or status of the printer. Control circuit Printer mechanism Printing quality ROM version Interface setting This test is independent of any other equipment or software. -
Page 15: Hexadecimal Dump
6. Select Baudrate Mode After entering the BAUDRATE MODE, the list which can select the BPS will be printed. Similar like Self Test, you can press the FEED button to select a BAUDRATE. Once the input performs properly, the printer shows a result and store. The printer is ready to receive data as soon as it completes the SELECT BAUDRATEMODE. -
Page 16: Printer Cleaning
8. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. ♣Note : 1. Make sure to turn the printer power off prior to cleaning 2. -
Page 17: Specifications
9. Specifications 9-1. General Specifications (1) Printing Method Direct line thermal printing. (2) Print speed 160 mm/sec. (Approx 35.4LPS) (3) Dot density 180 DPI (Hor / Ver) 180 / 180 (0.141mm / 0.141mm dot) (4) Printing Width 180 DPI Max 72mm (512 dots) (5) Number of print columns. - Page 18 (8) Overall dimension...
-
Page 19: Auto Cutter Specifications
9-2. Auto Cutter Specifications (1) Cutting Frequency Max. 30 cuts per minute (2) Thickness of paper 0.06 ~ 0.09mm (3) Cutter Life 1.5 million cuttings (if the paper thickness is between 65 and100µm) 9-3. Interface RS232C Serial Interface, USB Interface, Ethernet Interface(100Mbps) 9-4. -
Page 20: Environmental Requirements
♣Important! When using a printer power supply other than optional AC adaptor, be sure to follow below instructions. Use a power supply (Limited Power Supply) of DC 24V±10% and more than 1.75A. Be careful when installing the printer in an area where there is noise. Take the appropriate measure to protect against electrostatic AC line noise, etc. -
Page 21: Command List
10. Command List Command Function REMARKS Horizontal tab Print and line feed Print and carriage return Print and return to standard mode(in page mode) Cancel print data in page mode DLE EOT Real-time status transmission DLE ENQ Real-time request to printer DLE DC4 Generate pulse at real-time ESC FF... - Page 22 Command Function REMARKS GS * Define downloaded bit image GS / Print downloaded bit image GS B Turn white/black reverse printing mode on/off GS H Select printing position of HRI characters GS I Transmit printer ID GS L Set left margin GS P Set horizontal and vertical motion units GS V...
- Page 23 :: MEMO ::...