Related Manuals for AURES ODP-200H-III
Summary of Contents for AURES ODP-200H-III
- Page 1 3” Thermal Printer ODP-200H-III All specifications are subject to change without notice...
- Page 2 A software tool is available to configure the printer settings on AURES technical website: www.aures-support.fr...
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1. Parts Identifications 2. Setting up the printer 2.1 Unpacking 2.2 Connecting the cables 2.3 Loading the paper 3. Control panel and other functions 3.1 Control panel 3.2 Error Indicator 4. Self Test 5. Hexadecimal Dump 6. Specifications 6.1. -
Page 5: Parts Identifications
1. Parts Identifications... -
Page 6: Setting Up The Printer
2. Setting Up the Printer 2-1. Unpacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. The Printer User's Manual Roll Paper Adaptor(Option) Interface Cable(optional) -
Page 7: Connecting The Cables
2-2. Connecting the Cables You can connect up the cables required for printing to the printer. They all connect to the connector panel on the back of the printer, which is shown below : POWER CONNECTOR INTERFACE CONNECTOR For connection of the AC INTERFACE CONNECTOR(USB) For connection to a adapter. - Page 8 2-2-1. Interface Connector <D-SUB 25 Female Serial> <Centronics Parallel> <USB “B” Type> <Ethernet> Serial Interface PIN SIGNAL DESCRIPTION Output Printer transmit data line RS-232C level Input Printer receive data line RS-232C level 4, 20 Output Printer handshake to host line RS-232C level Input Data Send Ready 1, 7...
- Page 9 Centronics Parallel Interface SIGNAL DESCRIPTION STROBE- Input Synchronize signal Data received DATA0~7 Input/Output Data bit Transmitted 0~7 ACK- Output Data receiving completed. BUSY Output Impossible to print of data receiving. Output Paper empty SELECT Output Printer status for ON/OFF line AUTO FEED- Input Paper auto feed signal...
- Page 10 2-2-2. Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 0.1A for 510ms or less when not printing. SIGNAL DESCRIPTION Signal GND Drawer kick-out drive signal 1 Output Drawer open/close signal...
-
Page 11: Loading The Roll Paper
2-3. Loading the Roll Paper Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. (Turn off power switch) 1. - Page 12 4. Insert new paper roll as shown. 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper, as shown. Then, close the cover. 7. Tear off the paper as shown.
- Page 13 ♣CAUTION: When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming. 1.
-
Page 14: Control Panel And Other Functions
3. Control panel and other functions. 3-1. Control panel You can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you to monitor the printer’s status. Control Panel POWER ERROR PAPER Button... -
Page 15: Self Test
4. Self Test The self-test lets you know if your printer is operating properly. It checks the control circuits, printer mechanisms, print quality, ROM version and DIP switch settings. This test is independent of any other equipment or software. Running the self test 1. -
Page 16: Hexadecimal Dump
5. Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hex dump function, the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands. -
Page 17: Specifications
6. Specifications Appendix A : Specifications 6-1. General Specifications (1) Printing Method Direct line thermal printing. (2) Print speed 200mm/sec. (3) Dot density 180 DPI (Hor / Ver) 180 / 180 (0.142mm / 0.142mm dot) (4) Printing Width 180 DPI Max 72mm (512 dots) (5) Number of print columns. - Page 18 (8) Overall dimension...
-
Page 19: Auto Cutter Specifications
6-2. Auto Cutter Specifications (1) Cutting Frequency Max. 30 cuts per minute (2) Thickness of paper 0.06 5~ 0.09 mm (3) Cutter Life 1.5 million cuttings (if the paper thickness is between 65 and100µm) 6-3. Interface RS232C Serial Interface, Centronics Parallel Interface(IEEE1284), USB Interface Ethernet Interface(10Mbps) 6-4. -
Page 20: Environmental Requirements
♣Important! When connecting or disconnecting the power supply from the printer, be sure that the following cautions are observed. (1) Use a power supply (Limited Power Supply) of DC 24V±10% and more than 1.75A. (2) Be careful about installing the printer in an area where there is noise. (3) Take the appropriate measure to protect against electrostatic AC line noise, etc. -
Page 21: Command List
7. Command List Command Function REMARKS Horizontal tab Print and line feed Print and carriage return Print and return to standard mode(in page mode) Cancel print data in page mode DLE EOT Real-time status transmission DLE ENQ Real-time request to printer DLE DC4 Generate pulse at real-time ESC FF... - Page 22 35 ESC c 3 Select paper sensor(s) to output paper-end signals 36 ESC c 4 Select paper sensor(s) to stop printing 37 ESC c 5 Enable/disable panel buttons 38 ESC d Print and feed paper n lines 39 ESC p General pulse 40 ESC t Select character code table...
- Page 23 FS C Select Kanji character code system FS S 1 2 Set Kanji character spacing 10 FS W Turn quadruple-size mode on/off for Kanji character...
- Page 24 Rev. 1.0...