Related Manuals for AURES SMP 58
Summary of Contents for AURES SMP 58
- Page 1 MOBILE PRINTER MODEL : SMP 58 Wi-Fi & Bluetooth SMP 58 Rev. A 08/18 All specifications are subject to change without notice...
- Page 2 Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Aures USA Jeff Burroughs 15042 Parkway Loop, Building D, Tustin, CA 92780 | USA +714.669.3111...
-
Page 3: Table Of Contents
Table of Contents 6. Roll Media Specification 1. Safety Precautions 7. Black Mark 2. Unpacking 8. Cleaning the Printer 3. Product Overview 4. Usage and Installation 9. Printer Specification 4-1. Control Panel Usage 4-2. Battery Installation 4-3. Battery Removal 4-4. Battery Charging 4-4-1. -
Page 4: Safety Precautions
1. Safety Precautions For better safety and reliability, adhere to the following precautionary measures. WARNING Read and follow the instructions carefully before operation of the product. Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage. Indication Prohibition Must follow... -
Page 5: Unpacking
2. Unpacking 3. Product Overview Standard Front Control Panel Power Button Printer Battery Belt Strap+Bracket Quick Manual Open Button Paper feed Button Charger CD (Manual) Roll paper DC Power USB Cable Rear Set Cradle Adaptor AC Cord (Charging Cradle) Battery Belt clip hole... -
Page 6: Usage And Installation
4. Usage and Installation 4-1 Control Panel Usage 4-2 Battery Installation Hook Button Name function This button is used to turn the printer on and off. Power When the printer is off, press this button for approximately 3 seconds Button and the printer will power on. -
Page 7: Battery Removal
4-4 Battery Charging 4-3 Battery Removal 4-4-1 Charging Usage OPEN Lamp 1. Make sure the printer is turned off. Remove the battery as shown 2. After opening the DC JACK cover, connect the DC JACK to the printer. 3. Plug the power cord into the electrical outlet. The charging status LED Status charging... -
Page 8: Charging Cradle
4-4-2 Charging Cradle 4-5 Set Cradle Usage Press the PUSH button to pop out the cradle connector. 1. Place the printer into the charging cradle as shown above. 2. Connect the DC JACK to the charging cradle. NOTE 3. Plug the power cord into an electrical outlet. 4. -
Page 9: Belt Strap+Bracket Usage
4-6 Belt Strap+Bracket Usage After connecting the strap and bracket, insert the screws Prepare the belt strap, Put the strap into the hole on the into the bracket hole. bracket, and 2 screws. top of the belt bracket. Use a screw driver to tighten the bracket. -
Page 10: Paper Installation
4-7 Paper Installation 4-8 Self Test Turn off the power by pressing While you are holding the FEED the power button for approximately Press the PUSH button to open Insert the paper in the correct button, press the power button. 3 seconds. -
Page 11: Peripheral Connection
5. Peripheral Connection This product can communicate with other devices via Bluetooth, Wi-Fi, or a communication cable. Self-Test Printout Sample Upon initial installation or for troubleshooting, you can run the diagnostic test to get information about: Firmware version, emulation, codepage, sensor settings, interface settings, etc. -
Page 12: Nfc Connection Optional
Optional 5-1-1. NFC Connection 5-2. Wi-Fi Connection Optional This product can communicate with other devices via NFC. 1. The Printer can be connected to devices equipped with Wi-Fi communication capabilities (PDAs, PCs, etc.). 2. Use the Wi-Fi connection function supported by the device to connect to the printer. 1. -
Page 13: Interface Cable Connection
6. Roll Media Specification 5-3. Interface Cable Connection Core Diameter(A) 12.5mm +/-0.5mm Roll Max.diameter(B) 40mm 1. Connect USB cable to the connector on the printer. Max.Media Width (C) 58 ± 0.5mm NOTE Min.media Thickness 0.06mm Use the cable offered by the manufacturer (USB) 2. -
Page 14: Black Mark
7. Black Mark 8. Cleaning the Printer If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning. 2. -
Page 15: Printer Specification
9. Printer Specification Printing Method Direct Thermal Interface Standard Printing Speed Max. 100mm/s Option Bluetooth Smart Ready Ver 4.2 or Wi-Fi(802.11a/b/g/n) Resolution 203 DPI Reliability 50km Character ESC/POS FontA(12x24), FontB(9x17), Asian Font(KOR, JPN,CHN_GB2312,CHN_BIG5) Battery Charger Input AC100~240V, 50/60Hz CPCL Font0/1/2/4/5/6/7, 24x24 Asian Font(KOR, Output 8.4V , 800~1400mA JPN,CHN_GB2312,CHN_BIG5), Resident TTF,...