Inventory - Grizzly G0621X Owner's Manual

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Main Components: (Figure 2)
A. Bandsaw Unit ............................................. 1
B. 6" Handwheel ............................................. 1
C. Handwheel Handle ..................................... 1
D. Miter Gauge ................................................ 1
E. Table .......................................................... 1
F.
Scale .......................................................... 1
G. Table Insert ................................................ 1
H. Stand Door Knob ⁄
5
I.
Dust Port 2 ⁄ " ............................................. 1
1
2
J. Table Trunnion Knobs
K. Rear Rail .................................................... 1
L.
Front Rail .................................................... 1
M. Front Rail L-Brackets ................................. 2
N. L-Bracket Knobs
⁄
5
16
O. Fence Assembly ......................................... 1
P. Stand Assembly ......................................... 1
Fasteners and Tools: (not shown)
• Rubber Feet (Stand) .................................. 4
• Hex Bolts ⁄ "-18 x 1" (Feet) ...................... 4
5
16
• Flat Washers ⁄ " (Feet) ............................. 4
5
16
• Hex Nuts ⁄ "-18 (Feet) .............................. 4
5
16
• Hex Bolts ⁄ "-18 x 3" (Stand/Bandsaw) .... 4
5
16
• Flat Washers ⁄ " (Stand/Bandsaw) ........... 8
5
16
• Hex Nuts ⁄ "-18 (Stand/Bandsaw) ............ 4
5
16
• Hex Bolt ⁄ "-16 x 3
3
8
• Hex Nut ⁄ "-16 (Positive Stop) ................... 1
3
8
• Cap Screws ⁄ "-20 x
1
4
• Front Rail T-Slot Nuts (Front Rail) ............. 2
• Cap Screws ⁄ "-20 x
1
4
• Guide Blocks (Blade Guides) ..................... 4
• Thumbscrews ⁄ "-20 x
1
4
• Phlp Hd Screws 10-24 x
• Hex Wrenches 3, 5, 8mm ................. 1 each
• Flat Wrench 12/14mm ................................ 1
• Lock Nut ⁄ "-18 (Stand Guard) ................. 1
5
16
-12-
Qty
"-18 x 1" ..................... 1
16
⁄ "-16 ..................... 2
3
8
"-18 x ⁄ " ..................... 2
5
8
Qty
⁄ " (Positive Stop) ........ 1
1
2
⁄ " (Front Rail) .......... 2
5
8
⁄ " (Rear Rail) ........... 2
5
8
⁄ " (Blade Guides) . 4
1
2
⁄ " (Dust Port) ..... 4
1
4
A
B
D
C
I
G
K
J
H
M
N
P
Figure 2. Main components inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Model G0621X (Mfd. Since 07/17)
E
F
L
O