Roland CAMM JET CJ-70 User Manual page 44

Top menu Submenus
INK CONTROL
INK EMPTY
FILL INK
PUMP-UP
CHANGE INK
COLOR CHART —
PEN SETUP
ALL
PEN NO.0,—,15
SYSTEM INFO —
FEED MARGIN —
PREFEED
DISABLE
ENABLE
CALIBRATION
X AXIS
Y AXIS
SLEEP —
HEAD CLEANING
TEST PRINT
NORMAL [KC]
NORMAL [MY]
POWERFUL
POWERFUL
42
When replacement of the ink cartridge becomes necessary while printing is
in progress, this setting determines whether printing continues or pauses.
This setting is used when the ink cartridge cannot be changed immediately
during printing, such as during unattended operation at night.
"LATER" causes printing to continue without pause even if ink refilling be-
comes necessary. Printing continues with the small amount of ink remaining,
so the printed image may become faint as the ink runs out. In general, it
should possible to perform about 1 m
appears, although the actual varies widely according to the amount of ink
needed for the particular image. Printing is continued only for the data
currently being printed. Operation stops after one image is output.
"PROMPT" causes operation to pause immediately when the ink cartridge
needs to be changed. Printing is resumed by replacing the cartridge and
pressing the PAUSE key. Please note, however, that the colors of an image
in progress may no longer be perfectly matched if the unit is allowed to
remain paused for two or three hours before resuming printing.
Refills the printing heads with ink. Normally there is no need to do this,
because refilling is automatic.
Drains ink from the printing heads. Be sure to do this when moving the unit.
Performs the "PUMP-UP" and "FILL INK" operations.
This outputs a color chart, allowing confirmation of how colors appear.
This makes the settings for the pen when printing RD-GL III (vector)
commands.
WIDTH sets the pen width.
COLOR INDEX sets the color numbers output with COLOR CHART.
Settings are made for all pens.
The setting is made for the corresponding pen from 0 to 15.
This prints the current status of settings and other system information.
This sets the distance (margin) for the interval after printing or cutting ends
until the next printing or cutting operation begins.
When using roll material, this automatically feeds out a specified length and
checks to make sure the material is gripped correctly.
The prefeed check function is disabled.
The prefeed check function is enabled.
The length that is fed after loading the material is also set.
This compares the distance set using the application software with the actual
output distance, and performs necessary calibration (for cutting only).
Calibration is performed for the X axis.
Calibration is performed for the Y axis.
This sets the time that elapses before the unit enters the SLEEP mode.
This cleans the printing heads. This causes a certain amount of head wear
and also consumes a certain amount of ink, so use should be kept to a
minimum.
POWERFUL results in faster head wear and also uses up much ink.
Test printing is performed in a range of approx. 130 mm x 15 mm (5-1/8" x
9/16"). If a problem in printing occurs, follow this by performing cleaning
for the heads.
This performs cleaning for only two heads ("BLACK" and "CYAN").
This performs cleaning for only two heads ("MAGENTA" and "YELLOW").
[KC] This performs cleaning for only two heads ("BLACK" and "CYAN").
If the printing problem is not corrected after performing cleaning with
"NORMAL" several times, select "POWERFUL."
[MY] This performs cleaning for only two heads ("MAGENTA" and "YELLOW").
If the printing problem is not corrected after performing cleaning with
"NORMAL" several times, select "POWERFUL."
Function
2 2
(10 ft ) of printing once this message
Setting range Default value
LATER, PROMPT LATER
— —
WIDTH = 0.13, 0.18, WIDTH
0.25, 0.35, 0.50, 0.65, = 0.35 mm
PEN
0.70, 0.80, 0.90, 1.00,
No.
1.40, 2.00, 3.00, 5.00,
0—8
8.00, 12.0 (mm)
9
10
COLOR INDEX=0—255
11
(color ID.) 12
13
14
15
— —
0 mm to 100 mm 20 mm
(in increments of 5 mm)
ENABLE
0.5 m (19-5/8") to
25.0 m (984-1/7")
(in increments of
0.5 m (19-5/8"))
-0.19% to +0.19%
(in increments of 0.01%)
0.00%
0.00%
NONE, 15 min to 120 min 15 min
(in increments of 15 min)
— —
COLOR
INDEX
0—8
12
19
27
35
68
100
110