Roland CAMM JET CJ-70 User Manual page 43

Top menu Submenus
PRINT QUALITY
NORMAL
DRAFT
SUPER
BISUPER
FINE
BIFINE
OVER PRINT —
DRYING —
MIRROR
DISABLE
ENABLE
MEDIA TYPE
OPAQUE
CLEAR
UP SPEED —
CROP MARK
DISABLE
ALIGN
PRINT
DITHER
SCATTER
CLUSTER
VECTOR MODE
COMMAND
CUT
PRINT
INSTRUCTION —
TIME OUT —
AUTO ROTATE
DISABLE
ENABLE
FACTORY —
DEFAULT
SERIAL PORT *1
BAUDRATE
PARITY
HANDSHAKE
HEAD ADJUST
TEST PRINT
HORIZ. MAGENTA
HORIZ. CYAN
HORIZ. YELLOW
VERT. MAGENTA
VERT. CYAN
VERT. YELLOW
BIDIRECTION
PRINT-CUT ADJ
Function
This selects the quality level for printing.
The settings for print quality are, in order of increasing quality, DRAFT,
NORMAL, BIFINE, FINE, BISUPER, and SUPER. Please note that
printing times also grow longer as the quality level is increased.
Printing is performed in one direction. Normally this setting is selected.
High-speed, bidirectional printing is performed.
Printing is performed in four passes per stroke. Printing is in one direction.
Printing is performed in four passes per stroke. Printing is bidirectional.
Printing is performed in two passes per stroke. Printing is in one direction.
Printing is performed in two passes per stroke. Printing is bidirectional.
This sets the number of passes for overprinting. This setting is used when
working with highly absorbent media with little shrinkage or expansion, such
as fabrics, for which colors may not come out well with only a single
printing. Depending on the medium used, overprinting may result in ink
running or stretching of the material.
This sets the drying time for the ink. A long time should be set for
low-absorbency, hard-to-dry materials. When printing is followed by
cutting, the unit waits for the time set here until cutting begins.
This causes the image to be reversed from left to right.
The image is not reversed from left to right.
The output image is reversed from left to right.
This setting is used when creating an image on the back of a piece of material.
This is used to select either transparent or opaque material.
Select "OPAQUE" when the material loaded on the unit is not transparent.
Select "CLEAR" when the material loaded on the unit is transparent.
Only the horizontal width of the material is detected. (This is equivalent to
selecting "ROLL" when set to "OPAQUE").
Sets the tool-up speed of movement during cutting.
Crop marks are not output.
Crop marks are output. When printing is followed by cutting, distance
adjustment and angle adjustment are performed for the material.
Only crop marks are output (no adjustment is performed).
This selects the dither pattern. The appropriate pattern may vary according
to the image.
This is a nonuniform pattern.
This is a uniform pattern.
This sets the processing method used for RD-GL III (vector) commands.
Varies according to the commands received.
Cutting is performed.
Printing is performed.
Selects the RD-GL II or RD-GL III instruction set.
When a certain amount of time passes with no data sent from the computer,
the current output is considered to be finished.
"TIME OUT" sets the time used for this determination.
This rotates the output image to match the direction of the material. The
lengthwise direction of the material is automatically taken to be the X axis.
Auto-rotate is not performed.
Auto-rotate is performed.
This returns all menu settings to their original values when shipped from the
factory.
This sets the communication parameters for a serial connection.
Sets the transmission speed.
Makes the setting for parity checking.
Makes the setting for handshaking.
This adjusts the position of the heads, in 1-dot steps. The unit is set with a
unique value at the factory, and the setting returns to this value when
"FACTORY DEFAULT" is selected.
This prints a test pattern for adjustment of the head positions.
Adjusts the horizontal position of the magenta head.
Adjusts the horizontal position of the cyan head.
Adjusts the horizontal position of the yellow head.
Adjusts the vertical position of the magenta head.
Adjusts the vertical position of the cyan head.
Adjusts the vertical position of the yellow head.
Adjusts the position when bidirectional printing is performed in 0.5-dot steps.
Adjusts the position when both printing and cutting are performed.
*1: The settings for data length (8 bits) and the stop bit (1 bit) cannot be changed.
Setting range Default value
— NORMAL
NONE, 2—9TIMES NONE
NONE, 10 to 990 sec. NONE
(in increments of 10 sec.)
— DISABLE
— OPAQUE
10, 20 to 80, 85 cm/s 85 cm/s
— DISABLE
— CLUSTER
— COMMAND
RD-GL3, RD-GL2 RD-GL3
NONE, 10 to 990 sec. NONE
(in increments of 10 sec.)
— DISABLE
— —
19200, 9600, 4800 9600
NONE, EVEN, ODD NONE
NONE, XON/OFF, H-WIRE
H-WIRE, BOTH
— —
41