Mounting The Chassis Onto The Case; Assembly Information - Kenwood NX-5400 Service Manual

3.3.3 Mounting the chassis onto the case

(1) Place the key top on the chassis. Then, fit the chassis tight-
ly into the groove of the key top. <1>
Note:
Confirm that the entire groove of the key top fits to the
chassis tightly.
(2) Mount the chassis onto the case. <2>
Note:
• After mounting the chassis onto the case, if the 18-key
part on the key top or the Auxiliary (Orange) key part
of the VOL/SEL packing gets stuck inside the case as
shown in the figure, return it to the normal position us-
ing a soft tipped item (e.g., finger) . <3>
• Prying it with a pointed metal tool such as forceps, may
damage the key top or packing.
3.3.4 Assembly Information (Sheet/Cushion)
When "Main Parts" is changed (ordered), "Assembled Sheet / Cushion" should also be changed (ordered) together.
The Sticker and Sheet etc are non-reusable parts. It requires the new one to get the radio's performance after repairs.
For example, when "Plastic Cabinet (A0C-0001-00 (F3,K3)/ A0C-0002-00 (F2,K2))" is changed, "Badge (B4D-0002-00)", "Fibrous
Sheet (G1A-0001-00)", "Sheet (G1B-0074-00)", "Spacer (J3K-0003-00)" and "Knob (K2K-0013-00)" should be ordered and changed
together because Badge (B4D-0002-00), Fibrous Sheet (G1A-0001-00), Sheet (G1B-0074-00), Spacer (J3K-0003-00) and Knob
(K2K-0013-00) are non-reusable.
Main Parts
Part Name
Plastic Cabinet (F3,K3)
Plastic Cabinet (F2,K2)
Rear Panel
Terminal (ANT)
Terminal Block
Cover (OP board)
Shielding Cover (MPU)
Shielding Cover (LCD)
Holder (F3,K3)
FPC (UNIV)
FPC (PTT)
FPC (VOL, SEL, ECM)
Speaker
1-28 (No.RA016<Rev.001>)
Part Number Part Name
A0C-0001-00 Badge
A0C-0002-00
Fibrous Sheet (SP)
Sheet (LCD)
Spacer (2CH)
Knob (2CH)
A8A-0005-00 Sheet (Air)
E2D-0003-00 Cushion (ANT)
E7C-0001-00 Terminal Sticker
F0G-0005-00 Cushion (Cover)
F1B-0005-00 Sheet (Insulating)
F1B-0006-00 Cushion (LCD/Front)
J1K-0004-00 Cushion (20-pin Connector) G1D-0021-00
J87-0056-05 R.Receptacle
J87-0057-05 Sheet (PTT)
J87-0058-05 Sheet (Conducting)
Cushion
T0H-0002-00 Rubber Cushion (SP)
<2>
<1>
Assembled Sheet/ Cushion
Part Number
B4D-0002-00 "KENWOOD" is printed.
G1A-0001-00
G1B-0074-00
J3K-0003-00
K2K-0013-00
G11-4440-04
G1D-0041-00
B4C-0105-00
G1D-0062-00
G1B-0031-00
G1D-0009-00
E58-0532-05
G1B-0016-00
G11-4459-04
G1D-0025-00
G1B-0045-10
18-key part
Auxiliary
(Orange) key
<3>
Remark