Enter To The Front Panel Programming Mode; Data Writing; Key Operation - Kenwood NX-5400 Service Manual

The following setup items can be changed or added by us-
ing the Front panel programming mode.
• RX/TX Frequency
• Channel Type
• Channel Spacing
• Decode QT/DQT/RAN/NAC, Encode QT/DQT/RAN/NAC
• Talkgroup ID List No.
• Transmit Power
• Channel Name
Key guide on the Clone/ Front Panel Programming Pass-
word input screen.
• Confirm ([ ] key): The password confirmation
• Delete ([ ] key): Delete the latest digit from the current
password number (Press and hold to delete all password
numbers)
• Select ([ ] key): Determine the latest digit of the password
number.
2.2.8.1

Enter to the Front panel programming mode.

Enter to the Menu Mode by pressing [Front Panel Mode] PF key
or [Menu] key. When the Front Panel Mode is selected, it can en-
ter to the Front panel programming mode.
If the Clone/Front panel programming Password is not set to the
transceiver, "Panel Program" is displayed on the LCD.
If the Clone/Front panel programming Password is set to the
transceiver, "Panel Program" is displayed on the LCD when you
enter the correct password while "Input Password" is displayed.
2.2.8.2

Data Writing

Before moving to next Zone/Channel, "Keep This Change?" ap-
pears on the LCD, if you select "OK", the new data is written to
memory. If you select "Cancel", the new data not be written; the
new data will be erased.

• Key operation

Key\Item Zone Select Channel
[ ] Decision Decision
[ ] Unused Back to the
previous
item
[ ] Unused Unused
[ ] Exit panel pro- Exit panel
gram mode program
mode
[ ] Zone change Channel
change
[ ] Zone change Channel
change
[ ] Unused Unused
[ ] Unused Unused
Keypad Zone number Channel
[0] ~ [9] select number
*3 select
Keypad Decision Decision
[*] *3
RX Frequency TX Frequency
Select
Decision Decision
Back to the pre- Back
vious item previous item
Unused TX Frequency
OFF
Exit panel pro- Exit panel pro-
gram mode gram mode
Fresuency up Fresuency up
Frequency Frequency
down down
Frequency step Frequency
change step change
Frequency step Frequency
change step change
Go to the direct enter mode
Decision Decision
• The setup items for Front panel programming mode are as
follows.
No. Setup item
1 RX Frequency RX Frequency Receive Frequency
2 TX Frequency TX Frequency
3 Channel Type Channel Type
4 Channel Channel Space Analog:12.5kHz/20kHz/
Spacing
5 RX Signaling RX QT/DQT
6 TX Signaling TX QT/DQT
7 RX RAN RX RAN
8 TX RAN TX RAN
9 RX NAC RX NAC
10 TX NAC TX NAC
11 Talkgroup ID Talkgroup
List Number
12 Transmit Power Transmit Power Low/Medium/High
13 Channel Name Channel Name
Channel Channel
Type Spacing
Decision Decision
to the Back to the Back to the
previous item previous item
Unused Unused
Exit panel Exit panel
program program
mode mode
Channel type Channel
change Spacing
Change
Channel type Channel
change Spacing
Change
Unused Unused
Unused Unused
Channel Channel
number spacing
select (1 or 2) select (1 or 2)
Decision Decision
Display Remarks
Transmit Frequency
Analog/P25
25kHz
P25: 12.5kHz
Receive QT/DQT
Transmit QT/DQT
None, 1~63
None, 1~63
000~FFF
(Hexadecimal)
Note: "F7F" cannot set.
000~FFF
(Hexadecimal)
Note: "F7F" cannot set.
None, 1~1500
RX Signaling TX Signaling
Decision Decision
Back to the Back to the
previous item previous item
Unused Unused
Exit panel Exit panel
program program
mode mode
Signaling Signaling
number number
change change
Signaling Signaling
number number
change change
Signaling type Signaling
change type change
Signaling type Signaling
change type change
Go to the direct enter mode
Decision Decision
(No.RA016<Rev.001>)1-7