Accessories; Installation; Precautions; Power Supply - Kenwood TM-3530A Instruction Manual

2-2. ACCESSORIES
Unpack your TM-8530A/2570A/2550A/2550E/2530A carefully and confirm that it
is supplied with the following accessories.
@ Dynamic microphone
Dynamic microphone (England only}.
@ Hook
@ Tapping screw .
(T91-0357-05) ..
(T91-0335-05) ..
ws (J19-1346-04) ..
.. {N87-4008-41) ..
1 pe.
1 pc.
a T po.
«2 pes.
@® Mobile mounting kit
a. Bracket (A13-0668-04) .. we T pe.
b. Bracket assy (Right) . (A13-0666-02) .. . Tpe.
c. Bracket assy (Left) (A13-0667-02) .. .1 pe.
d. Cushion we {G13-0823-04) . . 4 pes.
e. Allen bolt (Black) ... . (N99-0304-04) . . 4 pes.
f. Hex socket screw . . (NO9-0008-04) . . 4 pes.
g. Flange nut wo. (N14-05 10-04). . 4 pes.
h. Flat washer (Black) . (N15-1040-45) .
i, Flat washer .... . (N15-1060-46) .
j. Spring washer . (N16-0060-46) .
k. Tapping screw .. . {NO9-0632-05) ....
1. Hex wrench .......
@® DC power cable for TM-2570A
DC power cable for TM-3530A/2550A/
ZBBOE/2530A wise cecccscssstssseceseseneeneeessteneesnennens {E30-2022-15) ......ce 1 pe.
@® Spare fuse for TM-2570A (20A) .. (FO5-2034-05) .. 1 pe.
Spare fuse for TM-2550A/2550E (10A) .. (FO5-1031-05) 1 pe.
Spare fuse for TM-3530A/2530A (8A) (FO5-802 1-05) . 1 pe.
OO FOOt caine ew waandiakieed: (JO2-0439-05) .. 4 pes.
instruction manual (Excluded in England)... {B50-8039-20} 1 copy
Instruction manual (England only} (B50-8040-00) 1 copy
Warranty card (U.S.A. only) .. (B46-0410-00) ... . 1 copy
(W01-0401-05) ....
. (E30-2044-05) ....
Shipping container:
Save the boxes and packing in the event your unit needs to be transported for remote
operation, maintenance, or service.
3-1-1. Precautions
1. Avoid direct sunlight, and select a dry, well ventilated
location.
2. Since the heat sink is on the rear panel, avoid placing
the equipment with the bottom and rear sides close to
a wall or desk.
3. When installing the equipment in an automobile, en-
sure adequate ventilation. Install the equipment in a
location where the rear does not make direct contact
with the seat, and is not directly exposed to vibration.
4, Avoid installing the equipment in front of the car
heater air outlet.
3-1-2. Power supply
The standard operating voltage of transceiver is 13.8 V.
Do not use a power supply (both fixed and mobile} that
provides over 16 V with the power switch of transceiver
turned off.
Operation under such a condition will void the warranty.
Also, do not use a power supply that does not supply at
least 12V in transmit or receive. Use of such a supply
"may cause the performance of the equipment to suffer.
3-1-3. Mounting bracket
Using the supplied mounting bracket, install the trans-
ceiver in any convenient location. (Fig. 3-1)
Caution:
Do not install the speaker directly on the transceiver, it
may cause howling. The heat sink provided at the rear of
the transceiver will get hot during long transmission. Do | Underside of
not install the radio in a position where the heat sink may dashboard
come in direct contact with the dashboard. Installation
near heater air outlets should also be avoided.
If your car is equipped with an electronic fuel injection
system, the transceiver should be mounted as far from
the control equipment as possible.
Side of console:
Install the bracket as shown in Fig. 3-2 and Fig. 3-3.
Note:
Do not install backwards.
Ae Body
Body
nf
lat
rae washer Fiat washer from your knees.
Mounting Spring
bracket Bolt washer
Tapping screw
The transceiver should be located
Underside of
dashboard
Drill holes in the bottorn of
dashboard. Secure the mounting
bracket with nuts and bolts.
Fig. 3-1
Mounting
bracket
Fig. 3-2