Kenwood NX-5400 Service Manual page 62

Item Condition
Panel tuning mode
4. 1) Adj item:
Low [An LRSSI]
RSSI Adjust:[***]
2) Adj item:
[Frequency:
700MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
-118dBm(0.28µV)
(MOD:1kHz/
±1.5kHz)
5. 1) Adj item:
High [An HRSSI]
RSSI Adjust:[***]
2) Adj item:
[Frequency:
700MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
-80dBm(22.4µV)
(MOD:1kHz/
±1.5kHz)
6. 1) Adj item:
Tight [Aw SQLT]
Squelch Adjust:[***]
2) Adj item:
[Analog [Frequency:
Wide 700MHz Band]
5k] [RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
12dB SINAD level
at Analog Narrow
+6dB(MOD:1kHz/
±3kHz)
1-62 (No.RA016<Rev.001>)
Measurement
PC test mode Test-
equip-
ment
1) Adj item: SSG
[Low RSSI (Analog
Narrow]
2) Adj item:
[Frequency:
700MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
-118dBm(0.28µV)
(MOD:1kHz/
±1.5kHz)
1) Adj item: SSG
[High RSSI (Analog
Narrow]
2) Adj item:
[Frequency:
700MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
-80dBm(22.4µV)
(MOD:1kHz/
±1.5kHz)
1) Adj item: SSG
[Tight Squelch (Ana- Distor-
log Wide 5k)] tion
2) Adj item: meter
[Frequency: Oscillo-
700MHz Band] scope
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
[Frequency:
800MHz Band]
[RX/TA Low]→
[RX/TA Center]→
[RX/TA High]
SSG output:
12dB SINAD level
at Analog Narrow
+6dB(MOD:1kHz/
±3kHz)
Unit Ter- Unit Parts
minal
Panel ANT Panel
Uni-
versal
con-
nector
Panel ANT Panel
Uni-
versal
con-
nector
Panel ANT Panel
Uni-
versal
con-
nector
Adjustment
Method
[Panel tuning mode]
After input signal from
SSG, press [ ] key to
store the adjustment val-
ue.
[PC test mode]
After input signal from
SSG, press [Apply] button
to store the adjustment
value.
[Panel tuning mode]
After input signal from
SSG, press [ ] key to
store the adjustment val-
ue.
[PC test mode]
After input signal from
SSG, press [Apply] button
to store the adjustment
value.
[Panel tuning mode]
After input signal from
SSG, press [ ] key to
store the adjustment val-
ue.
[PC test mode]
After input signal from
SSG, press [Apply] button
to store the adjustment
value.
Specifi-
cations
/Remarks