Kenwood NX-5800 Service Manual page 50

Item Condition
Panel tuning
mode
13. 1) Adj item: [ADEV]
Maxi- Adjust:[****]
mum Deviation meter
Devia- LPF: 15kHz
tion HPF: OFF
*2 2) Adj item:
[Low1]→
[Analog [Low3]→
Wide] [Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
[Analog 1) Adj item:
Narrow] [An ADEV]
Adjust:[****]
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
*2 : Refer to the "4.9.1 Necessary Deviation adjustment item for each signaling and mode" table.
Regarding Maximum Deviation (Analog), it is common with the adjustment of all analog signalings.
1-50 (No.RA017<Rev.002>)
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Devia-
[Maxmum Devia- tion
tion (Analog Wide)] meter
Deviation meter Oscil-
LPF: 15kHz lo-
HPF: OFF scope
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Devia-
[Maxmum Devia- tion
tion (Analog Nar- meter
row)] Oscil-
2) Adj item: lo-
[Low1]→ scope
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[ ],
[ ]
[PC
test
mode]
[←],
[→]
Adjustment
Method
Write fixed value for 4150~4250Hz
each adjustment point.
(The value is written be- [PC test
low.) Transmit at each mode]
adjustment point and Press [Apply
check that the deviation All] button to
is between 4150Hz and store the
4250Hz. adjustment
Deviation meter value after all
LPF: 15kHz adjustment
HPF: OFF points have
been adjusted.
505 (F,K)
503 (F2,K2)
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
Write fixed value for 2050~2150Hz
each adjustment point.
(The value is written be- [PC test
low.) Transmit at each mode]
adjustment point and Press [Apply
check that the deviation All] button to
is between 2050Hz and store the
2150Hz. adjustment
Deviation meter value after all
LPF: 15kHz adjustment
HPF: OFF points have
been adjusted.
505 (F,K)
499 (F2,K2)
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
Specifica-
tions
/Remarks