Kenwood NX-5800 Service Manual page 34

No. RX
13 Single Tone Decode
(979.9Hz)
14 None
15 None
16 MSK Decode
P25 Phase1 signaling
No. RX
1 NAC 293
2 NAC 023
3 NAC 5EA
4 None
5 NAC 293
6 NAC 293
7 NAC 293
8 NAC 293
9 None
10 None
11 Tone Pattern
12 Silence Pattern
13 Audio Test Pattern
14 Vocoder Loop
P25 Phase2 signaling
No. RX
1 STTP-OB-1031-0
2 None
3 STTP-OB-1031-1
4 STTP-OB-1031-1
5 STTP-OB-1031-1
6 STTP-OB-1031-1
7 STTP-OB-1031
8 Tone Pattern (Half rate) STTP-IB1031-1
9 Silence Pattern
(Half Rate)
10 Audio Test Pattern
(Half Rate)
11 Codec Loop
12 Vocoder Loop
(Half Rate)
1-34 (No.RA017<Rev.002>)
TX
Single Tone Encode
(979.9Hz)
Single Tone Encode
(1000Hz)
MSK PN9
MSK Encode
TX
NAC 293
NAC 023
NAC 5EA
PN9
Symbol Rate Pattern
1/3 Deviation Pattern
0 Continuous Pattern
Fidelity Pattern
FSW+PN9
1011Hz Tone Test Pattern
1011Hz Tone Test Pattern
Silence Pattern
NAC293 + Audio Test Pat-
tern
None
TX
STTP-IB1031-1+Audio
PN9 Phase2
Symbol Rate Pattern
Phase2
1/3 Deviation Pattern
Phase2
0 Continuous Pattern
0 Burst Pattern
Symmetrical
STTP-IB1031-1
STP-IB-1 +
Silence Pattern (Half Rate)
STTP-IB1031-1 + Audio
Test Pattern (Half Rate)
STTP-IB1031-1 + Codec
Loop
STTP-IB1031-1 +
Vocoder Loop (Half Rate)
NXDN Mode signaling
No. RX
1 RAN1
2 None
3 RAN1
7 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
RAN: Radio Access Number
PN9: Pseudo-Random Pattern
No.7, 9 Item: PC test mode only
4.3 Panel Tuning Mode
4.3.1 Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [
is in test mode. Use the [ ] key to write tuning data through tun-
ing modes, and the [ ]/[
(1 to 4096 appears on the LCD).
Use the [ ] key to select the adjustment item through tuning
modes. Use the [ ] key to adjust 4, 6 or 8 reference level ad-
justments, and use the [
Wide4k/Narrow.
• LCD display in panel tuning mode
CV voltage, AD value, etc
Sub LCD 2.6 Low1
display
An RAST
Main LCD
display
Proper value guide
(When the frequency
An: Analog narrow mode
adjustment is necessary,
As: Analog wide 4k mode *1
Aw: Analog wide mode
P1n: P25 Phase1 mode Adjustment item
P2n: P25 Phase2 mode
Nn: NXDN narrow mode
Nv: NXDN very narrow mode
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims
at production for factory, or a operation verification of the transceiver. It is
not necessary in operation of the transceiver to adjust.
TX
RAN1
PN9
Maximum Deviation
Pattern
FSW + PN9
] key while the transceiver
] key to adjust tuning requirements
] key to switch between Wide5k/
256
Adjustment value
Adjustment point
(1~4096)
Low1 Center4
Low2 Center5
Low3 High1
Low4 High2
or is displayed.)
Low5 High3
Low6 High4
Center1 High5
Center2 High6
Center3